DSC PowerSeries Neo LE2080 Installation Manual page 63

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même sile brouillage est susceptible d'en compromettre le fonctionnement.
Wireless Notice
Thisequipment complieswith FCC and IC radiation exposure limitsset forth for an uncontrolled environment. The antenna should be installed and oper-
ated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Cet appareilest conforme auxlimitesd'exposition auxrayonnementsde la IC pour un environnement non contrôlé. L'antenne doit être installé de façon
à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps. L'émetteur ne doit pas être colocalisé nifonctionner
conjointement avecà autre antenne ou autre émetteur.
Antenna gain must be below / Gain de l'antenne doit être ci-dessous:
Frequency Band/Bande de fréquence
GSM850 / FDD V
PCS1900 / FDD II
LTEB2
LTEB4
LTEB5 / B12 / B13
FCC Class B digital device notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different fromthat to which the receiver isconnected.
- Consult the dealer or an experienced radio/TVtechnician for help
CAN ICES-3 (B) / NMB-3 (B)
TL2803G(R)E -EU /3G2080(R)E- EU/TL280(R)E
FCC ID:F5316TL2803GRE
IC: 160A-TL2803GRE
Notes for EN50131-1:2006/A1:2009 Compliant installations:
Models TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)Eare an SPT Type Y- the module is mounted within CIEor PShousing and it receives power from
the compatible CIE or Power Supply source that are in compliance with EN50131-6:2008 Type A requirements for a Grade 2, Class II application. This
product hasno replacement partsand software programmable optionsare accessible at level3 (installer mode), section [851].
The TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)E connects to compatible DSC alarm control panels using the DSC proprietary serial interface and
protocolPC-Link (converted also to RS- 422). The module operates in pass-through mode and it does acknowledge the alarmto the compatible control
panelafter an acknowledgement hasbeen received fromthe compatible alarmreceiver.
1. The TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)Emodule ismonitored bythe controlpaneland it isprogrammed via the programming menu
(* 8, section [851] in the controlpanel. The interface isconnected to the PC-Linkbusasshown in the diagramincluded in thismanual.
2. The HSPA3G Cellular path isimmune to conducted and radiated RF fieldswith levelsup to 10V/mastested per EN50130- 4 Standard.
3. The TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)Emodule conformswith radiated emissionslevelsfor ClassBequipment asper standards
EN61000- 6-3/EN55022/CISPR22.
4. The TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)Emodule usesAES128 encryption and heartbeat supervision for HSPA3G Cellular com-
munication pathsand it meetssecuritylevelsS2 asper EN50136-2:2013. It also usesauthentication for each message exchanged with the
compatible receiver equipment at ARC and it meetslevelI2 for information security.
5. The 3G2080(R)E-EU module hasonlyone communication path:
HSPA3G Cellular communication path using 900/1800/2100MHzPublicCellular Network. The HSPA3G Cellular communication path that can
be used in a standalone mode in conjunction with a DSC alarmsystem(compatible DSC alarmcontrolpanelmodels: HS2128/064/032/016).
The supported ATSconfiguration is: customcategoryC.
6. The TL280(R)Emodule hasonlyone communication path: Ethernet communication path using Internet. The communication path that can be
used in a standalone mode in conjunction with a DSC alarmsystem(compatible DSC alarmcontrolpanelmodels: HS2128/064/032/016). The
supported ATSconfiguration is: customcategoryC.
7. The TL2803G(R)E-EU module hastwo communication paths: HSPA3G Cellular communication path using 900/1800/2100MHzPublicCellular
Networkand Ethernet communication path using Internet. The communication pathscan be used in a standalone mode in conjunction with a
DSC alarmsystem(compatible DSC alarmcontrolpanelmodels: HS2128/064/032/016). The supported ATSconfiguration is: customcategory
C.
8. TL2803G(R)E-EU/3G2080(R)E-EU/TL280(R)Ehasbeen tested for compliance in conjunction with the following applicable standards:
EN50136-1:2012, EN50136- 2:2013, EN50131-10:2014, ATSconfiguration: C.
For EN50131- 1:2006/A1:2009 compliant installations, the following programming optionsshallbe set asdescribed.
Supervision Heartbeat: shallbe set to 180 seconds
NOTE: The compatible receiver at ARC location shall have supervision window programmed for 180 seconds. TL2803G(R)E-EU/3G2080 (R)E-
EU/TL280(R)E has been certified by TELEFICATION in accordance with EN50131-1:2006/A1:2009, EN50131-10:2014 requirements for Grade 2,
ClassII and EN50136-2:2013 Configuration: C
ATS Custom Category C
EN50136-1:2012 AnnexD Table D.1
EN50136-1:2012 AnnexD Table D.2
EN50136-1:2012 AnnexD Table D.3
EN50136-1:2012 AnnexD Table D.4
EN50136-1:2012 AnnexD Table D.5
TL2803GRE, TL2803GE, 3G2080RE, 3G2080E
2.26 dBi
2.41 dBi
-
-
-
LE2080(R)/TL280LE(R
FCC ID:F5317TL280LER
IC:160A-TL280LER
Level
D3
M3
T4
A4 (Depending on cellular carrier used)
S2 (use AES- 128 and authentication/sequential information in each
message transmitted to the SG receiver)
63
TL280LE, TL280LER, LE2080, LE2080R
)
-
-
2.76 dBi
2.82 dBi
2.45 dBi