Pioneer VSX-818V User Manual [Page 72]: Resetting The Main Unit
Pioneer stereo receiver user manual.
12
Additional information
Resetting the main unit
Use this procedure to reset all the receiver's
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the ADVANCED
SURROUND button, press and hold the
STANDBY/ON button for about three
seconds.
3
When you see RESET? appear in the
display, press ' ST – '.
OK? shows in the display.
4
Press SOUND RETRIEVER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory settings.
Switching the speaker
impedance
We recommend using speakers of 8 Ω with
this system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6 Ω impedance rating.
•
With the receiver in standby, press
STANDBY/ON while holding down the
SPEAKERS button.
Each time you do this, you switch between the
impedance settings:
• SP 6 OHM – Use this setting if your
speakers are rated at 6 Ω.
• SP 8 OHM – Use this setting if your
speakers are rated at 8 Ω or more.
Note
1 Continuous average power output of 95 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than
0.2 %** total harmonic distortion (front).
* Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.
72
En
Specifications
Amplifier section
•
Continuous power output (stereo)
Front . . .95 W (20 Hz to 20 kHz, THD 0.2 %, 8
•
Rated power output
(surround / 20 Hz to 20 kHz, THD 0.06 %, 8 Ω)
Front . . . . . . . . . . . . . . . . . . . . . .95 W per channel
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 W
Surround. . . . . . . . . . . . . . . . . . .95 W per channel
•
Rated power output
(surround / 1 kHz, THD 0.05 %, 8 Ω)
Front . . . . . . . . . . . . . . . . . . . . .120 W per channel
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 W
Surround. . . . . . . . . . . . . . . . . .120 W per channel
Audio section
•
Input (Sensitivity/Impedance)
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . .335 mV/47 k
•
Frequency response
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . 5 Hz to 100 000 Hz
•
Output (Level/Impedance)
CD-R/TAPE/MD, DVR/VCR . . . . . . 335 mV/2.2 k
•
Tone control
Bass . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz)
Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)
•
Signal-to-Noise Ratio (IHF, short circuited,
A network)
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . . . . . . . . .96 dB
•
Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . . . . . . . . 79 dB
Ω
)
Ω
dB
Ω
(at volume level –50 dB)
1
Comments to this Manuals
Latest comments: