Technical Data - Graco XM Series Operation Manual

Technical Data

Technical Data
Mixed ratio range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1:1-10:1 (in 0.1 increments)
Ratio tolerance range (before alarm). . . . . . . . . . . . . . . . . . . +/- 5%
Flow rates
Minimum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid viscosity range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-20,000 cps (heavier viscosities can be mixed using heat,
Fluid filtration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mesh, (238 micron) standard on pump outlets (filter
Air inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 npt(f)
Fluid inlets without feed kits. . . . . . . . . . . . . . . . . . . . . . . . . . 1 1/4 npt(m)
Maximum fluid working pressure of mixed material
50:1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum fluid temperature . . . . . . . . . . . . . . . . . . . . . . . . . 160° F (71° C)
Air supply pressure range . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-150 psi (0.35-1.0 MPa, 3.5-10.3 bar)
Maximum pump air set pressure
50:1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70:1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum pump inlet fluid feed pressure . . . . . . . . . . . . . . . . 250 psi (1.7 MPa, 17 bar)
Maximum air consumption at 100 psi (0.7 MPa, 7.0 bar)
3
in scfm (m /min.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 scfm per gpm (1.96 m
Air filtration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 micron main filter, 5 micron control air filter; see Pump
Ambient temperature range
Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental conditions rating . . . . . . . . . . . . . . . . . . . . . . Indoor/outdoor use
Sound pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 dBA at 100 psi (0.7 MPa, 7 bar)
Sound power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 dBA at 100 psi (0.7 MPa, 7 bar)
Wetted parts
Suction tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flush pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pumps (A and B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metering valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spray gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dimensions, page 80
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Base sprayer (XM1A00 and XM5A00 models)
* Minimum flow rate is dependent on material being sprayed and mixing capability. Test your material specific to flow rate.
84
1 qt./min. (0.95 liter/min.)*
3 gal./min/ (11.4 liter/min.)
circulation, and/or pressure feeding)
assembly not included on some models); alternative 30
mesh screens included
5200 psi (35.8 MPa, 358 bar)
6300 psi (43.5 MPa, 435 bar)
100 psi (0.70 MPa, 7.0 bar)
90 psi (0.62 MPa, 6.2 bar)
3
Performance Charts, page 83
32-130° F (0-54° C)
30-160° F (-1-71° C)
Altitude up to 4000 m
Maximum relative humidity to 99% up to 130° F (54° C)
Pollution degree (11)
Installation category (2)
aluminum
carbide, PTFE, stainless steel, UHMWPE
nylon
carbon steel, alloy steel, 303, 440, 17-ph grades stainless
steel, zinc and nickel plating, ductile iron, tungsten carbide,
PTFE
carbon steel, nickel plating, carbide, polyethylene, leather
carbon steel, nickel plating, carbide, 302 stainless steel,
PTFE, UHMWPE
stainless steel housing with acetal elements
Refer to spray gun manual
742 lbs (336.87 kg)
(Add component weights to base sprayer weight for your
specific model weight.)
/min. per lpm)
312359J