DeWalt DCN690 Instruction Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Nail Gun
  5. DCN690
  6. Instruction manual

DeWalt DCN690 Instruction Manual

20v max cordless framing nailer
Hide thumbs Also See for DCN690:
Table of Contents

Advertisement

Quick Links

Download this manual
Before returning this product call
1-800-4-D
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DCN690, DCN692
20V Max* Cordless Framing Nailer
Cloueur pour charpente sans fil 20V max*
Clavadora inalámbrica de 20 V max*
WALT
E
Questions? Visit www.D
IF YOU SHOULD EXPERIENCE A PROBLEM WITH YOUR D
PURCHASE,
CALL 1-800-4 D
IN MOST CASES, A D
WALT REPRESENTATIVE CAN RESOLVE
E
YOUR PROBLEM OVER THE PHONE.
IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL.
YOUR FEEDBACK IS VITAL TO THE SUCCESS OF D
QUALITY IMPROVEMENT PROGRAM.
WALT.com
E
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
WALT
E
WALT
E
WALT'S
E

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCN690

Summary of Contents for DeWalt DCN690

  • Page 1 INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO GUIDE D’UTILISATION ANTES DE USAR EL PRODUCTO. MANUAL DE INSTRUCCIONES DCN690, DCN692 20V Max* Cordless Framing Nailer Cloueur pour charpente sans fil 20V max* Clavadora inalámbrica de 20 V max*...

  • Page 2: Defi Nitions: Safety Guidelines

    FIG. 1 Defi nitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

  • Page 3: General Power Tool Safety Warnings

    IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D WALT TOOL, CALL US f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and TOLL FREE AT: 1-800-4-D WALT (1-800-433-9258). gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
  • Page 4 • Use caution while removing a jammed Do not tape or tie trigger in the ON position. causing the nail to ricochet, injuring you FIG. A FIG. H fastener. The mechanism may be under Do not remove spring from contact trip. or a co-worker.

  • Page 5: Important Safety Instructions For All Battery Packs

    TO AVOID DOUBLE FIRES: Important Safety Instructions for All Battery Packs • Do not engage the tool against the work surface with a strong force. When ordering replacement battery packs, be sure to include the catalog number and voltage. • Allow the tool to recoil fully after each actuation. Consult the chart at the end of this manual for compatibility of chargers and battery packs.

  • Page 6: Important Safety Instructions For All Battery Chargers

    The RBRC™ Seal Minimum Gauge for Cord Sets The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel Volts Total Length of Cord in Feet (meters) cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate Ampere Rating 120V 25 (7.6) 50 (15.2)

  • Page 7: Operation

    This indicates the INTENDED USE power source is out of limits. The DCN690 cordless framing nailer has been designed for driving nails into wooden workpieces. Important Charging Notes DO NOT use under wet conditions or in presence of flammable liquids or gases.

  • Page 8: Mode Selection

    Installing and Removing the Battery Pack (Fig. 3) NOTICE: The contact trip needs to be depressed followed by a trigger pull for each nail followed by a release of both the contact trip and trigger after each nail. NOTE: For best results, make sure your battery FIG.
  • Page 9 Preparing the Tool 2. Tip the tool up until the fastener strip slides freely out of the magazine. 3. With battery removed, check the nosepiece to verify there are no nails remaining. NOTICE: NEVER spray or in any other way apply lubricants or cleaning solvents NOTE: The tool is equipped with a magnet in the nose area for improved tool performance.

  • Page 10: Maintenance

    Stall Release (Fig. 12) Rotating Rafter Hook (Fig. 14) FIG. 12 If the nailer is used in harder wood where all available energy in the motor WARNING: Never use hook to hang tool from belt or other clothing unless tool is in sequntial is used to drive a fastener, the tool may stall.
  • Page 11 Accessories FIG. 17 FIG. 18 FIG. 19 WARNING: Since accessories, other than those offered by D WALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only D WALT, recommended accessories should be used with this product.

  • Page 12: Register Online

    To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a D WALT factory service center, a D WALT authorized service center or other qualified service personnel. Always use identical replacement parts. Refer to the Troubleshooting Guide at the end of this section.

  • Page 13: Troubleshooting Guide

    TROUBLESHOOTING GUIDE MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A D WALT SERVICE CENTER OR CALL 1-(800)-4-D WALT. WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, ALWAYS BEFORE ALL REPAIRS DISCONNECT BATTERY PACK FROM TOOL SYMPTOM...
  • Page 14 El tiempo de duración de carga es aproximado; la duración de carga real puede variar. Lea el manual de instrucciones para obtener información más precisa. WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (NOV13) Part No. N329480 DCN690, DCN692 Copyright © 2012, 2013 D WALT The following are trademarks for one or more D WALT power tools: the yellow and black color scheme;...

This manual is also suitable for:

Dcn692Dcn692b

Table of Contents