Detailed Specifications - JBL ES250PW Service Manual

ES250PW
ES250PW
LINE VOLTAGE
US 120vac/60Hz
EU 230vac/50-60Hz
Parameter
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
AVG System impedance
Min System impedance
Rated Output Power (120VAC)
AVG RMS Dynamic Power
THD @ Rated Power
THD @ 1 Watt
DC Offset
Damping factor
Input Sensitivity
Input Frequency
L or R
LFE input
System Gain (L or R inputs)
System Gain (LFE input)
Signal to Noise
SNR-A-Weighted
SNR-unweighted
Residual Noise Floor
Input Impedance
Line Input (L, R,LFE)
Filters
LP filter Variable (Normal mode)
Subsonic filter (HPF) 2nd Order
Friend circuit
LFE Low pass
Limiter
THD at Max. Output Power
Features
Volume pot Taper (lin/log)
Phase switch
LP Filter defeat switch
Wireless ready
Wireless channels
LED Indicator
Input Configuration
Line in (L,R) & LFE
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input test frequency
ATO Line level input
Downloaded from www.Manualslib.com
250W Powered Sub Amp
Yes/No Hi/Lo Line
Yes 108-132
Yes 207-253
Specification Unit
D n/a
4 Ohms
7.25 Ohms
4.385 Ohms
250 Watts
336 Watts
0.5 %
0.2 %
10 mV-DC
>50 DF
50 Hz
13 mVrms
7 mVrms
43.7 dB
49.1 dB
80 dBA
65 dBr
<1.5
mVrms(max)
10K ohms
50-150 Hz
Fixed
Fixed
200>LP<500 Hz
5 %
--
LOG --
0-180 deg
YES
YES
4 n/a
YES
YES --
YES
50 Hz
1.5 mV
manuals search engine
Nom. Unit
120 Vrms
230 Vrms
QA Test
Conditions
Limits
n/a
n/a Nominal
n/a AP Computed BW 20 to 500Hz
n/a @ 92Hz
240
Reference 200mV driven into LFE input
1 22K filter
0.3 22K filter
30 @ Speaker Outputs
Measured at amplifier board 90%
20
of full power
50 Nominal Freq.
±1dB To 1 Watt, AP Zo=600
±1dB To 1 Watt, AP Zo=600
Reference
Reference
75 relative to 1W
60 relative to 1W
Volume @max, w/ A/P Swept
2.5 Bandpass Measurement (Line
freq.+ harmonics) (BW=20 KHz)
n/a Nominal
± 10
LFE input driven only
Drive unit 6dB above the required
level to obtain full power
functional
Approximately 800mV single input
driven, L or R input
functional
functional
functional
functional
functional
functional
functional
functional
functional
functional
2
Notes
Normal Operation
Normal operation, MOMS required
Notes
Domestic version only 120 VAC-60 Hz
Average RMS power, 3/20 Cycles 50 Hz,
Driven 6dB above its input sensitivity ,
average of the RMS value for the first 4
consecutive peaks
Measured at the speaker cable. 225 Watts @
THD < 0.1 % @ 50 Hz
Single input driven, either L or R
LFE input driven only.
Single input driven L or R inputs (Local inputs)
Single input driven LFE, local input
A-Weighting filter
22K filter
Line level inputs must be terminated using
1KOHM
4th Order variable-24 db/Octave
Maximum THD as a result of limiting.
A Taper
Disables LP filter, Wireless mode only, it has
no effect when using local inputs
Refer to Wireless section below
System is provided with 4 wireless channels,
which can be selected via a rear panel switch,
channel should match ID at Tx side
RED-Standby, GRN-Active, ORG-Wireless
link and subwoofer are active.
3 RCA Jacks, RED, WHT (Left and Right) and
Purple for LFE
Maximum acceptable level.