Chorus - Boss GT-1000 Parameter Manual

Effect
TWIST
Parameter Value Explanation
Rotation stops when you switch TRIGGER from
RISE 0 FALL
ON to OFF.
MODE
When you switch TRIGGER from ON to OFF, fade-
RISE 0 FADE
out occurs while continuing the rotation.
The TWIST effect is applied when you turn this
TRIGGER OFF, ON
ON.
This parameter adjusts the amount of time it is to
RISE TIME 0–100
take for the effect to transition to the maximum.
This parameter adjusts the amount of time it is to
FALL TIME 0–100
take for the effect to transition to the original.
LEVEL 0–100 Adjusts the volume of the effect sound.
SPACE ECHO
Parameter Value
1, 1+2, 1+3, 2+3,
HEAD
1+2+3
WOW &
0–100
FLUTTER
TAPE ECHO PX
Parameter Value
WOW &
0–100
FLUTTER
BIN DRUM ECHO
Parameter Value
1, 2, 3, 4, 1+2,
2+3, 3+4, 1+3,
HEAD
2+4, 1+2+3,
2+3+4, 1+2+3+4
ECHO, REPEAT,
SELECTOR
SWELL
WOW &
0–100
FLUTTER
10
Explanation
Selects the combination playback heads.
Playback heads 2/3 provide delay times
that are two times or three times as long as
playback head 1.
Adjusts the wow & flutter.
Explanation
Adjusts the wow & flutter.
Explanation
Selects the combination playback heads.
Selects the operating mode of the delay.
Depending on mode that's selected, the
FEEDBACK will not work in some cases.
Adjusts the wow & flutter.

CHORUS

In this effect, a slightly detuned sound is added to the original sound
to add depth and breadth.
COMMON
Parameter Value
ON/OFF OFF, ON
Selection for the chorus mode.
MONO
STEREO 1
TYPE
STEREO2
DUAL
0–100,
RATE
BPM ΠР`
DEPTH 0–100
PRE-DELAY
0.0ms–40.0ms
EFFECT LEVEL 0–100
TRI
WAVEFORM
SINE
FLAT,
LOW CUT
20.0Hz–20.0kHz
20.0Hz–20.0kHz,
HIGH CUT
FLAT
DIRECT LEVEL 0–100
BPM 40–250
Explanation
Turns this effect on/off.
This chorus effect outputs the same sound
from both L channel and R channel.
This stereo chorus uses spatial synthesis,
with the direct sound output in the L
channel and the effect sound output in the
R channel.
This is a stereo chorus effect that adds
different chorus sounds to L channel and R
channel.
This lets you apply chorus independently to
the L and R channels.
Adjusts the rate of the chorus effect.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified for
each patch. This makes it easier to achieve
effect sound settings that match the
tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it is
then synchronized to a period either 1/2
or 1/4 of that time.
Adjusts the depth of the chorus effect.
* To use it for doubling effect, set the value
to 0.
Adjusts the time needed for the effect sound
to be output after the direct sound has been
output. By setting a longer pre delay time,
you can obtain an effect that sounds like
more than one sound is being played at the
same time (doubling effect).
Adjusts the volume of the effect sound.
Produces a typical chorus effect.
Produces a deeper sense of modulation.
This sets the frequency at which the low
cut filter begins to take effect. When FLAT is
selected, the low cut filter will have no effect.
This sets the frequency at which the high
cut filter begins to take effect. When FLAT
is selected, the high cut filter will have no
effect.
Adjusts the volume of the direct sound.
Setting this to 0 cuts the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that occur
each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI devices
tempo, making it impossible to set the
MASTER BPM. To enable setting of the
MASTER BPM, set "SYNC CLOCK" (p. 41) to
"INTERNAL. "