Listening To A Program Source - Sherwood RVD-6090R Operation Instructions Manual

O O p p e e r r a a t t i i o o n n s s

LISTENING TO A PROGRAM SOURCE

B B e e f f o o r r e e o o p p e e r r a a t t i i o o n n
Enter the standby mode.
The STANDBY indicator lights up. This means
that the receiver is not disconnected from the AC
mains and a small amount of current is retained to
support the memorized contents and operation
readiness.
To switch the power off, push the POWER switch
again.
Then the power is cut off and the STANDBY
indicator goes off.
In the standby mode, turn the power on.
1
INPUT SELECTOR
or
VIDEO
AUDIO
Each time the POWER button on the remote
control is pressed, the receiver is turned on to enter
the operating mode or off to enter the standby
mode.
In the standby mode, if the INPUT SELECTOR
button is pressed, the receiver is turned on
automatically and the desired input is selected.
Switch the speakers on.
2
Then sound can be heard from the speakers
connected to the speaker terminals.
When using headphones for private listening, press
the SPEAKER switch again to switch the speakers
off.
POWER
ON/OFF
POWER
POWER P .SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD
or
REPEAT INTRO
A B < <
A
DECK SEL.
B DECK
PRESET USER FILE T .MON DISPLAY
CD TUNER VCR 1 EQUALIZER
AUX TAPE MON. VCR 2 STEREO
CD TUNER VCR 1
6CH DIRECT DVD/TV DSP MODE
INPUT
SELECTOR
T .TONE CH SEL.
D.TIME ADJUST
CH LEVEL MASTER
AUX TAPE MON. VCR 2
DISPLAY SLEEP MUTE
SYS
6CH DIRECT DVD/TV
INPUT
SELECTOR
SPEAKER
ON/ OFF
Select the desired input source.
3
INPUT SELECTOR
VIDEO
AUDIO
TAPE MONITOR
Each time the "AUDIO" button is pressed, the input
source changes as follows;
→ TUNER → CD → AUX
(frequency display)
Each time the "VIDEO" button is pressed, the input
source changes as follows;
→ VCR1 → VCR2 → DVD
When the TAPE MONITOR button is set to on so that
"TAPE M" indicator lights up, other inputs can not be
heard from the speakers.
To listen to a input source other than TAPE
MONITOR, be sure to set the TAPE MONITOR
button to off.
TAPE MONITOR function
You can connect either a tape deck or a graphic equalizer to
the receiver's TAPE MONITOR jacks.
To listen to the component connected to these jacks, set the
TAPE MONITOR button to on.
If you connect a 3-head tape deck, you can listen to the sound
being recorded during recording, not the source sound.
For further details, refer to the operating instructions of the
component connected.
When selecting the 6 CH DIRECT as desired,
"6-DIRECT" is
displayed and the 6
separate analog
signals from 6 CH
decoder connected to
this unit pass through
the tone (bass, treble)
and volume circuits only and directly transfer to the
speakers. (In case that the TAPE MONITOR button
is set to on, the TAPE MONITOR button is
automatically set to off.)
To cancel the 6 CH Direct function, press the 6 CH
DIRECT button or select the desired input source.
These 6 separate analog signals can be heard only,
not recorded.
10
POWER P .SCAN
1 2 3 4 5
6 7 8 9 0
DISC
CD TUNER VCR 1 CD
REPEAT INTRO
< <
A B
or
A
DECK SEL.
B DECK
PRESET USER FILE T .MON DISPLAY
AUX TAPE MON. VCR 2
CD TUNER VCR 1 EQUALIZER
AUX TAPE MON. VCR 2 STEREO
6CH DIRECT DVD/TV DSP MODE
INPUT
SELECTOR
DVD/TV T .TONE CH SEL.
D.TIME ADJUST
CH LEVEL MASTER
DISPLAY SLEEP MUTE
SYS
POWER P .SCAN
1 2 3 4
6 7 8 9
DISC
6 CH
REPEAT
< <
A B
DIRECT
A
DECK SEL.
B DECK
PRESET USER FILE T .MON DISPLAY
CD TUNER VCR 1 EQUALIZER
AUX TAPE MON. VCR 2 STEREO
6CH DIRECT DVD/TV DSP MODE
INPUT
SELECTOR
T .TONE CH SEL.
or
6CH DIRECT
D.TIME ADJUST
CH LEVEL MASTER
DISPLAY SLEEP MUTE
SYS
5
0
CD
INTRO