Table of Contents
Advertisement
Quick Links
NFX150-S1 Network Services Platform
Quick Start
NFX150 Network Services Platform Overview
The Juniper Networks NFX150 Network Services Platform is a secure, automated, software-driven customer premises equipment
(CPE) that delivers virtualized network and security services on demand. The NFX150 integrates routing, switching, and security
functions on a single platform. The NFX150 is suited for small to medium-sized enterprises and can be used as a secure router
or Universal CPE (uCPE).
For more information on NFX150 Hardware, see the NFX150 Hardware Guide available at:
https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/
Package Contents
The NFX150-S1 device is shipped with the following parts:
One pair of front-mounting brackets
Eight screws to secure the mounting brackets to the chassis
An AC power cord with plugs appropriate for your geographical location
RJ-45 cable and RJ-45 to DB-9 serial port adapter
Register the Product
Register product serial numbers on the Juniper Networks website and update the installation base data if there is any addition
or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable for not
meeting the hardware replacement service-level agreement for products that do not have registered serial numbers or accurate
installation base data.
Register your product at
https://tools.juniper.net/svcreg/SRegSerialNum.jsp
Update your installation base at
https://www.juniper.net/customers/csc/management/updateinstallbase.jsp
.
.
Advertisement
Table of Contents
Related Manuals for Juniper NFX150-S1
Summary of Contents for Juniper NFX150-S1
- Page 1 Register product serial numbers on the Juniper Networks website and update the installation base data if there is any addition or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable for not meeting the hardware replacement service-level agreement for products that do not have registered serial numbers or accurate installation base data.
-
Page 2: Nfx150-S1 Front Panel And Rear Panel
Mount an NFX150-S1 Device on Two Posts of a Rack To mount an NFX150-S1 device on a rack, you require the parts that are shipped with the device along with the following additional parts and equipment. These are not shipped with the device. - Page 3 For information about installing the grounding cable, see the NFX150 Hardware Guide available at: https://www.juniper.net/documentation/en_US/release-independent/junos/information-products/pathway-pages/nfx-series/product/ You can mount an NFX150-S1 device on two posts of a 19-in. rack by using the mounting brackets provided with the device. To install NFX150-S1 on two posts of a 23-in. rack, you need additional mounting brackets.
-
Page 4: Connect Power To The Device
NFX150-S1 Network Services Platform Quick Start Connect Power to the Device CAUTION: Wrap and fasten one end of the ESD grounding strap around your wrist and connect the other end to a site ESD point. NOTE: Ensure that you ground AC-powered systems by attaching one end of the grounding cable to earth ground and the other end to the chassis grounding points. -
Page 5: Access The Device
NFX150-S1 Network Services Platform Quick Start Table 2: Interface Mapping (continued) Port Label Interface Virtual Interface Security Zone DHCP State IP Address MGMT fxp0 192.168.1.1/24 Table 3: LTE Interfaces Interface Security Zone IP Address cl-1/1/0 dl0 (logical) untrust ISP assigned The NFX150 device is shipped with the following services enabled by default: DHCP, HTTPS, and TFTP. -
Page 6: Establish The Connection
ISP. The device is assigned an IP address by the ISP through heth-0-4 heth-0-5 DHCP. Figure 4: Connecting the Interfaces on an NFX150-S1 Device Internet Optionally, you can obtain a SIM card from the ISP and connect the device through LTE. NOTE: The LTE expansion module must be purchased separately. -
Page 7: Next Steps
NFX150-S1 Network Services Platform Quick Start Connect the laptop to one of the front panel LAN ports such as , or . The laptop is assigned heth-0-0 heth-0-1 heth-0-2 heth-0-3 an IP address by the DHCP server running on the interface. - Page 8 NFX150-S1 Network Services Platform Quick Start Juniper Networks, the Juniper Networks logo, Juniper, and Junos are registered trademarks of Juniper Networks, Inc. and/or its affiliates in the United States and other countries. All other trademarks may be property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document.