DeWalt DCN692 Original Instructions Manual page 59

FUEL GAUGE BATTERY PACKS (FIG. 2, 2A)
Some D WALT battery packs include a fuel gauge
E
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (p). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
NOTICE: Do not store tool with battery
pack installed. To prevent damage to
the pack and to ensure best battery life,
store battery packs out of the tool or
charger in a cool, dry location.
Rotating Rafter/Belt Hook (fi g. 6)
The rafter/belt hook (j) and can be easily positioned
to the left or right of the tool to accommodate left-
or right-handed users.
If use of the hook is not desired at all, it can be
rotated to the front or back of the handle base.
Loading the Tool (fi g. 4)
WARNING: Always lock tool off and
disconnect battery pack before loading
and unloading fasteners.
1. Slide the spring-loaded pusher latch (h) to the
base of the magazine to lock it into place.
2. Select an appropriate collated nail stick. (Refer
to Technical Data.) D
WALT would always
E
recommend that you use D
fix nails.
WARNING: Since accessories, other
than those offered by D
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only D WALT recommended
E
accessories should be used with this
product.
3. Insert collated nail stick into the loading slot on
side of the magazine. Be sure the fasteners ride
on their heads in the nail channel.
4. Close the magazine by releasing the pusher
latch. Carefully allow the latch to slide forward
and engage the nail strip.
Dry Fire Lock out
The nailer is equipped with a dry fire lock out
which restricts the tool from actuating when the
magazine is nearly empty. When approximately 7 to
9 nails remain in the magazine, the tool dry fire lock
actuates. Refer to Loading the Tool to reload a
stick of collated nails.
NOTE: If heavy force is placed on the tool it is
possible to override the lock out. This protects the
tool from potential damage if dropped.
Adjusting the Driving Depth (fi g. 5)
The nail driving depth can be adjusted using the
depth adjustment wheel.
1. To drive the nail shallower, rotate the depth
adjustment wheel (d) to the left, toward the
shallow nail icon.
2. To sink a nail deeper, rotate the depth
adjustment wheel (d) to the right, toward the
deeper nail icon.
Selecting the Mode (fi g. 1)
DCN692
To select sequential action mode, slide the mode
selector switch (i) to display the single nail icon (
To select bump action mode, slide the mode
selector switch (i) to display the three nail icon (
NOTE: Maximum power for driving long nails is
achieved in sequential mode, so limit use of bump
mode when driving longer nails.
DCN695
To select standard sequential mode, slide the mode
selector switch (i) to display the single arrow ( ) icon.
To select RapidCycle
the mode selector switch (i) to display the double
arrow ( ) icon.
WALT branded first
E
NOTE: Battery life in RapidCycle
will be shorter than in standard sequential mode.
Leaving the tool in standard sequential will give
WALT, have
E
maximum battery life.
Speed Selection (fi g. 1)
This nailer is equipped with a dual speed selection
switch (n) located on the foot.
• For shorter nails, select speed 1 by setting the
switch to the left most position.
ENGLISH
TM
sequential action mode, slide
TM
sequential mode
).
).
57