EXCELL PRECISION CO., LTD. Table of Contents INSTRUCTIONS FOR USE ....................2 PREPARING TO USE THE SCALE .................. 2 CHAPTER 1 INTRODUCTION ..................4 1-1 P ..................4 RODUCTION NTRODUCTION 1-2 D ....................5 ISPLAY ESCRIPTION 1-3 K ................6...
EXCELL PRECISION CO., LTD. Thank for your purchasing of our EXCELL Weighing Scale. To guide you to use our product correctly, please read this User Manual carefully to extend the life of machine and to avoid error. Instructions for Use 1.
EXCELL PRECISION CO., LTD. Due to the storage battery adopt the advanced free-maintaining technique, customers need not to replenish electrolyte. The scale should be recharged every 3 months to prevent failure of the internal rechargeable battery. 1. The battery should be charged for 8~10 hours.
EXCELL PRECISION CO., LTD. Chapter 1 Introduction 1-1 Production Introduction 1. High performance A/D converter 0.3 uv/D high sensitivity zero point adjustable range -2mV~ +5mV • • Sampling speed 15 times/second use range -4mV ~ +30mV • • load cell stimulate power source 5V DC ±2% 100mA non-linear scale 0.01% full scale...
EXCELL PRECISION CO., LTD. 1-2 Display Description High limit value OK value (The value between HI and LO limit value) Low limit value “Zero” indication →O← “Net weight” indication “Low battery power” indication ▼1 “Stable” indication ▼2 “Pre-tare mode” indication ▼3...
EXCELL PRECISION CO., LTD. 1-3 Keypad Functions Description 10-key model has not key and key. Press this key to select the required unit from the preset units. Press this key to preset the weight and quantity. Press this key to accumulate the weight value or others.
EXCELL PRECISION CO., LTD. Low Power Alarm Please note when the ( ) symbol keeps flashing on the left down corner of the display, the batteries should be recharged. The scale will turn off automatically after a few hours when the low battery warning symbol shows up.
EXCELL PRECISION CO., LTD. Chapter 2 General Operation Description 2-1 Backlight Function Press key to select the display backlight mode: ⇒ “Auto Backlight” mode. When the weight is over 10d or any key is pressed, the display backlight will be switched on. When the weight returns to zero (the weight on platform is less than 10d), the display backlight will switch off after 10 seconds.
Page 11
EXCELL PRECISION CO., LTD. Preset “Beeper value” ( Refer to Note ) e.g. Beeper value = 22 Press key 1 time the display shows Press key 2 times the display shows Press key 1 time the display shows Press key 2 times...
EXCELL PRECISION CO., LTD. ♦ When changing between weighing and counting mode, or selecting weighing unit, the indicator will automatically clear all the totalized weight values. ♦ The indicators will automatically clear all the totalized weight values after turning 3. Recall Totalized Weight Values...
EXCELL PRECISION CO., LTD. the procedures, the net indication and pretare indication “ ” is on. Place goods into the container, then the indicator shows the net weight of goods. Clear pretare value Press then key, and then press key to clear pretare value.
EXCELL PRECISION CO., LTD. Chapter 3 General Function Setting ♦ Switch on the scale. While the scale is counting down to zero, press and hold until the display shows the software program version number Release the key, the scale enters into the configuration setting mode and is showed on the display.
EXCELL PRECISION CO., LTD. ⇒ Check Weighing Configurations ♦ If hold mode is set, accessing to is denied. key to select F4 function ⇒ the display shows Press Press key for 5 times to clear HI, OK, LO values Preset “LO value”...
EXCELL PRECISION CO., LTD. ⇒ RS-232 Interface Output Setting (option) key to select F5 function ⇒ the display shows key = Increase the flash value by one (from 0 to 10) or selecting baud rate from 1200, 2400,4800 and 9600(default setting).
Page 18
EXCELL PRECISION CO., LTD. RS-232 Interface Format I . Mode: UART Signal of EIA-RS0232 C II . Format : 1. Baud rate : 1 200, 2 400, 4 800, 9 600 bits/second 2. Data bits : 8 bits 3. Parity bit : None 4.
Page 19
EXCELL PRECISION CO., LTD. HEAD1 ( 2 BYTES ) HEAD2 ( 2 BYTES ) OL - Overload , Under load TR - TARE Mode ST - Display is Stable NT - NET Mode US - Display is Unstable GS -...
Page 21
EXCELL PRECISION CO., LTD. Stable Transmission (totalizing mode) WT/UNIT ( kg / lb ) - - - - - - - - - - - - - - 0001 1.0000 The scale is stable 0002 1.0000 The scale is stable 0003 1.0000...
Page 22
EXCELL PRECISION CO., LTD. Then the printing form is: FR”WT3N ” 1,200 0,700 0,300 0,200 000020001000000020 P1,1 key or key twice to clear the format Then, form of clearing the printing: “ “ <LF> ? <LF> TN TN TN <LF>...
EXCELL PRECISION CO., LTD. ⇒ Exit Function Setting Mode key to select F6 function ⇒ the display shows Press Counting down to zero and exit setting mode ⇒ Internal Value Display Mode key to select F7 function ⇒ the display shows...
EXCELL PRECISION CO., LTD. ⇒ G value Calibration key to select F10 function. ⇒ The display shows key or You can input at most 9 sets of G value’s data. The historic data can be found out and not to be revised.
EXCELL PRECISION CO., LTD. ⇒ ID Code Setting , , (Use must be in coordination with key to select F11 function ⇒ the display shows key or Press Machine ID code setting: Press to set 01 ~ 99 Default setting: 00 (1) “00”: RS-232 does not transmit Machine ID...
EXCELL PRECISION CO., LTD. ⇒ Print Key ( ) Function Setting key to select F12 function ⇒ the display shows key or Press to set 0 ~ 2 Default setting: 0 Press ⇒ Press key to print current weight if weight variation is within ±1d ~ ±10d, or to print accumulated weight if weight variation is over...
EXCELL PRECISION CO., LTD. ⇒ Printing orders when is set as No.0 No print. No.1 TICKET NO. No.2 No.3 No.4 No.5 No.6 No.7 No.8 No print No.9 No print Contains a 9-digit code is set as The format of is as following...
Page 28
EXCELL PRECISION CO., LTD. is set as The format of is as following P/N 012345678901 TICKET NO. 0001 75.01kg 0.00kg 0.00kg 75.01kg WT/UNIT ( kg / lb ) - - - - - - - - - - - - - - 0001 1.0000...