Boss GT-1000 Parameter Manual page 30

MENU
Parameter Value
PATCH CHANGE
EXP1 PDL-LOW
EXP1 PDL-MID
EXP1 PDL-HIGH
EXP1 SW
NUM1–NUM5
CUR NUM
TRIGGER
*1
EXP2
EXP3
INTERNAL
CTL1–CTL3
PEDAL
CTL4, CTL5
CTL6, CTL7
BANKDOWN
BANKUP
CC#1–31, 64–95
TIME *1 0–100
LINEAR
CURVE *1 SLOW RISE
FAST RISE
SAW
FORM *2 TRI
SINE
0–100,
WAVE
BPM ΠР`
PEDAL
* When set to BPM, the value of each parameter will
be set according to the value of the "MASTER BPM"
specified for each patch. This makes it easier to
RATE *2
achieve effect sound settings that match the tempo
of the song.
* If, due to the tempo, the time is longer than the
range of allowable settings, it is then synchronized
to a period either 1/2 or 1/4 of that time.
30
Explanation
This is activated when a patch is
selected.
This is activated when the GT-1000's
expression pedal is set to the
minimum position.
This is activated when the GT-1000's
expression pedal is moved through
the middle position.
This is activated when the GT-1000's
expression pedal is set to the
maximum position.
This is activated when the [EXP 1]
switch is operated.
This is activated when the [1]–[5]
switch is operated.
This is activated when you operate
the same number switch as the
selected patch number.
This is activated when an external
expression pedal connected to the
CTL 4, 5/ EXP 2 jack.
This is activated when an external
expression pedal connected to the
CTL 6, 7/ EXP 3 jack.
This is activated when the [CTL 1]–
[CTL 3] switch is operated.
This is activated when an external
footswitch connected to the CTL 4,
5/ EXP 2 jack is operated.
This is activated when an external
footswitch connected to the CTL 6,
7/ EXP 3 jack is operated.
This is activated when the [BANK I ]
switch is operated.
This is activated when the [BANK H ]
switch is operated.
This is activated when a control
change is received.
This specifies the time over which
the internal pedal will move from the
toe-raised position to the toe-down
position.
This determines the time spend for
one cycle of the assumed EXP Pedal.
Parameter Value
SYSTEM
MIDI CH *3 *4
1–16
CC# 0–127
TARGET
MIN 0–127
MIDI CC# *3
MAX 0–127
PC#
1–128
TARGET MSB OFF, 0–127
MIDI PC# *4
LSB OFF, 0–127
*1 The INTERNAL PEDAL TRIGGER, INTERNAL PEDAL TIME, and INTERNAL PEDAL
CURVE parameters are enabled when the SOURCE parameter is set to INT PEDAL.
*2 The WAVE PEDAL FORM and WAVE PEDAL RATE parameters are enabled when the
Source parameter is set to WAVE PEDAL.
*3 The MIDI CH, TARGET MIDI CC# parameters are enabled when the TARGET is set to
MIDI CC.
*4 The MIDI CH, TARGET MIDI PC# parameters are enabled when the TARGET is set to
MIDI PC.
Explanation
This transmits a message on the
MIDI channel specified by the "MIDI
SETTING" (p. 41) parameter TX
CHANNEL.
The message is transmitted on the
specified MIDI channel.
The message is transmitted using
the specified controller number.
Selects the minimum value of the
transmitted CC# message.
Selects the maximum value of the
transmitted CC# message.
Specifies the program number that
is transmitted.
Specifies the bank select MSB that is
transmitted. If this is OFF, the bank
select MSB is not transmitted.
Specifies the bank select MSB that is
transmitted. If this is OFF, the bank
select LSB is not transmitted.