Jacuzzi J-400 Series Installation Manual And Use & Maintenance page 64

From the Settings Menu, tap
& Filter" menu tab in Orange. Tap
menu. The select one of the heating settings.
Auto heating:
When programmed to "Auto," the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (
Econo heating:
This is an energy saving heating program that allows the spa to
heat during non-peak hours. When programmed to "Econo, " the
spa will only be allowed to heat the water between 5:00 PM to
7:00 AM every day of the week. The hours cannot be adjusted.
To select this mode, tap (
Day heating:
When programmed to "Day," the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (
I
Programming the Primary Filter
To access the "Primary Filter" feature, tap
Filter" menu, to enter the "Primary Filter" programming.
Heat & Filter
Auto
Econo
Day
1 Filter 2
During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to keep
this setting, then you can skip this section.
In extreme bitter cold weather we recommend you pro-
gram the circulation pump to run 24 hours. Refer to the
"Winterizing" section.
Any time the circulation pump runs outside of a program cycle,
e.g. for heating, that run time will be deducted from the next
primary filter cycle. For example, the primary filter cycle is set
to 8 hours every 24 hours but the circulation pump comes on
for 2 hours to heat the water after the cycle has finished. The
next primary filter cycle will only be for 6 hours not 8 hours.
To change the default cycle:
Primary Filter
Start
12pm
12
pm
End
8pm
or to highlight the "Heat
to the enter the
Heat & Filter
next to the "Auto" icon.
)
) next to the "Econo" icon.
next to the "Day" icon.
)
from the "Heat &
1
Primary Filter
Start
12pm
12
pm
End
8pm
When you enter the menu, "Start" and "12" will be highlighted.
Tap or to change the hour in 1-hour increments. To
switch from "AM" to "PM" you must round a 12-Hour period.
Tap to accept the change. Tap
time for the cycle.
Tap the hour block to change the end time. Tap
to change the hour in 1-hour increments. To switch from "AM"
to "PM" you must round a 12-Hour period.
Tap to confirm and save your changes. Tap
the Heat & Filter Menu. Tap again to return to the Settings Menu.
Summer Logic: In warm weather, the water temperature in the spa
may exceed the set temperature. This condition may occur due to
heat transference from the filter/circulation pump and jets pumps. If
the water temperature is higher than 35°C (95°F) and rises two de-
grees above the set temperature, a "Summer Logic" condition occurs
that deactivates the filter/circulation pump and CLEARRAY®. This sa-
fety feature cannot be altered! The filter/circulation pump and
CLEARRAY® will remain off until the water temperature cools to the
set temperature (except between 9am-11am when the fil-
ter/circulation pump runs for it's mandatory 2 hour cycle.) To help
prevent a "Summer Logic" condition, it may be necessary to reduce
filter/circulation pump cycles run times in warm weather.
I
Programming the Secondary Filter
To access the "Secondary Filter" feature, tap
& Filter Menu, to enter the "Secondary Filter" programming. Du-
ring a secondary filtration, the Jets Pump 1 is activated. There
are 3 cycles you can select from. The factory default cycle is
"Away Mode. " If you elect to keep this setting, then you can skip
this section.
Heat & Filter
Auto
Econo
Day
1 Filter 2
Indicates that the feature is active.
feature is not active.
To change the Secondary Filter cycle:
Away Mode: Secondary Filtration is disabled. To activate this
mode, tap ( ) next to the "Away" icon.
Note: This is the factory default setting.
Infrequent Mode: Activates two cycles at 8:00 PM and 8:00 AM
every other day. Each cycle will last 10 minutes for a total of 20
minutes every other day. To activate this mode, tap (
to the "Infrequent" icon. Time and duration cannot be altered.
Frequent Mode: Activates two cycles at 8:00 PM and 8:00 AM e-
very day. Each cycle will last 10 minutes for a total of 20 minu-
tes every day. To activate this mode, tap (
quent" icon. Time and duration cannot be altered.
Tap to return to the Heat & Filter Menu. Tap again to return
to the Settings Menu.
64
End
to program the end
or
to return to
from the Heat
2
Secondary Filter
Infrequent
Frequent
Away
Indicates that the
next
)
) next to the "Fre-