Table of Contents
Advertisement
H9924RD_EN_0316 3/17/05 10:11 AM Page 7
External Input Mode (for VCR features)
To receive the signal from an external input (decoder, satellite
receiver, video camera, another VCR etc.), connect to the AV2
(DECODER) socket, and enter '0.0.2.' with numerical key pads
to appear "AV2" on the TV screen.
If you use the AV1 (TV) socket, enter '0.0.1.' with numerical key
pads to appear "AV1" on the TV screen.
If you use the front AUDIO/VIDEO IN jacks, enter '0.0.3.' with
numerical key pads to appear "AV3" on the TV screen.
Inserting batteries into the Remote Control
1 Open the battery cover.
2 Insert batteries (AA size) with the
correct polarity as indicated by the
+ and – symbols inside the battery
compartment.
3 Close the cover.
CAUTION!
– Remove batteries if they are exhausted or not to be used
for a long time.
– Do not use old and new or different types of batteries in
combination.
– Batteries contain chemical substances, so they should be
disposed off properly and kept away from children.
Using the Remote Control
• Direct the remote control at the remote sensor of the DVD/
VCR.
• Do not drop the remote control.
• Do not leave the remote control near extremely hot or
humid place.
• Do not spill water or put anything wet on the remote control.
Playable Video Tapes
Philips Consumer Electronics recommends that only video
tapes that have the VHS mark and High Quality (HQ) system is
compatible with this unit.This unit has an Automatic Head
Cleaner.
Recording Prevention
Video tapes have record tabs to ensure
recordings are not erased accidentally.
1 To prevent recording, break off the tab with a
screw-driver.
2 To allow recording, cover the hole with
cellophane tape.
Notes:
– Use only video tapes with VHS mark.
– Remove any adhesive stick-on notes from the video tape
before inserting into the DVD/VCR.
– Periodic maintenance is required to maintain your DVD/
VCR performance.
– Video heads will require replacement after a period of
time. Only an authorised service center should perform
this service.
Turning on your DVD/ VCR
The following steps only be performed when you insert the AC
PLUG at the first time.
1 Turn on the TV and select the
video channel on the TV.
2 Plug in the DVD/VCR.
3 Press K/L repeatedly to select
your desired language.
4 Press DISC/VCR MENU.
5 Confirm with P+.
The Auto Tuning starts.
6 "TIME" and "DATE" will appear on
the TV screen.
7 Check "TIME". If required, please
change the time with numerical key
pads.
8 Check if the displayed settings for
"DAY", "MONTH" and "YEAR" are
correct.
9 When all information is correct,
save by pressing STATUS/EXIT.The
preparation for use is now
complete.
Note:
– When Auto Tuning has been completed, the initial set-
tings menu will not appear even if the AC plug has been
unplugged or after a power failure.To recall this initial
settings menu, press SOURCE and VCR PLAY B on the
system's front panel at the same time for more than 2
seconds when the power is off.
Video Channel Setting
Video channel setting will be necessary, if your DVD/VCR is
connected to the TV via the RF Coaxial cable.
1 Insert a pre-recorded video tape into the DVD/VCR.The
DVD/VCR will turn on and start playback automatically.
If playback does not start, press PLAY B .
1
2 Select and adjust your TV to channel 36.
• If the playback picture appears on the TV screen, continue
with step 8.
• If channel 36 is employed for broadcasting, or interference
lines appear on the picture, the RF converter must be set to
2
a different channel between CH22 and CH69. Continue with
step 3.
3 Press DISC/VCR MENU.
4 Press K/L to select "INITIAL SET
UP".Then, press B.
5 Press K/L to select "RF OUT".
Then, press B twice.
6 Press K/L to select a channel
which is not used for broadcasted
between channel 22 and channel 69
in your area, then press B.
• You can also see the selecting RF channel in the display.
7 Press K/L to select "TV SYSTEM".Then, press B.
8 Choose "K" or "G".Then, press B.
9 Press STATUS/EXIT to exit.
Set the TV channel to the RF OUT CHANNEL which was
selected on the DVD/VCR. A picture from the VCR will appear
on the TV screen. If a picture does not appear, repeat steps 3
to 7 using a different channel which is not used for
broadcasted.
10 Press STOP C to stop the video tape.
Note:
– You may also access the RF OUT CH menu by pressing
and holding DISC/VCR MENU for 3 seconds during
power off until the RF OUT CH menu appears.
Setting Up your DVD/ VCR
SELECT K L
ENGLISH
FRANÇAIS
ESPAÑOL
DEUTSCH
ITALIANO
SVENSKA
NEDERLANDS
PUSH MENU TO CONTINUE
START
TIME 10:00
DATE 25/ 12/ 05
SMART CLOCK [ON]
END=EXIT
SELECT K L CHOOSE B
RF OUT CH 36
TV SYSTEM K
SET=0-9
END=EXIT
PLEASE WAIT
FINISH
7
Advertisement
Table of Contents
