Grizzly G0513X2B Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Saw
  5. EXTREME G0513X2B
  6. Manual
Grizzly G0513X2B Manual

Grizzly G0513X2B Manual

Bandsaw w/motor brake manual insert
Hide thumbs Also See for G0513X2B:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual
model g0513X2b
17" bandsaW
w/motor braKe
manual insert
the Model g0513X2B is the same as the Model g0513X, except it has a cast iron trunnion, key switch, and
a magnetic brake motor. Besides the data sheet, circuit requirements, certain setup and operation proce-
dures, the wiring diagram, and parts in this insert, the content in the Model g0513X owner's manual is the
same for both machines. on the following pages, the header indicates which page it replaces in the Model
g0513X manual, if applicable.
Before operating your new machine, you Must read and understand this insert and the entire Model
g0513X manual to reduce the risk of injury from improper use or setup.
If you have any questions about this manual insert or the differences between the Model g0513X2B and the
Model g0513X, contact our Technical Support at (570) 546-9663 or email techsupport@grizzly.com.
252923
Copyright © MAy, 2008 By grizzly industriAl, inC. revised MArCh, 2012 (tr)
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
(For Models MAnuFACtured sinCe 5/11) #Bl10777 printed in tAiWAn

Advertisement

Table of Contents
loading

Related Manuals for Grizzly G0513X2B

Summary of Contents for Grizzly G0513X2B

  • Page 1 Model g0513X2B is the same as the Model g0513X, except it has a cast iron trunnion, key switch, and a magnetic brake motor. Besides the data sheet, circuit requirements, certain setup and operation proce- dures, the wiring diagram, and parts in this insert, the content in the Model g0513X owner's manual is the same for both machines.
  • Page 2 Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0513X2B 17" 2 HP EXTREME-SERIES® BANDSAW W/ CAST IRON TRUNNION & BRAKE. Product Dimensions: Weight... 352 lbs. Width (side-to-side) x Depth (front-to-back) x Height... 32 x 32 x 73 in.
  • Page 3 Ball Bearing Blade Guides Quick Change Blade Release/Tensioner Micro-Adjusting Gear Table Tilt Rack & Pinion Upper Blade Guide Height Adjustment Computer Balanced Cast Iron Wheels with Grizzly Bear Head Cut-Outs Blade Tension Indicator Height Scale for Upper Blade Guides Blade Tracking Window...
  • Page 4 Extended exposure to this noise without hearing protection can cause permanent hearing loss. MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted. Model g0513X2B (Mfg. since 5/11)
  • Page 5 FORCING MACHINERY.­Do­not­force­machine.­ It­ will­ do­ the­ job­ safer­ and­ better­ at­ the­ rate­ for­ which­it­was­designed. Model g0513X2B (Mfg. since 5/11) GUARDS & COVERS.­ Guards­ and­ covers­ can­ protect­ you­ from­ accidental­ contact­ with­ moving­ parts­ or­ flying­ debris.­ Make­ sure­ they­ are­ prop- erly­...
  • Page 6 Model g0513X2B (Mfg. since 5/11)
  • Page 7 Model g0513X2B (Mfg. since 5/11) circuit requirements for 220v This machine is prewired to operate on a 220V...
  • Page 8 Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following require- ments: minimum gauge size ...14 aWg maximum length (shorter is better)...50 ft. Model g0513X2B (Mfg. since 5/11)
  • Page 9 Fence ... 1 e. Front square rail ... 1 Fence Assembly ... 1 g. guide post handwheel... 1 figure 2. g0513X2B inventory. Model g0513X2B (Mfg. since 5/11) hardware and tools: • eye Bolt M10-1.5 (may be installed) ... 1 •...
  • Page 10 20 knobs and 8mm flat washers. Attach the remaining rail plate with the round mounting holes using an M8-1.25 x 20 cap screw, 8mm lock washer and 8mm flat washer (figure Model g0513X2B (Mfg. since 5/11) Flat Washer Knob lock Washer...
  • Page 11 Model g0513X2B (Mfg. since 5/11) secure the guide post handwheel onto the flat part of the handwheel shaft with the M6-1 x 20 cap screw.
  • Page 12 —if the bandsaw starts, immediately discon- nect power. the switch disabling feature is not working correctly. this safety feature must work properly before proceeding with regular operations. Call tech support for help. Model g0513X2B (Mfg. since 5/11)
  • Page 13 (see figure 3 on page 10). Model g0513X2B (Mfg. since 5/11) Adjust the fence face parallel with the edge of the miter slot, as shown in figure 8.
  • Page 14 (figure 10) and set the pointer in line with "0" and the measurement scale on the table. pointer nut figure 10. Calibrating fence pointer (screw out of view). re-tighten the pointer adjustment nut. Model g0513X2B (Mfg. since 5/11) pointer...
  • Page 15 Apply a few dabs of a light all-purpose grease to the threads. re-adjust tracking (see blade tracking on g0513X Manual page 22). Model g0513X2B (Mfg. since 5/11) to lubricate the tension adjustment assem- bly: disConneCt BAndsAW FroM poWer! open the top wheel cover and look through the top of the wheel.
  • Page 16 Model g0513X2B (Mfg. since 5/11) screw Motor...
  • Page 17 You can view these pages in color at www.grizzly.com. Model g0513X2B (Mfg. since 5/11) WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious per- sonal injury, fire, or machine damage. If you notice...
  • Page 18 17. Magnetic switch. figure 15. Control panel wiring. figure 16. Motor wiring. READ ELECTRICAL SAFETY -18- Model g0513X2B (Mfg. since 5/11) ON PAGE 17!
  • Page 19 Wiring diagram 220v, 1-ph POWER SUPPLY JUNCTION L1/1 L2/3 MA-18 T1/2 T2/4 RA-20 8-12 MAGNETIC SWITCH see figure Model g0513X2B (Mfg. since 5/11) Ground L3/5 NO13 NC15 NC16 T3/6 NO14 Ground Capacitor 45MFD 450VAC Ground 220 VAC 6-15 PLUG...
  • Page 20 -20- Model g0513X2B (Mfg. since 5/11)
  • Page 21 START SWITCH P0513X2B042 SWITCH CORD P0513043 SWITCH CORD PCAP11M CAP SCREW M8-1.25 X 16 PWF08M FENDER WASHER 8MM P0513046 UPPER WHEEL SLIDING BRACKET Model g0513X2B (Mfg. since 5/11) main parts list PART # PCAP06M P0513048 PCAP04M P0513050 P0513X2B051 P0513055 PB10M PW03M...
  • Page 22 PHLP HD SCR M4-.7 X 10 PS38M EXT TOOTH WASHER 5MM PTLW02M CONNECTING CORD P0513X2B173 -22- main parts list REF PART # P0513X2B174 P0513X2B175 PFS07M P0513X2B177 DESCRIPTION TERMINAL BOX WIRE NUT P3 FLANGE SCREW M5-.8 X 10 STRAIN RELIEF 5/16" Model g0513X2B (Mfg. since 5/11)
  • Page 23 157-6 157-7 157-8 157-2 157-4 157-13 157-9 157-5 156-2 156-4 156-3 156-1 151-6 151-5 151-8 151-9 151-7 151-10 Model g0513X2B (Mfg. since 5/11) 157-14V2 157-15 152-5V2 157-11 157-1 157-18 157-13 157-3V2 157-16 161-1 145-11 165V2 145-12 145-13 145-14 145-15 145-9...
  • Page 24 INNER RAIL PLATE PW03M FLAT WASHER 6MM PLW03M LOCK WASHER 6MM 165V2 PCAP02M CAP SCREW M6-1 X 20 PAW05M HEX WRENCH 5MM PAW08M HEX WRENCH 8MM PWR1013 WRENCH 10 X 13 FLAT WASHER 8MM PW01M Model g0513X2B (Mfg. since 5/11)
  • Page 25 155-10 P0513X2165 ANGLE LABEL 155-11 PW01M FLAT WASHER 8MM 155-12 PB07M HEX BOLT M8-1.25 X 25 155-13 P0513X101 LOCK HANDLE M8-1.25 155-14 PW05M FLAT WASHER 4MM Model g0513X2B (Mfg. since 5/11) 155-9 155-1 155-10 155-11 155-31 155-1 155-12 155-23 155-24...
  • Page 26 (800) 523-4777 or www.grizzly.com to order new labels. -26-...
  • Page 27 NOTICE refer to the newest copy of the grizzly catalog for other accessories available for this machine. replacement blades these replacement blades are milled for exact tooth set and are made with high quality tool steel.
  • Page 28 Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...
  • Page 29 MODEL G0513X/G0514X/G0514X3 EXTREME SERIES BANDSAW OWNER'S MANUAL COPYRIGHT © JANUARY, 2006 BY GRIZZLY INDUSTRIAL, INC. REVISED FEBRUARY, 2007 (TR) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
  • Page 30 ���� ������ �������� �������� ������ ������������ �� ��� ������ ������ ���������� ����������� ��� ������� �� ���� ������������������ ������� �� ����� ���������� ��� ������ ��� ������������ ����� �� ���� ������ ��� ������ �� ������� �������� ������� ��������� ����������� ������������� �� ������ ���...

  • Page 31: Table Of Contents

    Table of Contents INTRODUCTION... 3 Foreword ... 3 Contact Info ... 3 G0513X Machine Data Sheet ... 4 G0514X Machine Data Sheet ... 6 G0514X3 Machine Data Sheet ... 8 Identification ... 10 SECTION 1: SAFETY... 11 Safety Instructions for Machinery ... 11 Additional Safety Instructions for Bandsaws ...
  • Page 32 SECTION 6: MAINTENANCE ... 45 Schedule ... 45 Cleaning ... 45 Unpainted Cast Iron ... 45 Lubrication ... 45 Wheel Brush ... 45 SECTION 7: SERVICE ... 46 Troubleshooting ... 46 Checking V-Belt ... 48 Tensioning V-Belt ... 48 Replacing V-Belt ... 49 Adjusting Tension Lever ...

  • Page 33: Introduction

    Foreword We are proud to offer the Model G0513X/G0514X/ G0514X3 Extreme Series Bandsaw. This machine is part of a growing Grizzly family of fine wood- working machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer...

  • Page 34: G0513X Machine Data Sheet

    G0513X Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0513X 17" 2 HP EXTREME SERIES BANDSAW Product Dimensions: Weight... 345 lbs. Length/Width/Height... 32 x 32 x 73 in. Foot Print (Length/Width)...
  • Page 35 Table Information Table Length... 23-5/8 in. Table Width... 17-1/4 in. Table Thickness... 1-1/2 in. Floor to Table Height...37-1/2 in. Fence Information Locks in Front... Yes Locks in Rear...No Adjustable for Blade Lead...Yes Construction Table Construction...Precision Ground Cast Iron Rip Fence ... Cast Iron Fence with Extruded Aluminum Resaw Fence Base Construction...

  • Page 36: G0514X Machine Data Sheet

    G0514X Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0514X 19" 3 HP EXTREME SERIES BANDSAW Product Dimensions: Weight... 383 lbs. Length/Width/Height... 36 x 32 x 76 in. Foot Print (Length/Width)...
  • Page 37 Table Information Table Length... 26-3/4 in. Table Width... 19 in. Table Thickness... 1-1/2 in. Floor to Table Height...37-1/2 in. Fence Information Locks in Front... Yes Locks in Rear...No Adjustable for Blade Lead...Yes Construction Table Construction...Precision Ground Cast Iron Rip Fence ... Cast Iron Fence with Extruded Aluminum Resaw Fence Base Construction...

  • Page 38: G0514X3 Machine Data Sheet

    G0514X3 Machine Data Sheet Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0514X3 19" 3 HP 3-PHASE EXTREME SERIES Product Dimensions: Weight... 378 lbs. Length/Width/Height... 36 x 32 x 76 in. Foot Print (Length/Width)...
  • Page 39 Table Information Table Length... 26-3/4 in. Table Width... 19 in. Table Thickness... 1-1/2 in. Floor to Table Height...37-1/2 in. Fence Information Locks in Front... Yes Locks in Rear...No Adjustable for Blade Lead...Yes Construction Table Construction...Precision Ground Cast Iron Rip Fence ... Cast Iron Fence with Extruded Aluminum Resaw Fence Base Construction...

  • Page 40: Identification

    Figure 1. Bandsaw front view. A. Tension Indicator Window B. ON/OFF Switch C. Rip Fence D. Fence Locking Lever E. Dust Port 4" Miter Gauge G. Blade Tension Handwheel H. Ball Bearing Roller Guides Guide Post Guide Post Handwheel K. Blade Tracking Window -10- Identification Figure 2.

  • Page 41: Section 1: Safety

    SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages.
  • Page 42 Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructions are safe and clearly understood. 8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe dis- tance from the work area. 9.

  • Page 43: Additional Safety Instructions For Bandsaws

    Additional Safety Instructions for Bandsaws BLADE CONDITION. Do not operate with dull, cracked or badly worn blade. Dull blades require more effort to use and are difficult to control. Inspect blades for cracks and missing teeth before each use, and replace as required.

  • Page 44: Section 2: Circuit Requirements

    SECTION 2: CIRCUIT REQUIREMENTS Operation Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so. Amperage Draw The motor for your machine may draw the follow- ing amps at maximum load.

  • Page 45: Grounding

    Figure 5. NEMA 6-20 plug and receptacle. Figure 6. NEMA L15-20 plug and receptacle. This machine must have a ground prong in the plug to help ensure that it is grounded. DO NOT remove ground prong from plug to fit into a two-pronged outlet! If the plug will not fit the outlet, have the proper outlet installed by a qualified electrician.

  • Page 46: Section 3: Set Up

    SECTION 3: SET UP Set Up Safety This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire set up pro- cess! This is an extremely heavy machine.

  • Page 47: Inventory

    Inventory After all the parts have been removed from the crate, you should have the following items: Crate Contents (Figure 7 & 8): A. Bandsaw (not shown) ... 1 B. Table ... 1 C. Miter Gauge ... 1 D. Back Square Tube ... 1 E.

  • Page 48: Hardware Recognition Chart

    Hardware Recognition Chart -18- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 49: Clean Up

    Remove this protective coating with a sol- vent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For opti- mum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated.

  • Page 50: Moving & Placing Base Unit

    Moving & Placing Base Unit This is an extremely heavy machine. Serious personal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and a forklift or a hoist when removing the machine from the crate. Use a chain or a lifting strap with a minimum of 1000 lbs.

  • Page 51: Table

    Table The table is heavy and requires two people to lift it onto the trunnions. The saw blade should also be removed to make table installation easier. Components and Hardware Needed: Table ... 1 Hex Bolts M8-1.25 x 16 ... 4 Lock Washers 8mm ...

  • Page 52: Blade Tracking

    Blade Tracking Personal injury or death can occur if the machine starts while your hand is touching the bandsaw wheel during tracking adjustments. Disconnect power from the bandsaw before performing blade tracking adjustments. The blade tracking is primarily affected by the tilt of the upper wheel, also known as "Center Tracking";...

  • Page 53: Positive Stop

    Figure 18. Blade tracking controls. G0513X/G0514X/G0514X3 Extreme Series Bandsaw Positive Stop Personal injury or death can occur if the bandsaw starts during table adjust- ments. Disconnect power from the bandsaw before performing table adjust- ments. The positive stop allows the table to be quickly and accurately returned to the horizontal (0˚) position after being adjusted to a different angle.

  • Page 54: Dust Collection

    To set the positive stop: DISCONNECT BANDSAW FROM POWER! Adjust the blade tension until the mark on the blade tension scale is between 4 and 6. Loosen the hex nut that locks the positive stop bolt in place. Raise the guide post and place a machinist’s square on the table next to the side of the blade as illustrated in Figure 20.

  • Page 55: Installing Fence

    Installing Fence Components and Hardware Needed: Fence Assembly ... 1 Back Square Tube ... 1 Front Rail ... 1 Resaw Fence ... 1 Cap Screws M6-1 x 16 ... 2 Hex Bolts M6-1 x 20 ... 2 Lock Washers 6mm ... 2 Flat Washers 6mm ...

  • Page 56: Test Run

    Slide the resaw fence over the moving plate, as shown in Figure 25, so the moving plate fits inside the channel of the resaw fence. Resaw Fence Lock Handle Figure 25. Attaching resaw fence to standard fence. Tighten the lock handle. Pull the fence handle up and place the fence assembly on the fixed rail as shown in Figure Figure 26.

  • Page 57: Tensioning Blade

    Tensioning Blade A properly tensioned blade is essential for mak- ing accurate cuts and is required before mak- ing many bandsaw adjustments. (Everytime you replace the blade, you should perform this proce- dure because all blades tension differently.) To tension the bandsaw blade: Complete the Test Run procedure and make sure the blade is tracking properly.
  • Page 58 Bandsaw Blade Top View Figure 28. Blade should be perpendicular (90˚) to the face of the support bearing. Tighten the assembly cap screw. Loosen the cap screw on the support bearing adjustment shaft. Place a 0.016" feeler gauge between the support bearing and the blade, and position the bearing 0.016"...

  • Page 59: Adjusting Blade Guide Bearings

    Check to make sure the guide block assem- bly is perpendicular with the face of the sup- port bearing as illustrated in Figure 28. —If the guide block assembly is perpen- dicular to the face of the support bearing, continue on to the next step. —If the guide block assembly is not per- pendicular to the support bearing, loosen the guide block assembly cap screws and...

  • Page 60: Aligning Table

    NOTICE Make sure that the blade teeth will not con- tact the guide bearings when the blade is against the rear support bearing during the cut or the blade teeth will be ruined. Tighten the cap screw on the lateral adjust- ment rod.

  • Page 61: Aligning Fence

    Aligning Fence To ensure cutting accuracy when the fence is first installed, the fence should be aligned with the miter slot. To align the fence parallel with the miter slot: If the fence is mounted on the left-hand side of the blade, remove it and remount it next to the miter slot.

  • Page 62: Section 4: Operations

    OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training. -32-...

  • Page 63: Start/Stop Switch

    Guide Post Lock Knob -33- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 64: Fine Tune Tracking

    Fine Tune Tracking NOTICE Adjusting the final blade tracking setting requires the machine to be turned ON. To fine tune the tracking: Close the wheel covers and turn the bandsaw Observe the blade tracking path through the clear window on the right edge of the bandsaw as shown in Figure 40.
  • Page 65 Clamp the board to the bandsaw table with- out moving it. Now slide the fence over to the board so it barely touches one end of the board. Loosen the four cap screws on top of the fence. Skew the fence so it is parallel to the edge of the scrap piece.

  • Page 66: Ripping

    Ripping Ripping is the process of cutting with the grain of the wood stock. For plywood and other pro- cessed wood, ripping simply means cutting down the length of the workpiece. To make a rip cut: Adjust the fence to match the width of the cut on your workpiece and lock the fence in place.

  • Page 67: Resawing

    Resawing Resawing (Figure 45) is the process of cutting a board into two or more thinner boards. The maxi- mum board width that can be resawn is limited by the maximum cutting height of the bandsaw. One of the most important considerations when resawing is blade selection.

  • Page 68: Cutting Curves

    Cutting Curves When cutting curves, simultaneously feed and turn the stock carefully so that the blade follows the layout line without twisting. If a curve is so abrupt that it is necessary to repeatedly back up and cut a new kerf, use either a narrower blade or a blade with more TPI (teeth per inch), or make more relief cuts.

  • Page 69: Blade Speed

    Blade Speed The blade speed can be adjusted to 1700 or 3500 FPM. Speed adjustments are made by moving the V-belt position on the motor and wheel pul- leys. Most woodcutting can be performed successfully at the higher blade speeds. Slower blade speeds generally produce better results when cutting hardwoods, intricate curves, or when an excep- tionally smooth cut is desired.

  • Page 70: Blade Information

    Blade Information Selecting the right blade requires a knowledge of the various blade characteristics to match the blade with the particular cutting operation. Blade Length Measured by the circumference, blade lengths are usually unique to the brand of your bandsaw and the distance between wheels.
  • Page 71 Hook: The teeth on this style have a posi- • tive angle (downward) which makes them dig into the material, and the gullets are usu- ally rounded for easier waste removal. These blades are excellent for the tough demands of resawing and ripping thick material. Tooth Pitch Usually measured as TPI (teeth per inch), tooth pitch determines the size of the teeth.

  • Page 72: Blade Changes

    Blade Changes Always disconnect power to the machine when changing blades. Failure to do this may result in serious personal injury. All saw blades are dan- gerous and may cause personal injury. To reduce the risk of being injured, wear leather gloves when handling saw blades.

  • Page 73: Section 5: Accessories

    SECTION 5: ACCESSORIES Replacement Blades These replacement blades are milled for exact tooth set and are made with high quality tool steel. ⁄ " Carbon Steel Replacement Blades for the Model G0513X MODEL WIDTH H4803 1/8" 14 RAKER H4804 1/4" H4805 1/4"...
  • Page 74 G7984—Face Shield H1298—Dust Sealed Safety Glasses H1300—UV Blocking, Clear Safety Glasses H2347—Uvex Spitfire Safety Glasses ® H0736—Shop Fox Safety Glasses ® Safety Glasses are essential to every shop. If you already have a pair, buy extras for visitors or employees. You can't be too careful when it comes to shop safety! H2347 G7984...

  • Page 75: Section 6: Maintenance

    SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. Schedule For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions given in this section. Daily Check: •...

  • Page 76: Section 7: Service

    SECTION 7: SERVICE This section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If you need help troubleshooting, you need replacement parts, or you are unsure of how to perform the pro- cedures in this section, then feel free to call our Technical Support at (570) 546-9663.
  • Page 77 Symptom Possible Cause Machine 1. Blade weld hits guides or teeth are broken. vibration 2. Bent or worn out blade. noisy operation 3. Motor or component is loose. when running. 4. V-belt worn or loose. 5. Motor fan is rubbing on fan cover. 6.

  • Page 78: Checking V-Belt

    Checking V-Belt To ensure optimum power transmission from the motor to the blade, the V-belt must be in good condition and operate under proper tension. The belt should be checked for cracks, fraying, and wear. Belt tension should be checked at least every 3 months—more often if the bandsaw is used daily.

  • Page 79: Replacing V-Belt

    Replacing V-Belt Tools Needed: Hex Wrench 6mm ...1 Wrench 13mm ...1 To replace the V-belt: DISCONNECT BANDSAW FROM POWER! Open both wheel covers, and remove the blade. Loosen the motor mount screws shown in Figure 58. Unthread the wheel mount bolt shown in Figure 59 and slide the lower wheel off of the bearing shaft.

  • Page 80: Adjusting Tension Lever

    Adjusting Tension Lever The tension lever has an adjustment screw that allows you to adjust how much tension is released when the lever is used. Tools Needed: Hex Wrench 6mm ... 1 Hex Wrench 5mm ... 1 To adjust the tension lever: DISCONNECT BANDSAW FROM POWER! Loosen the tension lever and remove the blade.

  • Page 81: Wheel Alignment

    Wheel Alignment Components and Hardware Needed: 60" Long 2x4 ... 1 Tools Needed: Wrench 13mm ... 1 Tape Measure ... 1 Coplanarity Gauge (see Figure 62) ... 1 Wheel alignment is one of the most critical factors for optimal performance from your bandsaw. Heat, vibration, wandering, blade wear, tire wear and overall bandsaw wear are considerably decreased when the wheels are properly aligned...
  • Page 82 Adjust the tracking knob to get both wheels parallel. If the wheels won’t go parallel to each other, then move the lower wheel at the adjustment hub (Figure 64) so they line up. If the wheels will go parallel but not coplanar, shim the required wheel out as necessary, using thin ⁄...

  • Page 83: G0513X Electrical Components

    G0513X Electrical Components Switch Wiring To Power Supply To Motor Motor Wiring -53- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 84: G0513X Wiring Diagram

    G0513X Wiring Diagram G0513X Wiring Diagram ������������������� ����� ������� ����� ��� ����� ��������������� � ����� ��������������� � ����� ��������������� � ����� ������� -54- ����� ������ ������ �������� � � � �������� ������ �������� � � � G0513X/G0514X/G0514X3 Extreme Series Bandsaw ������...

  • Page 85: G0514X Electrical Components

    G0514X Electrical Components Power Supply Junction Block Motor Wiring Control Panel Wiring Magnetic Switch To Junction Box Wiring POWER To Motor To Control Panel -55- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 86: G0514X Wiring Diagram

    G0514X Wiring Diagram ������ �� �� � � � � � � � � ������ � � � � ���� ���� ���� � ���� ���� ���� ��� ��� ��� � � ������ � � � -56- ������ ������� ��������� ����� �...

  • Page 87: G0514X3 Electrical Components

    G0514X3 Electrical Components Power Supply Junction Block Control Panel Wiring POWER G0513X/G0514X/G0514X3 Extreme Series Bandsaw Motor Wiring (220V) Magnetic Switch To Junction Box Wiring To Motor To Control Panel -57-...

  • Page 88: G0514X3 Wiring Diagram

    G0514X3 Wiring Diagram G0514X3 Wiring Diagram ������ �� �� �� � � � � � � ������ � � � � � � ���� ���� ���� ��� ���� ���� ���� ��� ��� ��� � � � ������ � � � �...

  • Page 89: G0513X Main Parts

    G0513X Main Parts -59- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 90: G0513X Fence/Guide Parts

    G0513X Fence/Guide Parts ������ ������ ������ ������ ������ ����� ������ ������ ������ ����� ����� ����� ����� ������ ��� ��� ��� ��� ��� �� ��� �� ��� �� ��� ��� �� ��� ��� ��� ������ ������ -60- ������ ������ ����� ������ ������...

  • Page 91: G0513X Parts List

    G0513X Parts List REF PART # DESCRIPTION P0513X001 BUSHING PSS01M SET SCREW M6-1 X 10 P0513X003 BUSHING P0513004 LIFTING EYE BOLT M10-1.5 P0513005 MACHINE BODY PSS07M SET SCREW M5-.8 X 5 P0513X007 BUSHING PW03M FLAT WASHER 6MM PWRCRD220L POWER CORD PN01M HEX NUT M6-1 P0513011...
  • Page 92 PART # DESCRIPTION PN02M HEX NUT M10-1.5 P0513100 SMALL GEAR P0513X101 LOCK HANDLE P0513102 TRUNNION SUPPORT BRACKET PLW06M LOCK WASHER 10MM PW04M FLAT WASHER 10MM PB18M HEX BOLT M6-1 X 20 PSB37M CAP SCREW M6-1 X 50 P0513107 PILLOW BLOCK PN01M HEX NUT M6-1 P0513109...

  • Page 93: G0513X Labels

    MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. ���...

  • Page 94: G0514X/G0514X3 Main Parts

    G0514X/G0514X3 Main Parts -64- G0513X/G0514X/G0514X3 Extreme Series Bandsaw...

  • Page 95: G0514X/G0514X3 Fence/Guide Parts

    G0514X/G0514X3 Fence/Guide Parts ������ ������ ������ ������ ������ ����� ������ ������ ����� ����� ����� ������ ������ ������ ��� ��� ��� ��� �� �� ��� ��� ��� ��� �� ��� ��� ��� G0513X/G0514X/G0514X3 Extreme Series Bandsaw ������ ������ ������ ����� ������ ������...

  • Page 96: G0514X/G0514X3 Labels

    MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -66- ���...

  • Page 97: G0514X/G0514X3 Parts List

    G0514X/G0514X3 Parts List REF PART # DESCRIPTION PSS01M SET SCREW M6-1 X 10 PFS07M FLANGE SCREW M5-.8 X 10 P0513X003 BUSHING P0513004 LIFTING EYE BOLT M10-1.5 P0514005 MACHINE BODY PSS07M SET SCREW M5-.8 X 5 P0513X007 BUSHING PW03M FLAT WASHER 6MM PN01M HEX NUT M6-1 P0513011...
  • Page 98 G0514X/G0514X3 Parts List PART # DESCRIPTION PB32M HEX BOLT M10-1.5 X 25 PLW06M LOCK WASHER 10MM P0513085 MOTOR BRACKET PSBS01M BUTTON HD CAP SCR M8-1.25 X 20 P0513087 PLATE PFS07M FLANGE SCREW M5-.8 X 10 P0513089 PILLOW BLOCK PK15M KEY 5 X 5 X 35 PB81M HEX BOLT M8-1.25 X 20 LH P0514X092...
  • Page 99 FLANGE SCREW M5-.8 X 12 PTLW02M EXT TOOTH WASHER 5MM P0514X201 G0514X MODEL # LABEL P0514X3201 G0514X3 MODEL # LABEL G8589 GRIZZLY LOGO PLATE PLABEL-11 SAFETY GLASSES LABEL PLABEL-20 OPEN DOOR LABEL P0513X205 GUARD ADJ LABEL PLABEL-12 READ MANUAL LABEL...

  • Page 100: Warranty And Returns

    WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
  • Page 101 ���������������������������������������������������������������������������������� � ������������������������������������������������������������������������������������ ����� ����������������������� ������ � ������������������������ ���� ��������������������� ���������������������������� ������ ������������������������ ���������� � ���������������� ���������������������������� ������������������������������� ��������������������������� ��� ��������� ����������� �� ����� �� � ��������� ������ �� ���� �� ���� ��� ��������� �������� �� ���� �� ������� ������ �������� ��� ��������� �� ������� ��� ����������� �� �������� ������������� ���...
  • Page 102 ���������������������� ���������������������� ����������������������������������� ����������������������������������� ������������������������������������� �������������������������������������� ������� ����������� ���� ���� ��� ���� ����������� �� ���������� �������������������������������������� ����� ����� ����...
  • Page 104 Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...

Table of Contents