Table of Contents
Advertisement
-
Note that the Red LED can light for a short period (10-20 seconds) when the AP or
OmniAccess AP 1200R reboots. If the RED LED comes on AND STAYS ON for more than
a minute, disconnect the AP or OmniAccess AP 1200R and call Alcatel Technical
Support.
-
From the CLI, Web Browser or ACS interface, configure the AP with its Primary Alcatel
OmniAccess Switch or Appliance name (which can be the name of the configuring
Alcatel OmniAccess Switch or Appliance) as described in the
Wireless Product
-
If required, use the CLI, Web Browser or ACS interface to customize the AP- or
OmniAccess AP 1200R-specific 802.11a, 802.11b and 802.11g network settings. Once
again, the two YELLOW/AMBER/ORANGE LEDs indicate the states of the 802.11a and
802.11b/g networks. If any part of the network is disabled, the corresponding YELLOW/
AMBER/ORANGE LED remains off.
8.
If everything works (the GREEN LED is on and the RED LED is off), reboot the AP or OmniAccess
AP 1200R and install it as described in this document. If your OmniAccess AP or OmniAccess AP
1200R fails this visual test, refer to
Guide
to return your OmniAccess APs.
Note:
When you are installing a OmniAccess AP 1200R or a Layer 3 OmniAccess AP on a
different subnet than the Alcatel OmniAccess Switch or Appliance, MAKE SURE that a DHCP
server is available on the subnet where you will be installing the AP or OmniAccess AP 1200R,
and that the subnet has a route back to the Primary Alcatel OmniAccess Switch or Appliance.
Also make sure that the route back to the Alcatel OmniAccess Wireless Switch or Appliance
has destination UDP ports 12222 and 12223 open for LWAPP communications. Ensure the
route back to the Primary Alcatel OmniAccess Switch or Appliance allows IP packet fragments.
Finally, make sure that if address translation is used, that the AP and the Alcatel OmniAccess
Switch or Appliance have a static 1-to-1 NAT to an outside address. (Port Address Translation
is not supported.)
9.
When you have installed and powered up the AP or OmniAccess AP 1200R in its final destina-
tion, verify that the LEDs are in the same state they were in at the end of Step 7. If no LEDs are
on, the AP or OmniAccess AP 1200R is most likely not receiving power. If all the LEDs blink
sequentially back and forth for more than five minutes, the AP is unable to find its Primary
Alcatel OmniAccess Switch or Appliance. Check the connection between the AP and the Alcatel
OmniAccess Switch or Appliance, and make sure the AP and the Alcatel OmniAccess Switch or
Appliance are either on the same subnet or that the AP has a route back to its Primary Alcatel
OmniAccess Switch or Appliance. Note that the OmniAccess 1200R APs at each remote location
must be on the same subnet to allow client roaming. Also, if the OmniAccess AP or OmniAccess
AP 1200R is not on the same subnet as the Alcatel OmniAccess Switch or Appliance, make sure
that a DHCP server is accessible on the same subnet as the OmniAccess AP or OmniAccess AP
1200R.
After completing
Step 2: Configuring the OmniAccess AP or OmniAccess AP 1200R Before Installation
for all OmniAccess APs and OmniAccess 1200R APs, continue with
Locations.
3/16/04
Alternate Preparing a Version 2.0 OmniAccess AP or OmniAccess AP 1200R
90-100832-000 Rev 5Alcatel OmniAccess Wireless Access Point Quick Installation Guide 12
Guide.
RMA Procedures
Alcatel OmniAccess
in the
Alcatel OmniAccess Wireless Product
Step 3: Preparing Mounting
Advertisement
Table of Contents
