York OPTIVIEW Operation Manual page 153

FORM 160.78-O2
ISSUE DATE: 5/22/2017
Variable Speed Drive
-----------------------------------------------------
Local Input Current Limit
Remote ISN Input Current Limit
Remote Analog Input Current Limit
Remote Digital Input Current Limit
Remote Modem Input Current Limit
Pulldown Demand Limit
Pulldown Demand Time
Input Job Full Load Amps
Rated Motor Voltage
Maximum Motor Current
Output Current Rating
Stator Resistance
Stator Inductance
Rotor Resistance
Rotor Inductance
Magnetizing Inductance
Poles
Motor Back-EMF Constant
Motor Power Factor
DC Bus Voltage Setpoint
Operation Mode
Soft Shutdown Frequency
Flux Command
Current Kp
Current Ki
Current Anti-Windup
Flux Kp
Flux Ki
Flux Anti-Windup
Speed Kp
Speed Ki
Speed Anti-Windup
SW Fault Mask 1
SW Fault Mask 2
SW Fault Mask 3
Motor Monitoring
-----------------------------------------------------
Motor Temperature 1
Motor Temperature 2
Motor Temperature 3
Motor Temperature 4
Motor Temperature 5
Motor Temperature 6
Capacity Control
-----------------------------------------------------
VSD Start Frequency
VSD Soft Shutdown Ramp Rate
PRV Start Position
PRV Shutdown Position
HGBP Start Position
LCHLT Setpoint Ramp Rate
LCHLT Setpoint Start Offset
Temperature Control Kp
Temperature Control Ti
Temperature Control Td
Temperature Control Max Loading Delta
Temperature Control Max Unloading Delta
VSD Output Gain
FIGURE 58 - SAMPLE PRINTOUT (SETPOINTS)
(CONT'D)
JOHNSON CONTROLS
VGD Output Gain
PRV Output Gain
= 100 %
= 30 %
= 100 % HGBP Output Gain
= 100 % Minimum PRV Position
= 100 %
= 100 % Min Frequency Multiplier
= 0 Min Min Frequency Offset
= 185 A Min Freq Rate – HGBP Closed (C.OPT.16.01.213 only)
= 507V Min Freq Rate – HGBP Open (C.OPT.16.01.213 only)
Min Freq Rate Maximum – 10.00 Hx/Sec (C.OPT.16.02.213
= 505 A
= 525 A and later)
Min Freq Rate Minimum – 0.10 Hx/Sec (C.OPT.16.02.213
= 90
= 6 and later)
Min Frequency Admin Multiplier
= 90
= 0 Min Frequency Mid Position
Min Frequency Coefficient a1
= 0
= 2 Min Frequency Coefficient a2
Min Frequency Coefficient a3
= 3276
= 0 Min Frequency Coefficient b1
Min Frequency Coefficient b2
= 750 V
= Voltage Min Frequency Coefficient b3
Transient Time Delay
= 50.00 Hz
= 0 Transient Deadb Band
= 0 Transient Max Change
= 0 Max VGD Knee PRV
= 0
= 0 Max VGD Knee VGD
= 0
= 0 Max VGD Coefficient A
= 0
= 0 Max VGD Coefficient B
= 0
Evaporator Pressure Load Limit Threshold
= 0
= 0 Evaporator Pressure Load Limit Delta
Evaporator Pressure Max Override Threshold
= 0
Evaporator Pressure Max Override Delta
Condenser Pressure Load Limit Threshold
Condenser Pressure Load Limit Delta
Condenser Pressure Max Override Threshold
= Enabled
= Enabled Condenser Pressure Max Override Delta
Input Current Load Limit Threshold
= Enabled
= Enabled Input Current Load Limit Delta
Input Current Max Override Threshold
= Enabled
= Enabled Input Current Max Override Delta
Motor Current Load Limit Threshold
Motor Current Load Limit Delta
Motor Current Override Threshold
= 172.70 Hz Motor Current Max Override Threshold
= 20 Hz/Sec Motor Current Max Override Delta
= 30.0 % LCHLT Max Override Delta
= 10.0 %
= 0.0 %
= 0.1 ~F/S
FIGURE 58 - SAMPLE PRINTOUT (SETPOINTS)
= 10.0 ~F
(CONT'D)
= 5.0
= 25.0
= 0.0
= 1.0
= 1.0
= 0.5
SECTION 4 - PRINTERS
= 1.0 (Gas
Path B)
= 1.0 (Gas
Path A)
= 1.0
= 5.0% (Gas
Path A)
= 40.0 %
= 1.440
= 1.315
= 1.305
= 0.525
= 0.497
= 0.495
= 2.5
= 0.010
= 0.25 4
= 5.0% (Gas
Path A)
= 5.0% (Gas
Path A)
= 5.0 (Gas
Path A)
= 5.0 (Gas
Path A)
153