Video Channel Setting; Automatic Channel Setup; Manual Channel Preset; Follow Tv (Automatic Tv Channels Sorting) - Philips DVP620VR/05 User Manual

Setting Up your DVD/VCR

Video Channel Setting

Video channel setting will be necessary, if your DVD/VCR is
connected to the TV via the coaxial cable.
1 Insert a pre-recorded tape into the DVD/VCR.The DVD/VCR
will turn on and start playback automatically.
If playback does not start, press PLAY B .
2 Select and adjust your TV to channel 35.
• If the playback picture appears on the TV screen, continue
with step 8.
• If channel 35 is employed for broadcasting, or interference
lines appear on the picture, the RF converter must be set to
a different channel between CH22 and CH69. Continue with
step 3.
3 Press DISC/VCR MENU.
4 Press K/L to select "INITIAL SET
UP".Then, press B.
5 Press K/L to select "RF OUT".
Then, press B twice.
6 Press K/L to select a channel
which is not used for broadcasted
between channel 22 and channel 69
in your area, then press B.
• You can also see the selecting RF channel in the display
7 Press STATUS/EXIT to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the DVD/VCR. A picture from the VCR will appear
on the TV screen. If a picture does not appear, repeat steps 3 to
7 using a different channel which is not used for broadcasted.
8 Press STOP C to stop the tape.
Note:
– You may also access the RF OUT CH menu by pressing
and holding DISC/VCR MENU for 3 seconds during
power off until the RF OUT CH menu appears.

Automatic Channel Setup

You can programme the tuner to scan only the channels that
you can receive in your area.
1 Turn on the TV and select the video out channel on your TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select "TUNER SET UP", then press B.
4 Press K/L to select "AUTO TUN-
ING", then press B.
• The tuner scans and memorizes
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorized
channel.
5 Press P +/– or numerical key pads
to scan through channels you have received.
Sorting of TV channels from P01 to P06 will be
performed automatically as follows.
P01: BBC1
P03: ITV
P05: CH5
8
SELECT K L CHOOSE B
RF OUT CH 35
SET=0-9
END=EXIT
PLEASE WAIT
START FINISH
P02: BBC2
P04: CH4
P06: SKY NEWS

Manual Channel Preset

1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "TUNER SET UP", then press B.
3 Press K/L to select "MANUAL
TUNING", then press B.
4 Press K/L to select "PROG"., then
press B.
5 Press K/L or numerical key pads
to select your desired programme
number, then press B.
• You can select programme num-
ber 01-99.
6 Press K/L to select "CHANNEL", then press B.
7 Press K/L.The DVD/ VCR tuner will begin to search up or
down automatically.When a channel is found, the DVD/ VCR
will stop searching and the picture will appear on the TV
Screen.
• You can select desired channel number by using numerical
key pads. Press three digits to select the channel number. (To
select channel 24, first press "0" button then press "2" and "4").
• If this is the channel you want, press B.
• If you want to remove scrambled signals, press K/L to select
"DECODER".Then, press B to select "[ON]".
8 Press STATUS/EXIT to exit.
Notes:
– To confirm that a channel has been added, press the P
+/– buttons.
– You should select the satellite channels to be received by
the satellite receiver directly on the receiver itself.

Follow TV (Automatic TV channels sorting)

When the automatic channel search function is activated, the
TV channels are saved in a specific order.This may vary from
the order of TV channels on the TV.
This function changes the order of TV channels saved in the
DVD/ VCR to match that of the TV.
Make sure that the DVD/ VCR and the TV are connected by a scart cable.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select "TUNER SET
UP", then press B.
3 Press K/L to select "FOLLOW
TV" , then press B.
4 "P:01" will appear in the DVD/
VCR display.
I cannot switch my TV to programme number "1"
If you have connected additional devices to socket
AV2(DECODER), please disconnect these devices. Because of
other connected devices, the TV could switch to the programme
number of the scart socket.
"NO TV SIGNALS" appears in the TV screen.
The DVD/ VCR is not receiving a video signal from the TV.
Check the plug on the scart cable.
Check your TV's operating instructions to see which scart socket
is used for video signals.
If this does not help, it's not possible to use this function. Please
read the section 'Sorting TV channels manually'.
5 Select programme number "1" on the TV.
6 Confirm with B on the DVD/ VCR remote control.The DVD/
VCR compares the TV channels on the TV and the DVD/ VCR.
If the DVD/ VCR finds the same TV channel as on the TV, then
it stores it at "P01".
7 Wait until the next number, e.g. "P:02" appears in the display.
8 Select the next programme number on the TV, e.g. "2".
9 Confirm with B.
10 Repeat steps 7 to 9 until you have assigned a programme num-
ber to all TV channels.
11 To end, press STATUS/EXIT.
MANUAL TUNING
PROG. P55
CHANNEL 055
DECODER [OFF]
SKIP [OFF]
SET=K L OR 0 – 9
END=EXIT
SELECT K L CHOOSE B
AUTO TUNING
MANUAL TUNING
FOLLOW TV
MOVE
END=EXIT