Pan; Phaser - Boss GT-1000 Parameter Manual

Effect

PAN

With the volume level of the left and right sides alternately changing,
when playing sound in stereo, you can get an effect that makes the
guitar sound appear to fly back and forth between the speakers.
Parameter Value
0–100,
RATE
BPM ΠР`
DEPTH 0–100
WAVEFORM 0–100
EFFECT LEVEL 0–100
DIRECT MIX 0–100
BPM
40–250

PHASER

By adding varied-phase portions to the direct sound, the phaser effect
gives a whooshing, swirling character to the sound.
Parameter Value
Selects the PHASER type.
PRIME
TYPE
SCRIPT
2, 4, 8, 16,
STAGE *1
24STAGE
0–100,
RATE
BPM ΠР`
DEPTH 0–100
RESONANCE *1
0–100
MANUAL *1 0–100
18
Explanation
Adjusts the frequency (speed) of the
change.
* When set to BPM, the value of each
parameter will be set according
to the value of the "MASTER BPM"
specified for each patch. This makes
it easier to achieve effect sound
settings that match the tempo of
the song.
* If, due to the tempo, the time is
longer than the range of allowable
settings, it is then synchronized to a
period either 1/2 or 1/4 of that time.
Adjusts the depth of the effect.
Adjusts changes in volume level.
A higher value will steepen wave's
shape.
Adjusts the volume.
Adjusts the volume of the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that
occur each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI
devices tempo, making it impossible
to set the MASTER BPM. To enable
setting of the MASTER BPM, set
"SYNC CLOCK" (p. 41) to "INTERNAL. "
Explanation
An original BOSS phaser. This provides
modulation that is not obtainable from
previous units.
Models the MXR Phase 90 which was
manufactured during the '70s.
Selects the number of stages that the phaser
effect will use.
This sets the rate of the phaser effect.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified
for each patch. This makes it easier to
achieve effect sound settings that match
the tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it is
then synchronized to a period either 1/2
or 1/4 of that time.
Determines the depth of the phaser effect.
Determines the amount of resonance
(feedback). Increasing the value will
emphasize the effect, creating a more
unusual sound.
Adjusts the center frequency of the phaser
effect.
Parameter Value
WAVEFORM *1 TRI, SINE
OFF, 0–100,
STEP RATE *1
BPM ΠР`
BI-PHASE *1 OFF, ON
0, 15, 30, 45,
60, 75, 90, 105,
SEPARATION *1
120, 135, 150,
165, 180
LOW DAMP *1 -100–0
HIGH DAMP *1
-100–0
FLAT,
LOW CUT *1 20.0Hz–
20.0kHz
20.0Hz–
HIGH CUT *1 20.0kHz,
FLAT
DIRECT MIX 0–100
BPM 40–250
*1 Setting available when TYPE is set to PRIME.
Explanation
Selects the type of wave.
This sets the cycle of the step function that
changes the rate and depth. When it is set
to a higher value, the change will be finer.
Set this to "Off" when not using the Step
function.
* When set to BPM, the value of each
parameter will be set according to the
value of the "MASTER BPM" specified
for each patch. This makes it easier to
achieve effect sound settings that match
the tempo of the song.
* If, due to the tempo, the time is longer
than the range of allowable settings, it is
then synchronized to a period either 1/2
or 1/4 of that time.
Specifies whether the two phase shift
circuits are connected in series (ON) or not
(OFF).
Adjusts the diffusion. The diffusion increases
as the value increases.
Adjusts the amount of feedback for the low-
frequency region.
Adjusts the amount of feedback for the
high-frequency region.
This sets the frequency at which the low
cut filter begins to take effect. When FLAT
is selected, the low cut filter will have no
effect.
This sets the frequency at which the high
cut filter begins to take effect. When FLAT
is selected, the high cut filter will have no
effect.
Adjusts the volume of the direct sound.
Adjusts the BPM value for each patch.
* BPM (beats per minute) indicates the
number of quarter note beats that occur
each minute
* When you have an external MIDI
device connected, the MASTER BPM
synchronizes to the external MIDI devices
tempo, making it impossible to set the
MASTER BPM. To enable setting of the
MASTER BPM, set "SYNC CLOCK" (p. 41) to
"INTERNAL. "