Teledyne T300 Operation Manual page 20

Table of Contents
LIST OF FIGURES
Figure 3-1: Front Panel Layout .......................................................................................................................37
Figure 3-2: Display Screen and Touch Control ..............................................................................................38
Figure 3-3: Display/Touch Control Screen Mapped to Menu Charts .............................................................40
Figure 3-4: Rear Panel Layout .......................................................................................................................41
Figure 3-5: Internal Layout - T300 .................................................................................................................43
Figure 3-6: Internal Layout - T300M ..............................................................................................................44
Figure 3-7: Optical Bench Layout (shorter bench, T300M, shown) ...............................................................45
Figure 3-8: Analog In Connector ....................................................................................................................47
Figure 3-9: Analog Output Connector ............................................................................................................48
Figure 3-10: Current Loop Option Installed on Motherboard ...........................................................................49
Figure 3-11: Status Output Connector .............................................................................................................50
Figure 3-12: Control Input Connector ...............................................................................................................52
Figure 3-13: Concentration Alarm Relay ..........................................................................................................53
Figure 3-14: Rear Panel Connector Pin-Outs for RS-232 Mode ......................................................................56
Figure 3-15: Default Pin Assignments for CPU COM Port connector (RS-232) ..............................................57
Figure 3-16: Jumper and Cables for Multidrop Mode .......................................................................................59
Figure 3-17: RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram .....................................................60
Figure 3-18: Pneumatic Connections-Basic Configuration-Using Bottled Span Gas .....................................63
Figure 3-19: Pneumatic Connections-Basic Configuration-Using Gas Dilution Calibrator .............................63
Figure 3-20: T300/T300M Internal Gas Flow (Basic Configuration) ................................................................65
Figure 3-21: Pneumatic Connections - Option 50A: Zero/Span Calibration Valves ........................................66
Figure 3-22: Internal Pneumatic Flow OPT 50A - Zero/Span Valves ..............................................................67
Figure 3-23: Pneumatic Connections - Option 50B: Ambient Zero/Pressurized Span Calibration Valves .....68
Figure 3-24: Internal Pneumatic Flow OPT 50B - Zero/Span/Shutoff Valves .................................................69
Figure 3-25: Pneumatic Connections - Zero Scrubber/Pressurized Span Calibration Valves (Opt 50E) .......70
Figure 3-26: Internal Pneumatic Flow OPT 50E - Zero Scrubber/Pressurized Span ......................................71
Figure 3-27: Pneumatic Connections - Option 50H: Zero/Span Calibration Valves .......................................72
Figure 3-28: Internal Pneumatic Flow OPT 50H - Zero Scrubber/Ambient Span ...........................................74
Figure 3-29: Zero/Span Calibration Procedure ................................................................................................84
Figure 4-1: Front Panel Display ......................................................................................................................89
Figure 4-2: Viewing T300/T300M Test Functions ..........................................................................................91
Figure 4-3: Viewing and Clearing T300/T300M WARNING Messages .........................................................94
Figure 5-1: Analog Output Connector Pin Out ...............................................................................................99
Figure 5-2: COMM- Machine ID ..................................................................................................................113
Figure 5-3: Accessing the Analog I/O Configuration Submenus ..................................................................121
Figure 5-4: Setup for Checking / Calibrating DCV Analog Output Signal Levels .........................................128
Figure 5-5: Setup for Checking / Calibration Current Output Signal Levels Using an Ammeter..................130
Alternative Setup Using 250Ω Resistor for Checking Current Output Signal Levels ................132
Figure 5-6:
Figure 5-7. DIAG - Analog Inputs (Option) Configuration Menu .................................................................136
Figure 6-1: COM1[2] - Communication Modes Setup .................................................................................145
Figure 6-2: COMM Port Baud Rate ..............................................................................................................146
Figure 6-3: COMM - COM1 Test Port..........................................................................................................147
Figure 6-4: COMM - LAN / Internet Manual Configuration ..........................................................................150
Figure 6-5 : COMM - LAN / Internet Automatic Configuration (DHCP) ........................................................151
Figure 7-1: Default DAS Channel Setup ......................................................................................................171
Figure 7-2: APICOM Remote Control Program Interface .............................................................................186
Figure 7-3: APICOM User Interface for Configuring the DAS ......................................................................187
Figure 7-4: DAS Configuration Through a Terminal Emulation Program .....................................................188
Figure 9-1: Pneumatic Connections - Basic Configuration - Using Bottled Span Gas ...............................200
Figure 9-2: Pneumatic Connections - Basic Configuration - Using Gas Dilution Calibrator .......................200
Figure 9-3: Pneumatic Connections - Option 50A: Ambient Zero/Ambient Span Calibration Valves .........205
Figure 9-4: Pneumatic Connections - Option 50B: Ambient Zero/Pressurized Span Calibration Valves ...206
Figure 9-5: Pneumatic Connections - Option 50H: Zero/Span Calibration Valves .....................................206
xviii
Teledyne API - Model T300/T300M CO Analyzer
06864B DCN6314