Daikin F-Series Service Manual page 227

Instruction
• Make sure that a separate power supply cir-
cuit is provided for this air conditioner and
that all electrical work is carried out by quali-
fied personnel according to local laws and
regulations.
Pay attention to running noises, too
• Are the following places selected?
a.A place that can sufficiently withstand the
weight of the air conditioner with less running
noises and vibrations.
b.A place where the hot wind discharged from the
air outlet of the outdoor unit and the running
noises.
• Are you sure that there are no obstacles near
the air outlet of the outdoor unit?
Such obstacles may result in declined perfor-
mance and increased running noises.
• If abnormal noises occur in use, stop the oper-
ation of the air conditioner, and then consult
your dealer or our service station.
Regarding drainage of drain piping
• Is the drain piping executed to perform com-
plete drainage?
If proper drainage is not carried out from the out-
door drain pipes during air-conditioning operation,
chances are that dust and dirt are clogged in the
pipe. This may result in a water leakage from the
indoor unit. Under such circumstances, stop the
operation of the air conditioner, and then consult
your dealer or our service station.
5. NAME AND FUNCTION OF EACH
SWITCH AND DISPLAY ON THE
REMOTE CONTROLLER
Refer to figure 1 on page [1]
ON/OFF BUTTON
Press the button and the system will start.
1
Press the button again and the system will
stop.
OPERATION LAMP (RED)
2
The lamp lights up during operation.
DISPLAY "
IZED CONTROL)
3
When this display shows, the system is
UNDER CENTRALIZED CONTROL.
DISPLAY "
(VENTILATION/AIR CLEANING)
4
This display shows that the total heat
exchange and the air cleaning unit are in
operation (These are optional accessories).
216
" (UNDER CENTRAL-
" " " " " " "
DISPLAY " " " " "
(OPERATION MODE)
5
This display shows the current OPERATION
MODE. For cooling only type, "
and " " (Heating) are not installed.
DISPLAY " " (INSPECTION/TEST
TEST
OPERATION)
6
When the INSPECTION/TEST OPERATION
BUTTON is pressed, the display shows the
system mode is in.
hr
DISPLAY " " (PROGRAMMED TIME)
hr
7
This display shows the PROGRAMMED
TIME of the system start or stop.
DISPLAY " " (SET TEMPERATURE)
C
8
This display shows the set temperature.
DISPLAY " " (FAN SPEED)
9
This display shows the set fan speed.
DISPLAY " " (AIR FLOW FLAP)
10
Refer to "AIR FLOW DIRECTION ADJUST".
DISPLAY " " (TIME TO CLEAN AIR FIL-
TER)
11
Refer to "HOW TO CLEAN THE AIR FILTER".
DISPLAY " " (DEFROST)
12
Refer to "DEFROST OPERATION".
NON-FUNCTIONING DISPLAY
If that particular function is not available,
pressing the button may display the words
"NOT AVAILABLE" for a few seconds.
13
When running multiple units simultaneously
The "NOT AVAILABLE" message will only be
appear if none of the indoor units is equipped
with the function. If even one unit is equipped
with the function, the display will not appear.
TIMER MODE START/STOP BUTTON
14
Refer to "PROGRAM TIMER OPERATION".
TIMER ON/OFF BUTTON
15
Refer to "PROGRAM TIMER OPERATION".
INSPECTION/TEST OPERATION BUTTON
16
This button is used only by qualified service
persons for maintenance purposes.
PROGRAMMING TIME BUTTON
17
Use this button for programming "START and/
or STOP" time.
TEMPERATURE SETTING BUTTON
18
Use this button for SETTING TEMPERA-
TURE.
FILTER SIGN RESET BUTTON
19
Refer to HOW TO CLEAN THE AIR FILTER.
SiBE12-713
" " " " "
" (Auto)
Operation Manual