Setting Up Your Dvd/Vcr; Important For The United Kingdom; Basic Connections; Connecting To A Tv - Philips DVP620VR/05 User Manual

Setting Up your DVD/VCR

Important for the United Kingdom

This apparatus is fitted with an approved moulded 13 Amp
plug.To change a fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 3A,ASTA or BSI
approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 3A.
If a plug without a fuse is used, the fuse at the distribution
board should not be greater than 3A.
The severed plug must be destroyed to avoid a possible
shock hazard should it be inserted into a 13A socket
elsewhere.
How to connect a plug:
The wires in the mains lead are coloured in accordance with
the following code:
BLUE- 'NEUTRAL' ('N')
BROWN- 'LIVE' ('L')
4 The BLUE wire must be connected to the terminal which is
marked with the letter 'N' or coloured BLACK.
5 The BROWN wire must be connected to the terminal which is
marked with the letter 'L' or coloured RED.
6 Do not connect either wires to the earth terminal in the plug
which is marked with the letter 'E' or by the safety earth
symbol or coloured green or green-and-yellow.
Before replacing the plug cover, make certain that the cord grip
is clamped over the sheath of the lead-not imply over the two
wires.

Basic Connections

• Please refer to the instruction books of your TV,VCR, Stereo
System or other devices as necessary to make the best con-
nections.
• Make one of the following connections, depending on the
capabilities of your existing equipment.
The following guidelines are options for the best picture and
sound quality available on your DVD/ VCR.
Picture
1 Use SCART RGB Output (DVD/ VCR(AV1 TV)) for best pic-
ture quality (for DVD and VCR features).
2 Use S-VIDEO Output for the better picture quality (for DVD
features only).
3 Use SCART Composite Output for good picture quality (for
DVD and VCR features).
4 If your TV only has a RF-style (Antenna IN or 75 ohm) input,
use the RF OUT for connection and set your TV to channel 22
~ 69 with the same channel for DVD/ VCR is set (for DVD and
VCR features).
Sound
1 Digital audio connections provide the clearest sound. Connect
the DVD/ VCR DIGITAL AUDIO OUT (either COAXIAL or
OPTICAL) to your amplifier or receiver (for DVD features only).
2 Use SCART Output (DVD/ VCR(AV1 TV)) for better sound
quality (for DVD and VCR features).
If digital connections are not possible, connect the DVD/ VCR
ANALOG AUDIO OUT(Left and Right) to your amplifier,
receiver, stereo or TV (for DVD features only).
Warning!
– Never make or change connections with the power
switched on.
– Connect the DVD/ VCR directly to your TV, instead of eg.
a VCR, to avoid distortion because DVD video discs are
copy protected.
– Do not connect the ANALOG AUDIO OUT of DVD/ VCR
to PHONO IN of your amplifier or receiver.
– If you use the Euro audio/video cable, it is not necessary
to connect the analog audio cable.
6

Connecting to a TV

1 Connect the antenna or cable to the AERIAL of your DVD/
VCR.
2 Connect the DVD/ VCR (AV1 TV) on the DVD/ VCR to the
corresponding connector on the TV.
Note:
– Ensure that the "TV" indication on SCART cable is con-
nected to the TV set and "DVD" indication on SCART
cable is connected to the DVD/ VCR.
If your TV is not equipped with a SCART input, you can select
the following connection:
If your TV has a S-Video input connector,
1 Connect the antenna or cable to the AERIAL of your DVD/ VCR.
2 Connect the S-Video out on the DVD/ VCR to the S-Video in
on the TV.
3 Connect the ANALOG AUDIO OUT on the DVD/ VCR to the
Left and Right audio in on the TV.
OR
DVD
DIGITAL ANALOG S-VIDEO
AUDIO OUT AUDIOOUT OUT
VCR
L
DVD/VCR
OPTICAL COAXIAL
R
Note:
– You will still need the SCART cable or RF coaxial cable
for VCR features.
Simplest connection using only supplied
black RF coaxial cable
1 Disconnect the antenna or cable from your TV.
2 Connect the antenna or cable to the AERIAL of your DVD/ VCR.
3 Connect black RF coaxial cable to the RF OUT on the rear
panel of the DVD/ VCR and to the ANTENNA IN on the TV.
4 Plug in the power cords of the TV and DVD/ VCR.
Antenna
Indoor/Outdoor
(300 ohm)
OR
Cable
(75 ohm)
Connecting to an Audio System
(for DVD features)
1 You can also listen to the sound of audio CDs and DVD video
discs by connecting to an optional stereo system.
2 Connect DVD/ VCR ANALOG AUDIO OUT (Left and Right)
to the audio in on the stereo system.
STEREO
AUDIO (LEFT) IN
AUDIO (RIGHT) IN
DVD
DIGITAL ANALOG S-VIDEO
AUDIO OUT AUDIOOUT OUT
VCR
L
DVD/VCR
OPTICAL COAXIAL
R
TV
AERIAL
AV2(DECODER)
AV1(TV) RF OUT
Back of DVD/VCR
(on back of TV)
example only
DVD
DIGITAL ANALOG S-VIDEO AERIAL
AUDIO OUT AUDIOOUT OUT
VCR AV2(DECODER)
L
OPTICAL COAXIAL DVD/VCR AV1(TV) RF OUT
R
AERIAL
RF OUT
75
ANT
CABLE
Black RF
coaxial cable
(Supplied)
AV2(DECODER)
AV1(TV)
Antenna In
1
L/MONO
AUDIO
R
VIDEO
in
AERIAL
RF OUT