Dremel 200 series Original Instructions Manual page 22

ONLY FOR EC COUNTRIES
Do not dispose of power tools with household
waste!
According the European Guideline 2012/19/EC
for Waste Electrical and Electronic Equipment
and its implementation into national law, power tools that
are nolonger usable must be collected separately and
disposed of in an environmentally-correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Rated power . . . . . . . . . . 125 W
Voltage Rating 220-240 V, 50-60 Hz
. . . . . . . . . . . .
Collet Capacity 0,8mm, 1,6mm, 2,4mm, 3,2mm
. . . . . . . . . . .
Rated speed (n( . . . . . . . . 35000 min
Class II construction . Double insulated construction
tools
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING
THE TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can
be used to perform detailed and intricate tasks. The wide
range of Dremel accessories and attachments allow you to
perform a large variety of tasks. These include tasks such
as sanding, carving and engraving, cutting, cleaning and
polishing.
PICTURE 1
PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Attachment interface
E. Shaft Lock Button
F. Ventilation openings
G. Hanger
H. Power cord
I. On/Off Switch and Speed Dial
J. Brush cover (one each side(
COLLETS
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identified by the rings on the back of the collet.
PICTURE 3
K. 3,2 mm Collet without ring
L. 2,4 mm Collet with three rings
M. 1,6 mm Collet with two rings
N. 0,8 mm Collet with one ring
Always use the collet that matches the shank size of the
accessory you plan to use. Do not force a larger diameter
shank into a smaller collet.
PICTURE 4
O. Shaft Lock Button
P. Collet Wrench
Q. To tighten
R. To loosen
S. Collet Nut
1. Press the shaft lock button, hold down and rotate the
2. With the shaft lock button engaged, loosen and
3. Remove the collet by pulling it free from the shaft.
-1
4. Install the appropriate size collet fully into the shaft
PICTURE 5/6/6B
T. Shaft Lock Button
1. Press the shaft lock button and rotate the shaft by
2. With the shaft lock button engaged, loosen (do
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, finger tighten the
NOTE: Be sure to read the instructions supplied with your
Dremel accessory for further information on its use.
Use only Dremel tested, high performance accessories.
The first step in using the multitool is to get the "feel" of it.
Hold it in your hand and feel its weight and balance. Feel
the taper of the housing. This taper permits the tool to be
grasped much like a pen or pencil. The unique softgrip on
the nose allows for added comfort and control during use.
Always hold the tool away from your face. Accessories
can be damaged during handling and can fly apart as they
come up to speed.
When holding tool, do not cover the ventilation openings
with your hand. Blocking the ventilation openings could
cause the motor to overheat.
IMPORTANT! Practice on scrap material first to see how
the tool's high-speed action performs. Keep in mind that
your multitool will perform best by allowing the speed,
along with the correct Dremel accessory and attachment,
to do the work for you. Do not put pressure on the
tool during use, if possible. Instead, lower the spinning
accessory lightly to the work surface and allow it to touch
the point at which you want to begin. Concentrate on
22
CHANGING COLLETS
shaft by hand until it engages the shaft. Do not engage
the shaft lock button while multitool is running.
remove the collet nut. Use the collet wrench if
necessary.
and reinstall the collet nut finger tight. Do not fully
tighten the nut when there is no bit or accessory
installed.
CHANGING ACCESSORIES
hand until it engages the shaft lock. Do not engage the
shaft lock button while multitool is running.
not remove( the collet nut. Use the collet wrench if
necessary.
collet nut until the bit or accessory shank is gripped by
the collet.
GETTING STARTED
USE