Related Manuals for Chicco Fit 4
Summary of Contents for Chicco Fit 4
- Page 1 4-in-1 Convertible Car Seat User Guide For future use,STORE USER GUIDE in compartment at rear of base. ©2019 Artsana USA, Inc. 09/09 IS0178E_04 www.chiccousa.com...
-
Page 2: Table Of Contents
Registration and Recall STAGE 1& 2 INSTALLATION Child Guidelines Stage 1 & 2 Rear-Facing Setup If you have any problems with your Chicco Child Restraint, Safe Use Checklist Install Using LATCH or any questions regarding installation or use, please call:... -
Page 3: Registration And Recall
REGISTRATION AND RECALL REGISTRATION AND RECALL Please complete the Registration Card that came with your Child Restraint and mail it promptly. Child Restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, e-mail address if available, and the restraint’s model number and manufacturing date to: Artsana USA, Inc. -
Page 4: Child Guidelines
CHILD GUIDELINES CHILD GUIDELINES See Select This Child Restraint is designed for children ages Birth to 10 years old. Stage 1 & Stage 2 ONLY use this Child Restraint if the child meets BOTH of the following Rear-Facing Weight and Height requirements: on page 24. -
Page 5: Safe Use Checklist
SAFE USE CHECKLIST SAFE USE CHECKLIST Ensure that the Child Restraint is properly leveled when installed: YOUR CHILD’S SAFETY DEPENDS ON YOU! You MUST follow the detailed instructions in this User Guide to ensure the steps below are performed correctly! STAGE 1 &... -
Page 6: Important Warnings
IMPORTANT WARNINGS IMPORTANT WARNINGS WARNING WARNING DEATH or SERIOUS INJURY CAN OCCUR DEATH or SERIOUS INJURY CAN OCCUR FAILURE TO FOLLOW THESE INSTRUCTIONS AND THE PRODUCT Secure Child Properly LABELS CAN RESULT IN SERIOUS INJURY OR DEATH TO YOUR CHILD. •... - Page 7 IMPORTANT WARNINGS IMPORTANT WARNINGS WARNING WARNING DEATH or SERIOUS INJURY CAN OCCUR DEATH or SERIOUS INJURY CAN OCCUR Install Child Restraint Correctly Install Child Restraint Correctly • ALWAYS use the top tether strap on this Child Restraint when installed FORWARD-FACING, if a tether •...
- Page 8 • DO NOT use any accessories, pads or products not included with this Child Restraint, unless PAGE INTENTIONALLY LEFT BLANK approved by Chicco USA. Doing so will void the warranty of this Child Restraint. • You MUST replace this Child Restraint if it has been involved in a crash, even if you cannot see visible damage.
-
Page 9: Best Practices
• Do not leave loose objects, such as books, bags, etc., in the back of the vehicle. In the event of a sharp turn, sudden stop, or crash, loose objects can be thrown around and • Contact Chicco, USA by visiting our website at www.chiccousa.com or possibly cause serious injury to vehicle occupants. -
Page 10: Child Restraint Components
CHILD RESTRAINT COMPONENTS CHILD RESTRAINT COMPONENTS Adjustment Handle (Head Rest) Tether Chest Clip Strap Bubble Level Tether Indicator Storage Harness Strap (Each Side) Forward-Facing Forward-Facing Lock-Off Crotch Shoulder Lock-Off Strap Pad Pads LATCH Harness Waist Belt Pad Connector LATCH (On Select Models) Release Button Storage Connector Storage... -
Page 11: Insert Components
INSERT COMPONENTS INSERT COMPONENTS INSERT STAGE USE: Positioner Stage 1 Stage 1 & 2 Headrest Insert Positioner Stage 2 & Headrest Insert Stage 1 Shoulder Belt Pad Stage 4 Stage 1 Positioner Stage 4 Shoulder Belt Pad Stage 2 Positioner... -
Page 12: Latch And Tether Components/Storage
LATCH AND TETHER COMPONENTS LATCH AND TETHER COMPONENTS TETHER: Tether Strap Tether Strap Adjuster Tether Hook Tether LATCH: LATCH LATCH Adjuster (PULL 1 st ) PULL PULL LATCH Tightener (PULL 2 nd ) PULL PULL ® SuperCinch LATCH Strap LATCH Connectors... - Page 13 LATCH AND TETHER STORAGE LATCH AND TETHER STORAGE Always make sure LATCH Components are properly stored in the compartments when not in use. LATCH STORAGE: Store each LATCH strap in the compartments located on either side of the Child Restraint base when not in use. Make sure Lower Anchor Connector Storage compartments are properly closed.
- Page 14 SELECT REAR-FACING MODE SELECT REAR-FACING MODE WARNING! REAR-FACING use of this Child Restraint is ONLY for REAR-FACING: STAGE 1 REAR - FACING children who meet ALL of the requirements shown here. If the child is STAGE 1: 4 – 16 lbs (1.8 – 7.3 kg) STAGE 2 REAR - FACING not within these requirements because the child is too large, review the STAGE 2: 12 –...
- Page 15 SELECT FORWARD-FACING MODE SELECT FORWARD-FACING MODE WARNING! FORWARD-FACING HARNESS MODE use of this Child FORWARD-FACING HARNESS MODE: STAGE 3 FORWARD - FACING Restraint is ONLY for children who meet ALL of the requirements shown here. 25 – 65 lbs (11.4 – 29.5 kg) HARNESS MODE If the child is not within these requirements because the child is too small, review the...
- Page 16 SELECT BOOSTER MODE SELECT BOOSTER MODE WARNING! BOOSTER MODE use of this Child Restraint is ONLY for BOOSTER MODE: children who meet ALL of the requirements shown here. If the child is not 40 – 100 lbs (18 – 45.3 kg) STAGE 4 FORWARD - FACING BOOSTER MODE within these requirements because the child is too small, review the...
-
Page 17: Cup Holder
CUP HOLDERS CUP HOLDERS WARNING - Do NOT use Cup Holder to hold hot liquids. PLASTIC CONTAINERS ONLY - No glass or metal containers. Only use cups with less than 12 oz. (355 ml) capacity. Never place sharp or pointed objects in Cup Holder. In a crash these objects could hit you or your child and cause serious injuries. -
Page 18: Crotch Strap Pad
CROTCH STRAP PAD CROTCH STRAP PAD When installing through the slot in the Stage 1 Positioner, Stage 2 Positioner or Seat Pad, make sure the Fabric Notches are tucked under the slot in the top layer of padding. The Crotch Strap Pad can be installed through the Seat Pad, Stage 1 Positioner or Stage 2 Positioner. -
Page 19: Adjusting Crotch Strap
ADJUSTING CROTCH STRAP ADJUSTING CROTCH STRAP Adjust Crotch Strap if strap is underneath child. When moving the child restraint from Stage 2 rear-facing mode to Stage 3 forward-facing mode, the crotch strap must be adjusted to the front position. Back Position Front Position Unbuckle Harness Straps. - Page 20 ADJUSTING CROTCH STRAP ADJUSTING CROTCH STRAP Slide the orange button on the Crotch Strap lock while pulling up on the Crotch Strap to open the compartment (a,b). Then pull the Crotch Strap forward or backward into desired position (c). Close the compartment by pushing down on the door until it locks back into place.
-
Page 21: Stage 1 Positioner
To ensure a better fit for smaller infants the Stage 1 Positioner may be needed. Do NOT use any other infant insert or pillows. Only use those provided by Chicco for this Child Restraint. Pull both Harness Straps over the side panels of Stage 1 Positioner. -
Page 22: Stage 1 & 2 Headrest Insert
STAGE 1 & 2 HEADREST INSERT Do NOT use any other infant insert or pillows. Only use those provided by Chicco for this Child Restraint. Fold over the Stage 1 & 2 Headrest side sections and insert both headrest flaps into the Headrest pockets, as shown. -
Page 23: Stage 2 Positioner
STAGE 2 POSITIONER Do NOT use any other infant insert or pillows. Only use those provided by Chicco for this Child Restraint. Raise the Headrest to the highest position. Pull up on the Headrest Adjustment Tab on the top of the Child Restraint Headrest. - Page 24 STAGE 2 POSITIONER STAGE 2 POSITIONER Fold over the Stage 2 Positioner side section and insert the flap into the seat back side pocket then attach the snap, as shown (a). Repeat for the other side section flap and snap (b). Attach the elastic strap on the front of the Stage 2 Positioner, pull the elastic strap under the front edge of the seat bottom and loop it around both hooks.
- Page 25 STAGE 4 SHOULDER BELT PAD STAGE 4 SHOULDER BELT PAD Remove the Stage 1 Positioner, the Stage 2 Positioner and the Stage 1 & 2 Headrest. Completely loosen Harness by pressing Harness Release Button on the front of the Child Restraint and pulling out on both of the Harness Straps as far as possible.
- Page 26 VEHICLE SEATING POSITIONS VEHICLE SEATING POSITIONS Some vehicles have no seating Do not use on a folded positions which are compatible down vehicle seat back. with this Child Restraint. If in doubt, contact the vehicle manufacturer for assistance. Only forward-facing vehicle seats should be used with this Child Restraint.
-
Page 27: Vehicle Seat Belts
VEHICLE SEAT BELTS RF AND FF VEHICLE SEAT BELTS RF AND FF The following types of vehicle belts MUST NOT be used to install this Child Restraint. The information in this section applies to installation with REAR-FACING If any of the belt types listed below are in the chosen seating position, choose another FORWARD-FACING HARNESS MODE vehicle seat belts only. - Page 28 VEHICLE SEAT BELTS - BOOSTER VEHICLE SEAT BELTS - BOOSTER The following types of vehicle belts MUST NOT be used to install this Child The information in this section only applies to installation with vehicle seat belts Restraint in BOOSTER MODE.
-
Page 29: What Is Latch
WHAT IS LATCH? WHAT IS LATCH? Vehicle Top Tether Anchor Points WARNING: This Child Restraint is designed to be used with lower anchors at the standard spacing (11 inches (28 cm)) ONLY! Refer to vehicle owner’s manual for information about LATCH and Child Restraint installation positions. -
Page 30: What Is A Tether
WHAT IS A TETHER? WHAT IS A TETHER? The tether is a strap on your child restraint that connects to a tether anchor in your vehicle. Tether anchor locations vary Vehicle Roof from vehicle to vehicle. Check your vehicle owner’s manual and look for the tether anchor symbol as shown. - Page 31 REAR-FACING SETUP REAR-FACING SETUP Infants may have difficulty breathing when in a sitting Do not use Tether in REAR-FACING mode. Tether must be properly stored - See “ Tether Storage” page 22. position. Make sure the seat is reclined properly so that your child’s head does not fall forward.
- Page 32 REAR-FACING SETUP REAR-FACING SETUP Place Child Restraint rear-facing on selected vehicle seat. Make sure it is not blocking the vehicle belt buckle. Push the Child Restraint back until Stage 1 it touches the vehicle seat back and make sure the base stays flat on the L E V E L vehicle seat.
-
Page 33: Install Using Latch
INSTALL USING LATCH INSTALL USING LATCH Do not use the lower anchors of the Child Restraint anchorage system (LATCH system) to attach this Child Restraint when restraining a child weighing Make sure more than 35 lbs (15.9 kg) with the internal harness of the Child Restraint. ®... - Page 34 INSTALL USING LATCH INSTALL USING LATCH Grab both ends of LATCH straps. Slide LATCH strap to blue REAR-FACING opening on both sides. Note: Both LATCH Connector Storage compartments must be open and both LATCH straps must be loosened to their full length in order to slide LATCH straps into position.
- Page 35 INSTALL USING LATCH INSTALL USING LATCH Locate the LATCH anchor bars in your vehicle. Attach both LATCH Do not install by this method for a child weighing Connectors to the vehicle LATCH bars. more than 35 lbs (15.9 kg). Pull up on the end of the LATCH Adjuster strap (Pull 1 st ) until strap is tight.
-
Page 36: Install Using Lap-Shoulder Belt
INSTALL USING LAP-SHOULDER BELT INSTALL USING LAP-SHOULDER BELT Route vehicle lap-shoulder belt through the blue REAR-FACING seat belt path on the side of Child Restraint (a). Pull the Stage 2 Positioner to the side and locate the opening in the seat pad (b). With your right hand guide the vehicle lap-shoulder belt UNDER the seat pad. - Page 37 INSTALL USING LAP-SHOULDER BELT INSTALL USING LAP-SHOULDER BELT While pushing down on the Child Restraint (a) pull the vehicle shoulder belt (b) to tighten vehicle lap belt. While still pulling the shoulder belt tight, slide the vehicle shoulder belt into the Lock-Off. Always use the Lock-Off on the opposite side of the vehicle belt buckle.
-
Page 38: Install Using Lap Belt Only
INSTALL USING LAP BELT ONLY INSTALL USING LAP BELT ONLY Route vehicle lap belt through the blue REAR-FACING seat belt path on the side of Child Restraint (a). Pull the Stage 2 Positioner to the side and locate the opening in the seat pad (b). With your right hand guide the vehicle lap belt UNDER the seat pad. - Page 39 INSTALL USING LAP BELT ONLY INSTALL USING LAP BELT ONLY While pushing down on the Child Restraint (a) pull the loose end of the vehicle lap belt (b) to tighten belt. CHECK YOUR WORK Hold Child Restraint at each side near REAR-FACING vehicle belt paths. Pull side to side and forward.
- Page 40 FORWARD-FACING SETUP FORWARD-FACING SETUP Before placing the Child Restraint in the vehicle, remove Tether from the tether compartment. If a tether anchor is not available, the Tether TILT should be stored properly. See page 48 for “Vehicle Seating Positions” before installing. Make sure the vehicle is on a level surface, if possible.
- Page 41 FORWARD-FACING SETUP FORWARD-FACING SETUP Place Child Restraint facing forward on selected vehicle seat. Make sure it is not blocking the vehicle belt buckle. Lay Tether Strap over the back L E V E L of the vehicle seat. Push the Child Restraint back until it touches the vehicle seat back and make sure the base stays flat on the vehicle seat.
-
Page 42: Install Using Latch
INSTALL USING LATCH INSTALL USING LATCH ® Make sure LATCH Make sure SuperCinch Do not use the lower anchors of the Child Restraint anchorage system Adjuster strap (Pull 1 st ) LATCH Tightener strap (LATCH system) to attach this Child Restraint when restraining a child weighing is loosened to the full (Pull 2 nd ) is loosened to length. - Page 43 INSTALL USING LATCH INSTALL USING LATCH When not accessing the LATCH or changing the belt path ALWAYS keep LATCH Connector Storage compartments closed. Locate the LATCH bars in your vehicle. Attach both LATCH Connectors PULL PULL to the vehicle LATCH anchor bars. Pull up on the end of the LATCH Adjuster strap (Pull 1 st ) until strap is tight.
- Page 44 INSTALL USING LATCH INSTALL USING LATCH Locate Tether anchor in your vehicle. Attach Tether Hook. Pull Tether Adjuster strap to tighten. CHECK YOUR WORK Hold Child Restraint at each side near FORWARD-FACING vehicle belt path. Pull side to side and forward. Child Restraint should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
-
Page 45: Install Using Lap-Shoulder Belt
INSTALL USING LAP-SHOULDER BELT INSTALL USING LAP-SHOULDER BELT Route vehicle lap-shoulder belt through the red FORWARD-FACING seat belt path on the side of Child Restraint. Lift the padding on the back of the seat and pull the vehicle belt through the opening on the side of Child Restraint. - Page 46 INSTALL USING LAP-SHOULDER BELT INSTALL USING LAP-SHOULDER BELT While pushing down on the Child Restraint (a) pull the vehicle shoulder belt (b) to tighten vehicle lap belt. While still pulling the shoulder belt tight, slide the vehicle shoulder belt into the Lock-Off. Always use the Lock-Off on the opposite side of the vehicle belt buckle.
- Page 47 INSTALL USING LAP-SHOULDER BELT INSTALL USING LAP-SHOULDER BELT Locate Tether anchor in your vehicle. Attach Tether Hook. Pull Tether Adjuster strap to tighten. CHECK YOUR WORK Hold Child Restraint at each side near FORWARD-FACING vehicle belt path. Pull side to side and forward. Vehicle belt should remain tight and Child Restraint should not move more than 1”...
-
Page 48: Install Using Lap Belt Only
INSTALL USING LAP BELT ONLY INSTALL USING LAP BELT ONLY Route vehicle lap belt through the red FORWARD-FACING seat belt path on the side of Child Restraint. Lift the padding on the back of the seat and pull the vehicle belt through the opening on the side of the Child Restraint. - Page 49 INSTALL USING LAP BELT ONLY INSTALL USING LAP BELT ONLY While pushing down on the Child Restraint (a) pull the loose end of the vehicle lap belt (b) to tighten. Locate Tether anchor in your vehicle. Attach Tether Hook. Pull Tether Adjuster strap to tighten.
- Page 50 SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS For a better fit in the Child Restraint with smaller infants, the Stage 1 Positioner, Stage 2 Positioner and Stage 1 & 2 Headrest provided may be needed. See page 38-42 for more details. Additionally, waist belt pads, crotch strap pad, and shoulder pads may need to be removed.
- Page 51 SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS Place child in Child Restraint with child’s back flat against the back of the seat. Pull Harness Straps over the child’s shoulders and around the child’s waist. Make sure there are no twists in Harness Strap. Clothing, such as bulky winter coats that interfere with the proper placement or adjustment of the Harness system should never be used.
-
Page 52: Securing Child With Harness
SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS Adjust Harness Strap height position up or down by pulling up on the Headrest Adjustment Tab on the top of the Child Restraint Headrest. Position the Harness Straps at or just above the child’s shoulders. Make sure Head Rest locks into position before tightening Harness. - Page 53 SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS Insert each Buckle Tongue into Harness Buckle; listen for a click (a). Pull up firmly on both Buckle Tongues to make sure that they are securely latched (b). “CLICK”...
- Page 54 SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS Fasten Chest Clip by snapping both sides together; listen for a click. Harness straps must fit snugly and lay flat on the center of your child’s shoulders. Push Chest Clip and Shoulder Pads down away from the child’s neck and towards the Harness Buckle.
- Page 55 SECURING CHILD WITH HARNESS SECURING CHILD WITH HARNESS Tighten the harness by pulling slowly on Harness Adjustment Strap until the harness is snug on child (a). If you can pinch a fold in the strap at the child’s shoulders, harness is too loose (b). If the harness is too loose pull the Harness Adjustment strap more.
-
Page 56: Securing Child Checklist
SECURING CHILD CHECKLIST SECURING CHILD CHECKLIST Check the position of Chest Clip: Chest Clip should be centered on the child’s chest, level Harness Straps must be snug. If you can pinch a fold in with the armpits. the strap, the harness is too loose. A snug strap should not allow any slack. - Page 57 BOOSTER MODE SETUP BOOSTER MODE SETUP Store the Harness Straps and Crotch Strap properly when using the Child Restraint in BOOSTER MODE. Remove the Stage 1 Positioner, the Stage 2 Positioner and Stage 1 & 2 Headrest. Completely loosen Harness by pressing Harness Release Button on the front of the Child Restraint and pulling out on both of the Harness Straps as far as possible.
- Page 58 BOOSTER MODE SETUP BOOSTER MODE SETUP Undo both snap buttons on the lower Backrest Seat Pad and pull forward. Connect the Chest Clip together and slide it down to the buckle tongues. Insert the Chest Clip and the buckle tongues into the compartment at the bottom of the Seat Back.
- Page 59 BOOSTER MODE SETUP BOOSTER MODE SETUP Remove the Crotch Strap from the slot and pull forward on the Seat pad to locate the Crotch Strap compartment below. To store the Crotch Strap, fit the Crotch Strap buckle into the Crotch Strap compartment with the release button facing up.
- Page 60 BOOSTER MODE SETUP BOOSTER MODE SETUP Repeat Booster Seat Setup Steps 2-3 (on pages 110-112) in REVERSE to re-attach the Backrest Seat Pads. If using Higher Head Rest/Harness Position, make sure the seat back padding panel is folded down.
- Page 61 BOOSTER MODE INSTALLATION BOOSTER MODE INSTALLATION See page 48 for “Vehicle Seating Positions” before installing. Make sure the vehicle is on a level surface, if possible. LEVEL Place the Booster Seat on the vehicle seat making sure the Seat Base is PARALLEL with the vehicle seating surface.
- Page 62 BOOSTER MODE INSTALLATION BOOSTER INSTALLATION BOOSTER MODE INSTALLATION Make sure the Child Restraint is not blocking the vehicle belt buckle. Stage 4 Installation on a Level Surface: Locate the Bubble Level Indicator L E V E L label and re-adjust the seat recline to any position that the Bubble falls between the STAGE 4 lines.
- Page 63 BOOSTER MODE INSTALLATION BOOSTER MODE INSTALLATION Use of LATCH and Top Tether in BOOSTER MODE is completely optional. If LATCH and Tether is not used, make sure the LATCH and Tether Straps are properly stored. See page 22. If using LATCH and Top Tether, locate the Tether compartment (see page 76) and PULL PULL LATCH Connector Storage compartment (see page 80) and remove the straps.
- Page 64 SECURING CHILD IN BOOSTER MODE SECURING CHILD IN BOOSTER MODE Place the child into the Child Restraint, making sure the child is sitting with his/her back against the Backrest. The Shoulder Belt guide must be positioned at or just slightly above the child’s shoulders.
- Page 65 SECURING CHILD IN BOOSTER MODE SECURING CHILD IN BOOSTER MODE Route the lap shoulder belt across the child’s thighs and chest, as shown. Buckle the vehicle belt. “CLICK”...
- Page 66 SECURING CHILD IN BOOSTER MODE SECURING CHILD IN BOOSTER MODE Slide the shoulder belt between the Headrest and the side of the Seat back (5a). Thread the shoulder belt through the orange Shoulder Belt Guide (5b), located at the bottom of the headrest. Make sure the Shoulder belt lays flat and is not twisted (5c).
- Page 67 CONVERT TO STAGE 1 & 2, OR STAGE 3 CONVERT TO STAGE 1 & 2, OR STAGE 3 To convert the STAGE 4 BOOSTER back to STAGE 1 & 2 REAR FACING STAGE 3 FORWARD-FACING position. Lift the top Backrest Seat Pad out of the way.
- Page 68 SECURING CHILD CHECKLIST SECURING CHILD CHECKLIST Slide the shoulder belt through the orange Shoulder Belt Guide. ALWAYS check to make sure vehicle seat belt is securely buckled. If buckle separates, child could be killed or seriously injured. Do not let your child slide forward or downward while in the Booster Seat. ...
-
Page 69: Installation On An Aircraft
INSTALLATION ON AN AIRCRAFT When traveling by airplane with your child, Chicco recommends taking the Child Restraint on the airplane with you so that you can use it with your child. Not only will it protect your child during take-off, landing, and turbulence, it will also allow your child to be more comfortable. - Page 70 CLEANING AND MAINTENANCE CLEANING AND MAINTENANCE REMOVING SHOULDER PADS: Unhook the hook and loop and remove Shoulder Pads as shown. INSTALL SHOULDER PADS: Re-attach Shoulder Pads by folding the hook and loop Tab over the Harness Strap (a). Secure both hook and loop Tabs together (b). Make sure they are oriented as shown (c).
- Page 71 INSTALL CROTCH STRAP: Reverse the removing instructions above to reinstall. DO NOT USE Child Restraint if any part of the harness is damaged. For proper removal and installation of the harness straps visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
-
Page 72: Cleaning And Maintenance
Sponge clean using warm water and mild soap. Towel dry. For softgood removal instructions visit the Chicco website at Do NOT remove LATCH or Adjuster straps. For additional information visit the Chicco www.chiccousa.com or call 1-877-424-4226. website at www.chiccousa.com or call 1-877-424-4226. - Page 73 PMS 2747and CMYK Gradient Learn how to INSTALL & USE in all 4 STAGES fit4stages.com...