Delete - Roland BK-9 Owner's Manual

Rhythm Composer
1.
Use the dial to edit the following parameters.
Parameter Setting
ADrums~Acc6,
Track
ALL
Mode Major, Minor, 7th
Intro 1~4, Main
1~4, Fill Dwn 1~3,
Division
Fill Up 1~3, End
1~4
1~[last measure
From Bar of the track or
pattern]
1~[number of
From Beat
beats per bar]
From CPT 0~119
1~[last measure
To Bar of the track or
pattern]
1~[number of
To Beat
beats per bar]
To CPT 0~119
110
Right Display
Explanation
Allows you to select the track you
wish to edit. You can also select "ALL"
here, in which case the operation
applies to all tracks.
Allows you to select the Mode to be
edited.
Use this parameter to select the
Division you want to edit.
Refers to the first measure to be
edited. By default, the "From" value is
set to the beginning of the selected
track(s).
Specifies the beat position. The
number of selectable beats depends
on the selected time signature.
Refers to the starting CPT position.
"CPT" is short for "Clock Pulse Time",
the smallest unit used by the BK-9.
(There are 120 CPTs to every beat of
a 4/4 bar.) Change this setting only if
your edit operation should start after
the selected beat.
This is where you specify the last
measure to be edited. By default, the
"To" position is set to the last event of
the selected track (or the last event
of the longest track when you select
"All").
Specifies the beat position.
The number of selectable beats
depends on the selected time
signature.
Refers to the last clock that should be
affected by the edit operation.
Change this setting only if your edit
operation should not end exactly on
the selected beat.
Parameter Setting
ALL
Note
Modulation
PanPot
Expression
Reverb
Data Type
(select the
data to be
edited)
Chorus
Program Change
P.Bender:
From Note 0 C-~127 G9
To Note 0 C-~127 G9
2.
Press the [WRITE] button (its indicator flashes) to confirm
your settings and edit the data.
The display briefly confirms the operation and then returns to the
current Composer page.

Delete

Unlike the "Erase" function, "Delete" not only erases the data but
also the measures, beats and/or CPT units, so that all data that lie
behind the "To" position are shifted towards the beginning of the
track(s). You cannot choose the data type to be erased.
1.
Use the dial to edit the following parameters.
Parameter Setting
ADrums~Acc6,
Track
ALL
Mode Major, Minor, 7th
Explanation
All parameters listed below.
Only note messages.
CC01 messages usually used for add-
ing vibrato (i.e. use of the BENDER/
MODULATION lever).
CC10 messages that specify the
stereo position.
CC11 messages that are used for
temporary volume changes.
Reverb Send messages (how strongly
the part should be processed by the
reverb effect).
Chorus Send messages (how strongly
the part should be processed by the
chorus effect).
Program change messages, used to
select sounds or Drum Sets.
NOTE
By deleting program change
messages you also dispose of the
related CC00 and CC32 (bank select)
messages.
Pitch Bend data (i.e. use of the
BENDER/MODULATION lever).
This parameter is only displayed
if "Data Type" (see above) is set to
"Note". It allows you to set the note
(or lower limit of the note range)
to be modified within the specified
"From/To" time range.
This parameter allows you to set
the upper limit of the note range
to be modified within the specified
"From/To" time range.
Right Display
Explanation
Allows you to select the track you wish to
edit. You can also select "ALL" here, in which
case the operation applies to all tracks.
Allows you to select the Mode to be edited.