Grizzly G0513 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Saw
  5. G0513 SERIES
  6. Owner's manual

Grizzly G0513 Owner's Manual

G0513 series, heavy-duty 17 inch bandsaw
Hide thumbs Also See for G0513:
Table of Contents

Advertisement

Quick Links

See also: Instruction Manual
MODEL G0513 SERIES
HEAVY-DUTY 17" BANDSAW
OWNER'S MANUAL
(MODELS G0513, G0513ANV
& EXTREME MODELS G0513X2, G0513X2B,
G0513X2BF & G0513X2F)
Model
Model
G0513X2B
G0513X2F
For Models
G0513,
G0513X2,
G0513X2BF,
For Model
G0513X2F
G0513X2B
Only
Only
COPYRIGHT © NOVEMBER, 2012 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2018 (MN)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MACHINES MFD. SINCE 07/18) #TS15097 PRINTED IN TAIWAN
V3.11.18

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0513

Summary of Contents for Grizzly G0513

  • Page 1 G0513X2B Only Only COPYRIGHT © NOVEMBER, 2012 BY GRIZZLY INDUSTRIAL, INC. REVISED NOVEMBER, 2018 (MN) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. (FOR MACHINES MFD. SINCE 07/18) #TS15097 PRINTED IN TAIWAN...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Motor Brake ..........4 Adjusting Blade Support Bearings ....35 Rear Controls ..........5 Adjusting Blade Guides ....... 36 G0513 Series Combination Data Sheet ..6 Adjusting Blade Guides (G0513 & G0513ANV) ..........37 SECTION 1: SAFETY ........8 Adjusting...
  • Page 4 SECTION 9: PARTS ........77 Wheel Brush ..........58 G0513 & G0513ANV Main......77 Cleaning & Protecting ........58 G0513 & G0513ANV Table, Trunnion & Lubrication ........... 58 Lower Blade Guides ........79 Blade Post Rack ........58 G0513 & G0513ANV Fence ......80 Tension Adjustment Assembly ....

  • Page 5: Introduction

    Combination Manual The G0513 Series Bandsaws share many similari- ties. Thus, this combination manual includes infor- mation for all seven models of the G0513 Series Manufacture Date Bandsaws. Unless otherwise specified, information applies to Serial Number all models.

  • Page 6: Basic Controls

    Control Panel opening the wheel cover. The 2-button power switch on Models G0513, G0513ANV, and G0513X2 is located on the col- D. Fence and Miter Gauge: Supports workpiece umn for easy access (see Figure 1). The power for controlled straight or angled cuts.

  • Page 7: Rear Controls

    Guide Post Handwheel and Lock Knob: Quickly moves the upper guide post to the desired height; locks setting. Figure 4. Rear controls (G0513X2B shown). To reduce your risk of serious injury, read this entire manual BEFORE using machine. G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 8: G0513 Series Combination Data Sheet

    9.5A at 220V Speed 1720 RPM Cycle 60 Hz Power Transfer Belt Drive Bearings Shielded and Permanently Lubricated Operation Blade Speeds 1700, 3500 FPM Left 10°, Right Table Tilt Left 5°, Right 45° 45° G0513 Series Bandsaws (Mfd. Since 07/18)
  • Page 9 2 at 4" Mobile Base Model D2057A Other Specifications Country of Origin Taiwan Warranty 1 Year ISO Factory Serial Number Location ID Label on Upper Wheel Cover Assembly Time 1 Hour CSA Certified G0513 Only G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 10: Section 1: Safety

    Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. G0513 Series Bandsaws (Mfd. Since 07/18)
  • Page 11 Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 12: Additional Safety For Bandsaws

    DO NOT try to stop or slow blade with your This machine is NOT designed to cut metal, hand or the workpiece. glass, stone, tile, etc. -10- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 13: Section 2: Power Supply

    G0513 & G0513ANV Full-Load Current Rating At 110V ..........20 Amps At 220V ..........10 Amps G0513X2 & G0513X2F Full-Load Current Rating At 110V ..........19 Amps...

  • Page 14: Circuit Requirements

    These machines are prewired to operate on a 220V power supply circuit that has a verified ground and meet the 220V operation requirements listed below. Models G0513, G0513ANV, G0513X2, and G0513X2F can be converted to operate on a 110V power supply (refer to Voltage Conversion instructions beginning on Page 14) that has a verified ground and meets the 220V operation requirements listed below.
  • Page 15 L5-30 GROUNDED codes in your area. LOCKING RECEPTACLE Neutral L5-30 LOCKING PLUG Grounding Prong is Hooked Figure 6. Typical L5-30 plug and receptacle. -13- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 16: Extension Cords

    Maximum Length (Shorter is Better)..50 ft. If the diagram included on the motor con- flicts with the one in this manual, the motor may have changed since the manual was printed. Use the diagram provided on the motor. -14- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 17: Section 3: Setup

    IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.

  • Page 18: Hardware Recognition Chart

    Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -16- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 19: Inventory

    Rail Pad M6-1 x 18 (Fence) ......1 • Hex Wrench 5mm, 8mm....1 Each • Open-End Wrench 10 x 13mm ....1 SUFFOCATION HAZARD! Keep children and pets away from plastic bags or packing materials shipped with this machine. -17- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 20: G0513X2

    Fence Handle M8-1.25 x 22 (Fence) ..1 • Moving Plate (Fence)........1 • Hex Wrench 5mm, 8mm....1 Each • Open-End Wrench 10 x 13mm ....1 Figure 10. Other bandsaw components. -18- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 21: G0513X2F

    Fence Handle M8-1.25 x 22 (Fence) ..1 • Moving Plate (Fence)........1 • Hex Wrench 5mm, 8mm....1 Each • Open-End Wrench 10 x 13mm ....1 Figure 12. Other bandsaw components. -19- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 22: G0513X2B & G0513X2Bf

    • Knobs M8-1.25 x 20 ........2 • Rail Plates ..........3 • Hex Wrench 5mm, 8mm....1 Each • Open End Wrench 10 x 13mm ....1 Figure 14. Other bandsaw components. -20- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 23: Cleanup

    Figure 15. T23692 Orange Power Degreaser. Repeat Steps 2–3 as necessary until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust. -21- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 24: Site Considerations

    Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use. Figure 17. Lifting the bandsaw. Remove the pallet and slowly set the bandsaw into position. -22- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 25: Using Wood Blocks

    Anchor studs are stronger and more per- manent alternatives to lag shield anchors; however, they will stick out of the floor, which may cause a tripping hazard if you decide to move your machine. -23- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 26: Assembly

    Remove the saw blade (refer to Blade Changes on Page 51 for detailed instruc- tions). With the help of another person, lift the table Positive Stop onto the trunnions. Figure 22. Positive stop bolt installed. -24- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 27: Installing Fence (G0513, G0513Anv, G0513X2 & G0513X2F)

    Attach the front rail with the (2) M6-1 x 20 hex Models G0513 and G0513ANV: Secure the bolts, 6mm lock washers, and 6mm flat wash- table to the trunnions, as shown in Figure 24 ers, as shown in Figure 25.

  • Page 28: (G0513X2B G0513X2Bf)

    Cap Screw Knob M6-1 x 20 Cap Screw Lock Washer Figure 27. Fence assembly installed on G0513 M8-1.25 x 20 and G0513ANV. Figure 29. Installing front rail onto table. Attach the outer two rail plates with the round and elongated mounting holes to the outer Fence part of the table bottom with (2) M8-1.25 x 20...

  • Page 29: Installing Resaw Fence (G0513X2, G0513X2B, G0513X2Bf & G0513X2F)

    Figure 33. Attaching resaw fence. Pointer Nut Pointer Locking Handle Resaw Fence Figure 32. Calibrating fence pointer Figure 34. Resaw fence properly installed. (adjustment nut out of view). Re-tighten the pointer adjustment nut. -27- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 30: Initial Blade Tracking

    (see Figure 35) is between 4 and 6. CENTER TRACKING IMPORTANT Blade Tension Changes made to the blade tension may Scale change how the blade tracks. Blade Tension Handwheel Figure 35. Blade tensioning controls. -28- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 31: Adjusting Positive Stop

    Loosen the screw on the pointer, but do not remove it. Align the tip of the pointer with the 0˚ mark on the table tilt scale, then re-tighten the screw to secure the setting. -29- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 32: Dust Collection

    Explaining how to cal- culate these variables is beyond the scope of Figure 39. Dust hose attached to bottom dust this manual. Consult an expert or purchase a port. good dust collection "how-to" book. -30- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 33: Power Cord Connection

    Remove the power supply junction box cover from the right rear of the bandsaw (see Figure 40). It is secured by two screws. Power Supply Junction Box Strain Relief Figure 40. Power supply junction box on rear of bandsaw. -31- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 34: Test Run

    Always ing with regular operations. Call Tech disconnect the machine from power Support for help. when investigating or correcting potential problems. -32- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 35: Tensioning Blade

    Initial Blade Tracking adjustments before putting the bandsaw into full on Page 28. operation. Raise the guide post all the way, and move the upper and lower blade guides away from the blade. -33- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 36: Deflection Method

    10. Re-adjust blade guides as described in Adjusting Blade Guides beginning on Page 36 for your model bandsaw. -34- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 37: Adjusting Blade Support Bearings

    Figure 47. Upper support bearing controls. Before adjusting the blade support bear- ings, make sure the blade is tracking prop- erly (Page 28) and that it is correctly ten- sioned (Page 33). Figure 48. Lower support bearing controls. -35- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 38: Adjusting Blade Guides

    IMPORTANT: Although the function and the dis- tance adjustment of the blade guides is the same for all the G0513 Series Models, the guide con- trols are not all the same. Use the set of instruc- tions on the following pages that is correct for your model of bandsaw.

  • Page 39: Adjusting Blade Guides (G0513 & G0513Anv)

    Figure 51. Blade Guide 0.016" Thumb Screws Figure 49. Upper blade guides side-to-side con- trols. Tooth Support Guide Gullet Bearing Guide Block 0.016" Block Cap Screw Figure 51. Back of upper blade guides. Blade -37- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 40: Adjusting Blade Guide Bearings (G0513X2, G0513X2B, G0513X2Bf, & G0513X2F)

    Guide Guide Block Block Cap Screw Figure 53. Lower blade guide controls. -38- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 41: Aligning Table

    (see Figure 56). Re-tighten the cap screws to lock the blade guide bearings in position. Figure 56. Measuring for miter slot to be parallel with blade. -39- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 42: Aligning Fence

    Re-tighten the trunnion bolts to secure the settings. Figure 58. G0513 & G0513ANV fence caps screws. Blade Square G0513X2F Fence...

  • Page 43: Aligning Fence (G0513X2B & G0513X2Bf)

    0˚ mark slot. on the scale. Tighten the knobs and cap screw that secure Re-tighten the screw to secure the setting. the rail to the table, being careful not to move the fence. -41- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 44: Section 4: Operations

    Read books/magazines or get formal training before beginning any proj- ects. Regardless of the content in this sec- tion, Grizzly Industrial will not be held liable for accidents caused by lack of training. -42- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 45: Disabling & Locking Switch (G0513, G0513Anv, G0513X2)

    To help prevent unsupervised operation, properly disabled. remove the key from the switch before leaving machine unattended! Place key in a well-hidden or secure location. -43- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 46: General Overview

    On the contrary, a workpiece supported on the bowed side will rock during a cut, leading to loss of control. -44- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 47: Models G0513 & G0513Anv

    G0513X2BF & G0513X2F Model Tilt Specifications Angle Indicator Scale G0513, G0513ANV ....10° left, 45° right G0513X2 ........5° left, 45° right G0513X2B ........5° left, 45° right G0513X2BF ........ 5° left, 45° right G0513X2F ........5° left, 45° right...

  • Page 48: Guide Post

    Figure 66. Guide post controls. Turn the guide post handwheel to adjust the upper blade guide assembly to within 1" from the top of the workpiece. Lock the guide post in place with the lock knob. -46- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 49: Blade Selection

    Figure 69. Carbide-tooth blade composition. H. Blade Back: The distance between the bot- tom of the gullet and the back edge of the blade. TPI: The number of teeth per inch measured from gullet to gullet. -47- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 50: Tooth Set

    Skip (or Skip Tooth) tooth set removes material in a different manner, leaving cuts with different characteristics (see Figure 71). Figure 72. Typical tooth types. Alternate Raker Figure 71. Common woodcutting bandsaw blade tooth sets. -48- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 51: Blade Selection Chart

    Crosscutting Thick Stock Crosscutting Round Stock Mitre Cut Tenons Sharp Curves Gradual Curves Tooth Type Tooth Pitch (Teeth per Inch or TPI) Fine Medium Coarse Hook Raker Skip (14-32 TPI) (4-12 TPI) (2-4 TPI) -49- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 52: Blade Breakage

    • Using the wrong pitch (TPI) for the workpiece thickness. The general rule of thumb is to have not less than two teeth in contact with the workpiece at all times during cutting. -50- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 53: Blade Changes

    Open the upper and lower wheel covers, and with gloved hands, slide the blade off of both wheels. Rotate the blade 90˚ and slide it through the slot in the table to remove it. -51- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 54: Blade Speed

    DISCONNECT BANDSAW FROM POWER! Loosen the motor mount cap screws shown in Figure 75, and rotate the motor to loosen the V-belt. Motor Wheel Figure 77. V-belt deflection. Figure 75. Motor mount cap screws. -52- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 55: Crosscutting

    (blade lead) can tear through the sur- face of the workpiece, exposing your hands to the blade teeth. Always use push blocks when resawing and keep your hands clear of the blade. Figure 78. Example of crosscutting. -53- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 56: Cutting Curves

    Turn the bandsaw ON. Using push paddles and a push stick, keep pressure against the fence and table, and slowly feed the workpiece into the moving blade until the blade is completely through the workpiece. -54- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 57: Stacked Cuts

    On the face of the top piece, lay out the Figure 81. Example of stack cutting. shape you intend to cut. -55- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 58: Section 5: Accessories

    0.025 H8597 ⁄ " Raker 0.025 H8598 ⁄ " Thin 0.025 H8599 1" Pos. Claw 0.035 Figure 83. T26544 LED Light with Base and Flexible Arm. www.grizzly.com 1-800-523-4777 order online at or call -56- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 59: Basic Eye Protection

    Gun Treatment 4.5 Oz. Spray ® D2272 D2274 D2273 Figure 85. Recommended products for protect- Figure 87. SHOP FOX ® Roller Stands. ing unpainted cast iron/steel part on machinery. www.grizzly.com 1-800-523-4777 order online at or call -57- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 60: Section 6: Maintenance

    Frequency .......... As Needed Adjusting Wheel Brush on Page 65 for detailed instructions). To lubricate the blade post rack and pinion: DISCONNECT BANDSAW FROM POWER! Lower blade guides until they reach the table. -58- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 61: Tension Adjustment Assembly

    Trunnions Move the blade post up and down several times to distribute the lubricant, then remove Models G0513 and G0513ANV have steel trun- any excess grease to help reduce potential nions that can be cleaned and lubricated with GL2 sawdust build-up.

  • Page 62: Section 7: Service

    11. Tighten or re-align pulleys; replace bent shaft. 12. Worn wheel bearing. 12. Check/replace wheel bearing. 13. Wheel tires worn. 13. Replace tires. 14. Wheels out of balance. 14. Replace wheels. 15. Motor at fault. 15. Repair/replace motor. -60- G0513 Series Bandsaws (Mfd. Since 07/18)
  • Page 63 9. Blade weld at fault. 10. Wheel tires worn or damaged. 10. Replace tires. 11. Align miter slot and fence with blade (Page 39). 11. Fence or miter slot not aligned with blade. -61- G0513 Series Bandsaws (Mfd. Since 07/18)
  • Page 64 7. Tighten table mounting bolts or tilt lock lever. 8. Fence/miter slot out of alignment. 8. Align table miter slot and fence with blade (Page 39). 9. Blade guides mis-adjusted. 9. Adjust blade guides (Page 36). -62- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 65: V-Belt Service

    Re-install the lower wheel back and secure it must properly re-tension the V-belt. with the wheel mount bolt. Tools Needed: Re-install the blade and close the wheel cov- Hex Wrench 6mm ..........1 ers. Hex Wrench 8mm ..........1 -63- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 66: Blade Lead

    3" wide x 17" long. On a wide face of Lead adjustments will change when new the board, draw a straight line parallel to the blades are mounted on the saw. long edge. -64- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 67: Adjusting Wheel Brush

    Thread the tension adjustment screw (see Figure 96) down until it contacts the wheel block plate, then back it off 1-2 turns. Re-tighten the jam nut. -65- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 68: Adjusting Guide Post Travel

    Tighten the screws shown in Figure 98. to the right hand side of the guide post, as shown in Figure 97. (Front View) Guide Post Figure 97. Example of checking guide post squareness. -66- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 69: With Blade Front-To-Back

    —If the measurements are not equal, con- tinue adding shims as needed until guide post rack to blade distance is the same at the top and bottom. Re-install the guide post guard with the screws removed in Step 3. -67- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 70: Aligning Wheels

    Place your coplanarity gauge up against both Figure 102. Checking for coplanarity. wheels in the positions shown in Figure 102. -68- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 71: Shimming Upper Wheel

    Remove the blade from the saw, then remove operations.) the wheel that needs to be shimmed. Determine how many shim washers you need to compensate for the distance measured in Step 3 and place them on the wheel shaft. -69- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 72: Adjusting Lower Wheel

    Tighten the jam nuts to lock the tilt adjust- brake on either side. ment set screws in position. Tighten the cap screws on the brake shoe and motor fan, remove the feeler gauge, then reinstall the motor fan cover. -70- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 73: Section 8: Wiring

    Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -71- G0513 Series Bandsaws (Mfd. Since 07/18)

  • Page 74: G0513, G0513Anv & G0513X2 Wiring Diagram

    G0513, G0513ANV & G0513X2 Wiring Diagram Ground Neutral Power Switch (viewed from behind) 110 VAC L5-30 Plug (As Recommended) Ground 220 VAC Ground 6-15 Plug (As Recommended) Ground Motor @220V Rewired to 110V Ground Motor @110V READ ELECTRICAL SAFETY -72- G0513 Series Bandsaws (Mfd.

  • Page 75: G0513X2B Wiring Diagram

    CONTROL PANEL (viewed from behind) L1/1 L2/3 L3/5 NO13 MA-18 NC15 NC16 NO14 T1/2 T2/4 T3/6 RA-20 8-12 MAGNETIC SWITCH Ground 220V MOTOR Magnetic Brake Capacitor 45MFD 450VAC READ ELECTRICAL SAFETY -73- G0513 Series Bandsaws (Mfd. Since 07/18) ON PAGE 71!

  • Page 76: G0513X2Bf Wiring Diagram

    L3/5 NO13 Contactor SDE MA-18 NC15 NC16 T1/2 T2/4 T3/6 NO14 OL Relay SDE RA-20 Set at 8.7A Motor Ground Magnetic Brake YZG Run Capacitor 45MFD 450VAC READ ELECTRICAL SAFETY -74- G0513 Series Bandsaws (Mfd. Since 07/18) ON PAGE 71!

  • Page 77: G0513X2F 220V Wiring Diagram

    NO13 Conctactor SDE MA-09 NC15 NC16 T1/2 T2/4 T3/6 NO14 OL Relay SDE RA-20 Set at Start Capacitor 300MFD 250VAC Ground 220V Motor Run Capacitor 40MFD 250VAC READ ELECTRICAL SAFETY -75- G0513 Series Bandsaws (Mfd. Since 07/18) ON PAGE 71!

  • Page 78: G0513X2F 110V Wiring Diagram

    NO13 Conctactor SDE MA-18 NC15 NC16 T1/2 T2/4 T3/6 NO14 OL Relay SDE RA-30 Set at Start Capacitor 300MFD 250VAC Ground 110V Motor Run Capacitor 40MFD 250VAC READ ELECTRICAL SAFETY -76- G0513 Series Bandsaws (Mfd. Since 07/18) ON PAGE 71!

  • Page 79: Section 9: Parts

    Call (800) 523-4777 82-8 or visit www.grizzly.com/parts to check for availability. 82-7 82-9A 82-10 82-11 95V2 (G0513ANV) BUY PARTS ONLINE AT GRIZZLY.COM! -77- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 80 G0513 & G0513ANV Main Parts List PART # DESCRIPTION PART # DESCRIPTION P0513004 LIFTING EYE BOLT M10-1.5 P0513059 HEX BOLT M6-1 X 25 P0513005 MACHINE BODY (G0513) P0513060 STAR KNOB P0513ANV005V2 MACHINE BODY V2.04.17 (G0513ANV) P0513061 LOCK NUT M6-1 P0513008...

  • Page 81: G0513 & G0513Anv Table, Trunnion & Lower Blade Guides

    G0513 & G0513ANV Table, Trunnion & Lower Blade Guides REF PART # DESCRIPTION PART # DESCRIPTION P0513077 LOCK WASHER 8MM P0513118 LOCK HANDLE M8-1.25 P0513096 FLAT WASHER 8MM P0513119 FLAT WASHER 8MM P0513098 CAP SCREW M10-1.5 X 35 P0513120 POINTER P0513099 HEX NUT M10-1.5...

  • Page 82: G0513 & G0513Anv Fence

    CONVEX WINDOW P0513226 FLANGE SCREW M4-.7 X 10 P0513212 CAP SCREW M6-1 X 55 P0513227 FLAT WASHER 6MM P0513213 LOCK CAM BUY PARTS ONLINE AT GRIZZLY.COM! -80- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 83: G0513 & G0513Anv Upper Blade Guides & Miter Gauge

    G0513 & G0513ANV Upper Blade Guides & Miter Gauge 164V2 174V2 157A 161V2 138-1 173-5 173-4 173-2 173-6 173-9 173-3 173-1 173-8 173-7 BUY PARTS ONLINE AT GRIZZLY.COM! -81- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 84 G0513 & G0513ANV Upper Blade Guides & Miter Gauge Parts List PART # DESCRIPTION PART # DESCRIPTION P0513006 SET SCREW M5-.8 X 5 161V2 P0513161V2 THREADED BUSHING V2.06.09 P0513134 GUIDE ADJUSTMENT SHAFT P0513162 CAP SCREW M8-1.25 X 20 P0513136 CAP SCREW M8-1.25 X 80...

  • Page 85: G0513 Labels

    FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK WARNING! WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. To reduce risk of death artwork changes are required, contact us immediately at manuals@grizzly.com. • 1:1 Sizing (Labels are...

  • Page 86: G0513Anv Labels

    191V2 P0513ANV191V2 GRIZZLY LOGO NAMEPLATE V2.04.17 P0513ANV183 UNPLUG BANDSAW LABEL P0513ANV192 ORANGE GRIZZLY.COM LABEL P0513ANV185 SAW TENSION LABEL 194V2 P0513ANV194V2 35TH ANNIVERSARY LABEL V2.04.17 BUY PARTS ONLINE AT GRIZZLY.COM! -84- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 87: G0513X2 Main

    17-5 18-4 18-5 18-2 18-3 18-3 18-1 18-2 82-1V2 82-8 82-5V2 82-9 82V2 82-2V2 82-6V2 82-3V2 82-10 82-7V2 82-4V2 82-11 BUY PARTS ONLINE AT GRIZZLY.COM! -85- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 88 CAP SCREW M6-1 X 10 P0513X2111 CAP SCREW M6-1 X 20 P0513X2050 CLEAR WINDOW P0513X2119 LOCK WASHER 4MM P0513X2055A UPPER WHEEL COVER ASSY BUY PARTS ONLINE AT GRIZZLY.COM! -86- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 89: G0513X2 Labels

    FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK respirator when WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. Generic Labels • Labels must be made of EYE/LUNG INJURY using this machine.

  • Page 90: G0513X2B Main

    19-5V2 19-9 19-8 19-8 19-1 19-3 19-7 19-6V2 82-4 82-5V2 82-12 82-11 82-10 82-6 82-2 82-13 82-14 82-15 82-9 82-3 BUY PARTS ONLINE AT GRIZZLY.COM! -88- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 91 HEX BOLT M10-1.5 X 25 P0513X2B039 FLANGE SCREW M5-.8 X 10 P0513X2B084 LOCK WASHER 10MM P0513X2B040 STOP BUTTON P0513X2B085 MOTOR MOUNT BRACKET BUY PARTS ONLINE AT GRIZZLY.COM! -89- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 92: G0513X2B Labels

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -90- G0513 Series Bandsaws (Mfd.

  • Page 93: G0513X2Bf Main

    17-1 17-4 17-2 17-5 18-4 18-5 18-2 18-3 18-3 18-1 18-2 82-4 82-5 82-14 82-9 82-6 82-15 82-2 82-10 82-3 BUY PARTS ONLINE AT GRIZZLY.COM! -91- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 94 CAP SCREW M8-1.25 X 16 P0513X2BF091 HEX BOLT M8-1.25 X 20 LH P0513X2BF045 FENDER WASHER 8MM P0513X2BF092 MOTOR PULLEY TYPE-A 3.5" BUY PARTS ONLINE AT GRIZZLY.COM! -92- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 95: G0513X2Bf Labels

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -93- G0513 Series Bandsaws (Mfd.

  • Page 96: G0513X2F Main

    17-2 17-5 18-4 18-5 18-2 18-3 18-3 18-1 18-2 82-8A 82-4 82-1 82-7 82-8 82-5 82-2 82-3 82-6 82-10 82-9 BUY PARTS ONLINE AT GRIZZLY.COM! -94- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 97 FLANGE SCREW M5-.8 X 10 P0513X2F057 FLAT WASHER 6MM P0513X2F189 CORD CLIP 5/16" P0513X2F058 WHEEL BRUSH P0513X2F190 TAP SCREW M4 X 10 BUY PARTS ONLINE AT GRIZZLY.COM! -95- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 98: G0513X2F Labels

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -96- G0513 Series Bandsaws (Mfd.

  • Page 99: G0513X2, G0513X2B, G0513X2Bf & G0513X2F Guides & Trunnions

    155-3 155-23 155-17 155-24 155-18 139V2 155-1 155-19 155-33 155-30 155-20V2 155-2 155-29 155-32 155-21 155-28 155-22 155-27 155-26 155-25 BUY PARTS ONLINE AT GRIZZLY.COM! -97- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 100 HEX WRENCH 8MM 151-5 P0513X2151-5 LOWER BLADE GUIDE SUPPORT P0513X2357 WRENCH 10 X 13 OPEN-END 151-6 P0513X2151-6 CAP SCREW M6-1 X 16 BUY PARTS ONLINE AT GRIZZLY.COM! -98- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 101: G0513X2 & G0513X2F Fence Assembly & Table

    GUARD PIECE 350-3 P0513X2350-2 FENCE END PLATE 148 X 22 X 1 121-18 P0513X2121-18 MOVING PLATE 350-4 P0513X2350-2 RESAW FENCE SCALE BUY PARTS ONLINE AT GRIZZLY.COM! -99- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 102: G0513X2B & G0513X2Bf Fence Assembly & Table

    LOCK WASHER 6MM 157-7 P0513X2B157-7 HEX NUT M8-1.25 165V2 P0513X2B165V2 CAP SCREW M6-1 X 20 157-8 P0513X2B157-8 FENCE LOCK HANDLE BUY PARTS ONLINE AT GRIZZLY.COM! -100- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.

  • Page 103: G0513X2Bf & G0513X2F Foot Brake

    STEP BOLT M7-1 X 10 W/BUSHING P0513X2F312 CAP SCREW M8-1.25 X 25 P0513X2F325 BRAKE LEVER P0513X2F313 CAP SCREW M6-1 X 25 P0513X2F326 RUBBER CLIP BUY PARTS ONLINE AT GRIZZLY.COM! -101- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 104 BUY PARTS ONLINE AT GRIZZLY.COM! -102- G0513 Series Bandsaws (Mfd. Since 07/18) Scan QR code to visit our Parts Store.
  • Page 105 Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times. _____ Yes _____No 10.
  • Page 106 FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...

  • Page 107: Warranty & Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

This manual is also suitable for:

G0513anvG0513x2bfG0513x2fG0513x2G0513x2b

Table of Contents