Cisco MDS 9216 Configuration Manual page 94

Sample Configuration
switch2(config)# fcdomain domain 13 static vsan 13
switch2(config)# fcdomain domain 14 static vsan 14
switch2(config)# fcdomain domain 40 static vsan 20
Configure the SVC interface into the correct VSANs in Switch 2.
Step 4
switch2(config)# int svc 2/1 - 2
switch2(config-if)# no initiator vsan 1
switch2(config-if)# initiator vsan 12
switch2(config-if)# no target vsan 1
switch2(config-if)# target vsan 13
switch2(config-if)# no mgmt vsan 1
switch2(config-if)# mgmt vsan 14
switch2(config-if)# exit
Set the default zone configuration for the transit VSAN in Switch 2.
Step 5
switch1(config)# no zone default-zone permit vsan 20
Configure the target and SVC initiators in a zone in Switch 2.
Step 6
switch2(config)# zone name z_12 vsan 12
switch2(config-zone)# member pwwn 20:07:00:a0:b8:0f:6c:34
switch2(config-zone)# member pwwn 23:30:00:05:30:00:8d:e2
switch2(config-zone)# member pwwn 23:31:00:05:30:00:8d:e2
switch2(config-zone)# exit
switch2(config)# zoneset name zs_12 vsan 12
switch2(config-zoneset)# member z_12
switch2(config-zoneset)# exit
switch2(config)# zoneset activate name zs_12 vsan 12
Zone set activation is now initiated. Check zone status.
Configure the initiator and SVC targets in a zone in Switch 1.
Step 7
switch2(config)# zone name z_13 vsan 13
switch2(config-zone)# member pwwn 21:00:00:e0:8b:09:f0:04
switch2(config-zone)# member pwwn 23:32:00:05:30:00:8d:e2
switch2(config-zone)# member pwwn 23:33:00:05:30:00:8d:e2
switch2(config-zone)# zoneset name zs_13 vsan 13
switch2(config-zoneset)# member z_13
switch2(config-zoneset)# zoneset activate name zs_13 vsan 13
Zone set activation is now initiated. Check zone status.
Configure the SVC management N ports in a zone in Switch 1.
Step 8
switch2(config)# zone name z_14 vsan 14
switch2(config-zone)# member pwwn 23:34:00:05:30:00:8d:e2
switch2(config-zone)# member pwwn 23:35:00:05:30:00:8d:e2
switch2(config-zone)# zoneset name zs_14 vsan 14
switch2(config-zoneset)# member z_14
switch2(config-zoneset)# zoneset activate name zs_14 vsan 14
Zone set activation is now initiated. Check zone status.
Step 9 Enable and configure IVR using the switch WWNs (see Step 1 in the previous procedure).
switch2(config)# ivr vsan-topology database
switch2(config-ivr-topology-db)# autonomous-fabric-id 1 switch-wwn 20:00:00:05:30:00:41:de
vsan-ranges 2,4,20
switch2(config-ivr-topology-db)# autonomous-fabric-id 1 switch-wwn 20:00:00:05:30:00:07:1e
vsan-ranges 12,14,20
switch2(config-ivr-topology-db)# exit
switch2(config)# ivr vsan-topology activate
Set up the IVR zone to allow SVC initiators in Switch 1 to talk to the target port in Switch 2.
Step 10
switch2(config)# ivr zone name ivr_2_12
Cisco MDS 9000 Family SAN Volume Controller Configuration Guide
10-6
Chapter 10 Configuring a Dual Fabric SAN Environment
<-- target
<-- svc initiator
<-- svc initiator
<-- initiator
<-- svc target
<-- svc target
<-- svc mgmt
<-- svc mgmt
78-16119-01, Cisco MDS SAN-OS Release 1.3