Page 3
Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.
T T T T T ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS ABLE OF CONTENTS Preface Chapter 1 Introducing the Motherboard Introduction....................1 Feature......................2 Motherboard Components................4 7 7 7 7 7 Chapter 2 Installing the Motherboard Safety Precautions..................7 Choosing a Computer Case...............7 Installing the Motherboard in a Case............7...
Page 6
Integrated Peripherals..............40 Power Management Setup............43 PNP/PCI Configurations.............46 PC Health Status................47 Frequency/Voltage Control............48 Load Fail-Safe Settings..............49 Load Optimized Defaults.............49 Set Supervisor/User Password............49 Save & Exit Setup.................50 Exit Without Saving..............50 Chapter 4 51 51 51 51 51 Using the Motherboard Software About the Software CD-ROM..............51 Auto-installing under Windows 2000/XP..........51 Running Setup................52 Manual Installation..................54...
SATA v1.0 compliant, supporting four SATA ports with maximum transfer rate up to 1.5 Gb/s each. The RS482M-M motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and keyboard connectors, COM1, LPT, VGA, four USB ports, one optional LAN port, and audio jacks for microphone, line-in and line-out.
Feature Processor The RS482M-M uses an AM2 socket that carries the following features: • Accommodates AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/Athlon 64/ Sempron processors • Supports up to 2000MT/s HyperTransport (HT) interface speeds HyperTransport Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.
Page 9
Audio • Compliant with AC’97 V2.3 specification • Supports 6-channel audio CODEC designed for PC multimedia systems • Provides three analog line-level stereo input with 5-bit volume control: line-in, CD, AUX • Meets Microsoft WHQL/WLP 2.0 audio requirements Expansion Options The motherboard comes with the following expansion options: •...
Chapter 2 Installing the Motherboard Safety Precautions • Follow these safety precautions when installing the motherboard • Wear a grounding strap attached to a grounded device to avoid damage from static electricity • Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard •...
Do not over-tighten the screws as this can stress the motherboard. Checking Jumper Settings This section explains how to set jumpers for correct configuration of the motherboard. Setting Jumpers Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered.
Checking Jumper Settings The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. Jumper Settings Type Jumper Description Setting (default) 1-2: NORMAL 2-3: CLEAR CLR_CMOS CLR_CMOS 3-pin CLEAR CMOS Before clearing the CMOS, make sure to turn off the system.
Connecting Case Components After you have installed the motherboard into a case, you can begin con- necting the motherboard components. Refer to the following: Connect the CPU cooling fan cable to CPU_FAN. Connect the system cooling fan connector to SYS_FAN. Connect the case switches and indicator LEDs to the PANEL1.
Page 17
CPU_FAN/SYS_FAN: FAN Power Connectors Signal Name Function System Ground Power +12V +12V FAN1,2 Sense Fan control PWM signal ATX12V: ATX 12V Power Connector Signal Name Ground Ground +12V +12V ATX_POWER: ATX 24-pin Power Connector Signal Name Signal Name +3.3V +3.3V +3.3V -12V Ground...
Front Panel Connector The front panel connector (PANEL1) provides a standard set of switch and LED connec- tors commonly found on ATX or micro-ATX cases. Refer to the table below for informa- tion: Signal Function Signal Function HD_LED_P Hard disk LED(+) FP PWR/SLP *MSG LED(+) HD_LED_N Hard disk LED(-) FP PWR/SLP *MSG LED(-)
Installing Hardware Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.
CPU Installation Procedure The following illustration shows CPU installation components. Install your CPU. Pull up the lever away from the socket and lift up to 90-degree angle. Locate the CPU cut edge (the corner with the pin hold noticeably missing). Align and insert the CPU correctly.
Installing Memory Modules This motherboard accomodates two memory modules. It can support two 240-pin 1.8V unbuffered DIMM, DDR2 800/667/533/400. The maximum memory capacity is 16 GB. DDR2 SDRAM memory module table Memory module Memory Bus DDR2 200 MHz DDR2 266 MHz DDR2 667 333 MHz DDR2 800...
Page 22
Table A: DDR2 (memory module) QVL (Qualified Vendor List) The following DDR2 400/533/667/800 memory modules have been tested and qualified for use with this motherboard. Type Size Vendor Model Name Hynix HYMP532U646-E3 AA 256MB NANYA NT256T64UH4A0F-5A DDR2 400 SAMSUNG M378T3253FG0-CCC 512MB Nanya NT512T64U88A0F-5A CL3...
Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive. About IDE Devices Your motherboard has two IDE channel interfaces (IDE1 & IDE2). Two IDE ribbon cables supporting four IDE devices is bundled with the motherboard.
Page 25
About SATA Connectors This motherboard features four SATA connectors supporting a total of four drives. SATA , or Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation.
Installing a Floppy Diskette Drive The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable. You can install a 5.25-inch drive or a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
Installing Add-on Cards The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabili- ties by adding hardware that performs tasks that are not part of the basic system.
Page 28
Follow these instructions to install an add-on card: Remove a blanking plate from the system case corresponding to the slot you are going to use. Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: AUDIO1: Front Panel Audio header This header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. Signal Name Function AUD_MIC Front Panel Microphone input signal AUD_GND Ground used by Analog Audio Circuits...
Page 30
CD_IN1: Analog audio input header Signal Name Function CD In right channel CD in_R Ground Ground CD In left channel CD in_L SATA1/2/3/4: Serial ATA connectors These connectors are use to support the new Serial ATA devices for the highest date transfer rates (1.5 Gb/s), simpler disk drive cabling and easier PC assembly.
Page 31
COM2: Onboard serial port header (optional) Connect a serial port extension bracket to this header to add a second serial port to your system. Signal Name Function NDCDB Data carry detect NSINB Serial Data In NSOUTB Serail Data Out NDTRB Data terminal ready Ground NDSRB...
Page 32
USB3/4: Front Panel USB header The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, there are two USB headers onboard. Use the auxiliary USB headers to connect the front- mounted ports to the motherboard. Signal Name Function USB Power...
Connecting I/O Devices The backplane of the motherboard has the following I/O ports: PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device. PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard. Parallel Port Use LPT to connect printers or other parallel communications (LPT) devices.
Chapter 3 Using BIOS About the Setup Utility The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the system’s configura- tion status and provides you with options to set system parameters.
Press DEL to enter SETUP Pressing the delete key accesses the BIOS Setup Utility: Phoenix-AwardBIOS CMOS Setup Utility: Standard CMOS Features Frequency/Voltage Control Advanced BIOS Features Load Fail-Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP/PCI Configurations...
Updating the BIOS You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing.
Standard CMOS Features This option displays basic information about your system. Phoenix-Award WorkstationBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Sun, Jan 1 2006 Item Help Time (hh:mm:ss) 4 : 36 : 58 Menu Level IDE Channel 0 Master [None] IDE Channel 0 Slave [None]...
Page 39
If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Choose the line that lists LBA for an LBA drive. IDE Channel 0/1 Master/Slave IDE/Extended IDE Drives (Auto) Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel.
Advanced BIOS Features This option defines advanced information about your system. Phoenix-Award WorkstationBIOS CMOS Setup Utility Advanced BIOS Features Removable Device Priority [Press Enter] Item Help Hard Disk Boot Priority [Press Enter] CPU Internal Cache [Enabled] Menu Level Quick Power On Self Test [Enabled] First Boot Device [Removable]...
Page 41
Hard Disk Boot Priority (Press Enter) Scroll to this item and press <Enter> to view the following screen: Phoenix-AwardBIOS CMOS Setup Utility Hard Disk Boot Priority 1. Bootable Add-in Cards Item Help Menu Level Use < > or < > to select a device, then press <+>...
Page 42
ATA 66/100 IDE Cable Msg. (Enabled) This item enables or disables the display of the ATA 66/100 Cable MSG. Typematic Rate Setting (Disabled) If this item is enabled, you can use the following two items to set the typematic rate and the typematic delay settings for your keyboard.
Advanced Chipset Features These items define critical timing parameters of the motherboard. You should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.
Page 44
CKE base power down mode (Enabled) When in power down mode, if all pages of the DRAMs associated with a CKE pin are closed, then these parts are placed in power down mode. Only pre-charge power down mode is supported, not active power down mode. CKE based powerdown (Per Channel) The DRAM channel is placed in power down when all chip selects associated with the channel are adle.
Page 45
LDT Bus Frequency (Auto) This item allows users to manually adjust the LDT Bus Frequency. PCIE Reset Delay (Disabled) This item enables or disables the PCIE reset delay. Press <Esc> to return to the Advanced Chipset Features page. UMA Frame Buffer Size (Auto) This item allows users to manually adjust the UMA frame buffer size, from 16MB to 128MB.
Integrated Peripherals These options display items that define the operation of peripheral components on the system’s input/output ports. Phoenix-Award WorkstationBIOS CMOS Setup Utility Integrated Peripherals Item Help South OnChip IDE Device [Press Enter] South OnChip PCI Device [Press Enter] Menu Level SuperIO Device [Press Enter] Init Display First...
Page 47
Primary/Secondary Master/Slave PIO (Auto) Each IDE channel supports a master device and a slave device. These four items let you assign the kind of PIO (Programmed Input/Output) was used by the IDE devices. Choose Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 0-4. Primary/Secondary Master/Slave UDMA (Auto) Each IDE channel supports a master device and a slave device.
Page 48
USB 2.0 Controller (Enabled) Enable this item if your system supports USB 2.0. USB Controller (Enabled) This item enables the USB controller. Leave this at the default “Enabled” if you want to connect USB devices to your computer. USB Legacy Support (Enabled) Use this item to enable or disable support for legacy USB devices.
Onboard Parallel Port (378/IRQ7) This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel port. Parallel Port Mode (SPP) Enables you to set the data transfer protocol for your parallel port. There are four options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port) and ECP+EPP.
Page 50
HDD Power Down (Disabled) The IDE hard drive will spin down if it is not accessed within a specified length of time. Options are from 1 Min to 15 Min and Disable. Video Off Option (Suspend —> Off) This option defines if the video is powered down when the system is put into suspend mode. Video Off Method (V/H SYNC+Blank) This item defines how the video is powered down to save power.
Page 51
Resume by PCI-E PME (Enabled) This system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Express card. You must use an ATX power supply inorder to use this feature. Use this item to do wake- up action if inserting the PCI Express card.
PNP/PCI Configurations These options configure how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the the ISA and PCI buses on the motherboard use system IRQs (Interrup ReQuests) and DMAs (Direct Memory Access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup utility for the motherboard to work properly.
PC Health Status On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds. Phoenix-Award WorkstationBIOS CMOS Setup Utility PC Health Status Item Help Smart Fan Function [Press Enter] Menu Level Shutdown Temperature [Disabled] Warning Temperature...
System Component Characteristics These fields provide you with information about the systems current operating status. You cannot make changes to these field. • CPU Vcore • VDIMM • • Voltage • VBAT • CPU Tcontrol • System Temperature • CPU/SYSTEM Fan Speed Frequency/Voltage Control This item enables you to set the clock speed and system bus for your system.
Load Fail-Safe Defaults This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility: Press <Y> and the <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The fail-safe defaults place no great demands on the system and are generally stable.
Save & Exit Setup Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <Y> to save and exit, or press <N> to return to the main menu. Exit Without Saving Highlight this item and press <Enter>...
Chapter 4 Using the Motherboard Software About the Software CD-ROM The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version.
Setup Tab Setup Click the Setup button to run the software installation program. Select from the menu which software you want to install. Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar.
Page 59
Click Next. The following screen appears: Check the box next to the items you want to install. The default options are recommended. Click Next run the Installation Wizard. An item installation screen appears: Follow the instructions on the screen to install the items. Drivers and software are automatically installed in sequence.
Manual Installation Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers.
Page 61
Caractéristiques Processeur La RS482M-M utilise un socket de AM2 ayant les caractéristiques suivantes : • Peut recevoir les processeurs AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual- Core/Athlon 64/Sempron • Prend en charge des vitesses d’interface HyperTransport (HT) allant jusqu’à 2000MT/s La Technologie HyperTransport est une liaison point à...
Page 62
Audio • Conforme aux spécifications AC’97 V2.3 • Prend en charge le CODEC audio 6 canaux destiné aux systèmes multi- média PC • Offre trois entrées stéréo de niveau de ligne analogique avec contrôle de volume 5 bits: Ligne d’entrée, CD, AUX •...
Page 63
Feature Prozessor Das RS482M-M verwendet einen AM2 Socket mit den folgenden Merkmalen: • Nimmt AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/Athlon 64/ Sempron Prozessoren auf • Unterstützt bis zu 2000MT/s HyperTransport (HT) Interface- Geschwindigkeiten HyperTransport Technologie ist ein Punkt-zu-Punkt Link zwischen zwei Geräten. Es ermöglicht integrierten Schaltkreisen einen Informationsaustausch mit wesentlich höherer...
Page 64
Audio • Entspricht AC’97 V2.3 Spezifikationen • Unterstützt 6-Kanal Audio CODEC, entwickelt für Multimedia PC-Systeme • Stellt drei analoge Line-Level Stereoeingänge mit 5-bit Lautstärkeregelung zur Verfügung: Line-in, CD, AUX • Entspricht den Microsoft WHQL/WLP 2.0 Audio-Anforderungen Erweiterungsoptionen Das Mainboard bietet die folgenden Erweiterungsoptionen: •...
Page 65
Caratteristiche Processore RS482M-M è dotata di una presa a AM2 che offre le seguenti caratteristiche: • Compatibilità con processori AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual- Core/Athlon 64/Sempron • Supporto di velocità di interfaccia HyperTransport (HT) fino a 2000 MT/s...
Page 66
Audio • Conforme alle specifiche AC’97 V2.3 • Supporto di CODEC audio a 6 canali per sistemi PC multimediali • Tre ingressi analogici stereo lineari con controllo volume a 5 bit: Line-In, CD, • Conforme ai requisiti audio di WHQL e WLP 2.0 di Microsoft Opzioni di espansione La scheda madre è...
Page 67
Característica Procesador La RS482M-M usa un zócalo AM2 que lleva las sigtes. características: • Acomoda procesadores AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/ Athlon 64/Sempron • Soporta hasta las velocidades de interfaz 2000MT/s HyperTransport (HT) La Tecnología HyperTransport es un vínculo punto a punto entre dos dispositivos, habilita circuitos integrados para intercambiar la información en velocidades más rápidas que las...
Page 68
Audio • Conformidad con las especificaciones AC’97 V2.3 • Soporta CODEC de audio de 6 canales diseñaods para los sistemas multimedia • Provee tres entradas en estéreo a nivel de línea análogicas con control de volumen de 5-bit: LIne-in, CD, AUX •...
Page 69
Características Processador O RS482M-M usa uma ficha de AM2 que comporta as seguintes características: • Acomoda processadores AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/ Athlon 64/Sempron • Suporta velocidades de interface de HyperTransportTM (HT) até 2000MT/s Tecnologia de HyperTransport Té...
Page 70
Áudio • Cumpre com as especificações AC’97 V2.3 • Suporta CODEC áudio com 6 canais concebido para sistemas multimédia para PC • Fornece três entradas estéreo nível de linha analógicas com controlo de volume de 5 bits: LIne-in, CD, AUX •...
Page 73
특성 프로세서 RS482M-M은 AM2 소켓을 사용하여 다음과 같은 기능을 제공합니다. • AMD 애슬론 64 FX/애슬론 64 X2 듀얼 코어/애슬론 64/샘프론 프로세서 사용 • HyperTransport (HT) 인터페이스 속도 최대 2000MT/s 지원 HyperTransport 기술은 두 장치간의 point-to-point 링크로, 집적 회로가 기존의 상호 연결 기술 보다 더 빠른 속도로 정보를 교환할 수 있다.
Page 74
오디오 • AC’97 V2.3 사양 부합 • PC 멀티미디어 시스템을 위해 디자인 된 6 채널 오디오 코덱 지원 • 5 비트 볼륨 컨트롤의 아날로그 라인 레벨 스테레오 입력 3개 : Line-in, CD, • 마이크로소프트 WHQL/WLP 2.0 오디오 요구 조건 부합 확장...
Page 79
Характеристики Процессор Плата RS482M-M использует AM2 сокет и обладает следующими характеристиками: Размещает процессоры AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual- • Core/Athlon 64/Sempron Поддерживает технологию 2000MT/s HyperTransport (HT) • Технология HyperTransport обеспечивает связь двух устройств по протоколу point- to-point, позволяя гораздо более быстрый обмен информацией между интегральными...
Page 80
Аудио • Совместимость со спецификацией AC’97 V2.3 • Поддерживает 6-канальный аудио CODEC для мультимедиальных компьютерных систем • Обеспечивает три аналоговых стереовхода с 5-битной регуляцией громкости: Line-in, CD, AUX • Соответствие требованиям для аудио Microsoft WHQL/WLP 2.0 Возможности расширения Существуют следуюшие опции расширения данной материнской платы: •...
Page 81
Cechy Procesor Płyta główna RS482M-M dostosowana jest do AM2 gniazda i posiada następujące właściwości: • Przystosowana do procesorów firmy AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/Athlon 64/Sempron • Obsługuje złącze HyperTransport (HT) z szybkością do 2000MT/s Technologia HiperTransportu jest protokołem komunikacji między dwoma urządzeniami, który umożliwia układom zcalonym wymieniać...
Page 82
Audio • Zgodne ze specyfikacją AC’97 w wersji 2.3 • Obsługuje 6 kanałów audio CODEC dla komputerowych systemów multimedialnych • Zapewnia trzy wejściowe, analogowe linie stereo z 5 bitową regulacją głośności: Line-in, CD, AUX • Spełnia wymagania stawiane audio przez firmę Microsoft w systemie WHQL/WLP 2.0 Możliwości rozbudowy Płyta głwna wyposażona jest w następujące gniazda:...
Page 83
Vlastnosti Procesor Základní deska RS482M–M využívá AM2 patici nabízející následující vlastnosti: • Podpora procesorů AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/Athlon 64/Sempron • Podpora rychlostí rozhraní HyperTransport (HT) až 2000 MT/s Technologie HyperTransport je přímým spojením mezi dvěma zařízeními, umožňující integrovaným obvodům výměnu informací...
Page 84
Zvuk • Splňuje požadavky standardu AC’97 V2.3 • Podpora 6kanálového zvukového kodeku určeného pro multimediální PC systémy • Nabízí tří analogové linkové stereo vstupy s 5bitovým řízení hlasitosti: LINE-IN, CD, AUX • Splňuje požadavky pro audio zařízení Microsoft WHQL/WLP 2.0 Možnosti rozšíření...
Page 85
Caracteristici Procesorul RS482M-M utilizează un soclu de AM2 de ace care are următoarele caracteristici: • Funcţionează cu procesoare AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual- Core/Athlon 64/Sempron • Suportă interfeţe HyperTransport (HT) cu viteze de până la 2000 MT/s Tehnologia HyperTransport este o legătură...
Page 86
Audio • Compatibil cu specificaţia AC’97 V2.3 • Suportă CODEC cu şase canale audio destinate sistemelor multimedia ale calculatoarelor • Oferă trei intrări audio analoge stereo, cu un control al volumului sonor de 5 biţi: Intrare audio, CD, AUX • Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0 Opţiuni de extindere Placa de bază...
Page 87
Спецификация Процесор RS482M-M използва сокет AM2 със следните спецификации: • Поддръжка на процесори AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual- Core/Athlon 64/Sempron • Поддръжка на технологията HyperTransport (HT) със скорост до 2000MT/s Технологията HyperTransport е връзка точка-до-точка (point-to-point) между...
Page 88
Аудио • Съвместимост със спецификацията AC’97 V2.3 • Поддръжка на 6-канален аудио кодек за мултимедийни компютърни системи • Три аналогови линейни стерео входа с 5-битов контрол на силата на звука: Line-in, CD, AUX • Съответствие с изискванията на Microsoft WHQL/WLP 2.0 Възможности...
Page 89
Jellemző Processzor Az RS482M-M AM2 socket-el rendelkezik, ennek jellemzői pedig a következők: • AMD AM2 AMD Athlon 64 FX/Athlon 64 X2 Dual-Core/Athlon 64/Sempron processzorokkal működik • Maximum 2000 MT/s HyperTransport (HT) sebességű interfészt támogat A HyperTransport technológia egy ponttól pontig való kapcsolat két készülék között, és segítségével az integrált áramkörök közötti információcsere sebessége sokkal nagyobb, mint a...
Page 90
Audio • Megfelel az AC’97 2.3-as specifikációnak • A számítógép multimédiás rendszereinek szánt hat csatornás audio CODEC- et támogat • Három analóg sztereo bemenetet biztosít 5 bites hangerő vezérléssel: bemenet, CD, AUX • Megfelel a Microsoft WHQL/WLP 2.0 audio követelményeine Bővítési lehetőségek Az alaplap a következő...