Lexmark MS810 User Manual page 358

Index
printer
configurations 41, 83, 130
finishing features 185
minimum clearances 10, 11
models 41, 83, 130
moving 10, 11, 262
selecting a location 10, 11
shipping 262
printer control panel
adjusting brightness 247
factory defaults,
restoring 78, 124, 173
indicator light 44, 86, 133
parts 43, 85, 132
Sleep button light 44, 86, 133
using 43, 85, 132
printer control panel, virtual
display
using the Embedded Web
Server 120
Printer had to restart. Last job
may be incomplete. 292
printer hard disk
disposing of 78, 125, 174
encrypting 81, 128, 176
installing 23
removing 27
wiping 80, 127, 176
printer hard disk
encryption 81, 128, 176
printer hard disk memory
erasing 80, 127, 176
printer information
where to find 8
printer IP address
finding 89, 137
printer is printing blank
pages 327
printer messages
Cartridge, imaging unit
mismatch [41.xy] 282
Change [paper source] to
[custom string] load
[orientation] 282
Change [paper source] to
[custom type name] load
[orientation] 282
Change [paper source] to
[paper size] load
[orientation] 282
Change [paper source] to
[paper type] [paper size] load
[orientation] 282
Check tray [x] connection 283
Close door or insert
cartridge 283
Close finisher rear door 283
Close rear door 283
Complex page, some data may
not have printed [39] 283
Configuration change, some
held jobs were not restored
[57] 284
Defective flash detected
[51] 284
Disk full [62] 284
Disk must be formatted for use
in this device 284
Disk near full. Securely clearing
disk space. 284
Empty the hole punch box 285
Error reading USB drive.
Remove USB. 285
Error reading USB hub. Remove
hub. 285
Imaging unit low [84.xy] 285
Imaging unit nearly low
[84.xy] 285
Imaging unit very low, [x]
estimated pages remain
[84.xy] 285
Incompatible output bin [x]
[59] 285
Incompatible tray [x] [59] 286
Incorrect paper size, open
[paper source] [34] 286
Insert hole punch box 286
Insert staple cartridge 286
Insert Tray [x] 286
Install bin [x] 287
Install Tray [x] 287
Insufficient memory for Flash
Memory Defragment operation
[37] 287
Insufficient memory to collate
job [37] 288
Insufficient memory to support
Resource Save feature
[35] 288
Insufficient memory, some Held
Jobs were deleted [37] 287
Insufficient memory, some held
jobs will not be restored
[37] 288
Load [paper source] with
[custom string] [paper
orientation] 288
Load [paper source] with
[custom type name] [paper
orientation] 288
Load [paper source] with [paper
size] [paper orientation] 289
Load [paper source] with [paper
type] [paper size] [paper
orientation] 289
Load multipurpose feeder with
[custom type name]
[orientation] 289
Load multipurpose feeder with
[paper size] [orientation] 290
Load multipurpose feeder with
[paper type] [paper size]
[orientation] 290
Load multipurpose feeder with
custom string]
[orientation] 289
Load staples 290
Maintenance kit low
[80.xy] 290
Maintenance kit nearly low
[80.xy] 290
Maintenance kit very low
[80.xy] 291
Memory full [38] 291
Misfeed cleared, extra sheets in
output bin [24y.xx] 291
Network [x] software error
[54] 291
Non‑Lexmark [supply type], see
User's Guide [33.xy] 291
Not enough free space in flash
memory for resources
[52] 292
Paper changes needed 292
Parallel port [x] disabled
[56] 292
Printer had to restart. Last job
may be incomplete. 292
Reattach bin [x] 293
Reattach bins [x] – [y] 293
Reinstall missing or
unresponsive cartridge
[31.xy] 294
358