Dual Mono Setup; Lfe Attenuator Setup; Sr+ Setup For Pioneer Plasma Displays - Pioneer VSX-916-K Operating Instructions Manual

Other Settings

Dual Mono Setup

Default setting: CH1
•
You can specify how dual mono encoded Dolby
Digital and DTS soundtracks should be played.
Dual mono is not widely used, but is
sometimes necessary when two languages
need to be sent to separate channels.
1 Select 'Dual Mono Setup' from the Other
Setup menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
:Return
2 Choose the setting that you want.
• CH2 – Only channel 2 is played
• CH1 CH2 – Both channels are played
through the front speakers
• CH1 – Only channel 1 is played
3 When you're finished, press RETURN .
You return to the Other Setup menu.

LFE Attenuator Setup

• Default setting: ATT 0 dB
Some Dolby Digital and DTS audio sources
include ultra-low bass tones. Set the LFE atten-
uator as necessary to prevent the ultra-low
bass tones from distorting the sound from the
speakers.
1 Select 'LFE ATT Setup' from the Other
Setup menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
:Return
2 Choose the setting that you want.
• ATT 0dB – No limiting (recommended)
• ATT 10dB – 10 dB of limiting
• LFE OFF – No sound from LFE channel
6b.Dual Mono Setup
Dual Mono [ CH1
:Finish
6c. LFE ATT Setup
LFE ATT ATT 0dB
:Finish
3 When you're finished, press RETURN .
You return to the Other Setup menu.

SR+ Setup for Pioneer plasma displays

Make the following settings if you have
connected a Pioneer plasma display to this
receiver using an SR+ cable. Note that the
number of settings available will depend on the
plasma display you've connected.
See also Using this receiver with a Pioneer
plasma display on page 61.
1 Select 'SR+ Setup' from the Other Setup menu.
6.Other Setup
a.DRC Setup
b.Dual Mono Setup
c.LFE ATT Setup
d.SR + Setup
:Return
2 Select the 'PDP Volume Control' setting
you want.
• OFF – The receiver does not control the
volume of the plasma display
• ON – When the receiver is switched to one
of the inputs that use the plasma display
(DVD/LD, or another function below), the
volume on the plasma display is muted so
only sound from the receiver is heard.
3 Assign any input source connected to the
plasma display to the corresponding input
number.
This matches the receiver's input source with a
numbered video input on the plasma display.
For example, assign DVD/LD to input-2 if you
have connected your DVD video output to video
input 2 on the plasma display.
• The Monitor Out Connect should be set
to the input that you've used to connect
this receiver to your plasma display.
6d.SR + Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-1
TV/SAT [ input-2 ]
DVR [ input-3 ]
VIDEO [ TV ]
Monitor Out Connect
[ OFF ]
:Finish
4 When you're finished, press RETURN .
You return to the Other Setup menu.
6d.SR + Setup
PDP Volume Control
OFF
PDP Input Select
DVD/LD [ input-1 ]
TV/SAT [ input-2 ]
DVR [ input-3 ]
VIDEO [ TV ]
Monitor Out Connect
[ OFF ]
:Finish
6d.SR + Setup
PDP Volume Control
[ ON ]
PDP Input Select
DVD/LD input-2
TV/SAT [ OFF ]
DVR input-3
[ ]
VIDEO TV
[ ]
Monitor Out Connect
[ OFF ]
:Finish
13
65
En