Extron electronics System 5 IP Series Setup Manual page 9

im Vertrieb von
System 5 IP Hardware Setup
This chapter describes rear and front panel features and basic
front panel operation of the System 5 IP switcher. It shows
you how to connect the cables to audio, video, and control
connectors.
Rear Panels and Cablng
100-240V 1.3A
R/VID G/Y B/C H V
Y C
R/VID G/Y B/C H V
50-60Hz
1
A/V nput and vdeo output connectons
a
Inputs 1 and 2: RGBHV/S-video/composite video inputs
— Connect cables from an RGBHV, S-video (Y/C), or composite
video source to each of these inputs. See the diagrams below.
Inputs must be configured for either video or RGB. See chapters
three, four, and five in the System 5 IP Series User's Manual for
details.
RGBHV
R/VID G/Y B/C H
Y C
S-video
R/VID G/Y B/C H
b
Inputs 3 and 4: S-video/composite video inputs — Connect
the cable from either an S-video (Y/C) source (using the 4-pin
mini DIN connector) or a composite video source (using the
BNC connector) to each of these inputs. Inputs 3 and 4 are not
configurable.
c
Display outputs — Cable these output BNC connectors to
an RGBHV, S-video (Y/C), or composite video port on the
projector or display. See the diagram below.
R
G
B
H
V VID
RGBHV Composite
Video
www.camboard.de
2-2 System 5 IP Switchers • Hardware Setup
VID PROJ CONT IR/SERIAL OUT
VID R
G
B Y
RS-232 A B C D
Tx Rx G Ps G +V S G S G S G S G
L 1 R L 2 R L 3 R
Y/C H V C
Y/C VID
2 3 4
V
Composite Video
V R/VID G/Y B/C H
Y
Y = luma
C = chroma
C
S-video
CAMBOARD Electronics
CM/IR/SCP
A B C D E
+V CM IR SCP
G
L 4 R
V
Tel. 07131 911201
Fax 07131 911203
d
Audio inputs — These inputs correspond to the like-numbered
video inputs. For each input, connect the cable from a balanced
or unbalanced stereo or mono audio input source. See the
wiring diagrams below.
N Do not tin the stripped leads before installing them in the
captive screw connector. Tinned wires are not as secure in
the captive screw connectors and could pull out.
CAUTION
For unbalanced audio, connect the sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the negative (-) contacts.
Tip
Ring
Sleeve
Sleeve (s)
Tip
Sleeve Ring
Unbalanced Stereo Input
(high impedance)
N
After the audio inputs and outputs are connected, refer to
chapter 3, "Front Panel Features and Basic Operation"
and chapter 4, "Software- and Web Page-based Setup and
Control" from the System 5 IP Series User's Manual.
Audo output connectons
LAN
CONFIG/RS-232
RELAYS
B
A C
_
C 3 4 C 5 6
C 1 2
RIGHT
L LINEOUT R L PREAMP R
1
a
Lineout and preamp audio outputs — Connect an audio output
device to either connector for line level audio outputs. The
lineout and preamp audio outputs are simultaneously active.
Therefore, two devices can be connected at the same time (one to
each output).
• The lineout connector outputs a fixed level audio signal
that is not affected by audio adjustments.
• The preamp connector outputs a variable, line level audio
signal for use with a powered amplifier. The volume can
be controlled (attenuated) via the front panel knob, RS-232,
or Ethernet/IP communication. The volume range is 0
(mute) through 40 steps (0% through 100% of the maximum
volume).
ce-info@camboard.de
System 5 IP Switchers • Hardware Setup
3/16" (5 mm) MAX.
Tip
Tip
Balanced Stereo Input
(high impedance)
R
_
LEFT
2 (Amplifier
Models Only)
2-3