Water Purification System Programming; Spa Maintenance - Jacuzzi J-210 Installation Manual And User's Manual

F4: 4 hours of skimming/heating per day
(one 2-hour cycle every twelve hours)
F5: 6 hours of skimming/heating per day
(one 2-hour cycle every eight hours)
F6: 8 hours of skimming/heating per day
(one 2-hour cycle every six hours)
I Lock mode (L1-L3)
(In this mode, the display will flash alternately indicating the tem-
perature and the lock mode number).
L1: Full lock out (de-activates all hot tub functions)
NOTE: The spa should not be left in this lock mode for an ex-
tended period of time. Especially in colder climates or when freez-
ing conditions exist.
L2: Partial lock out
(disables the buttons for jets and light to prevent unau-
thorized use of the spa). In this mode, the skim-
ming/heating mode continues to operate as programmed.
When this function has been activated, the temperature
display
L3: Disables the "+" and "-" buttons to prevent temperature adjust-
ments. The filtering/heating cycle will continue to function as
programmed. Jet and lights buttons will continue to function
normally while the temperature value blinks.
NOTE: To exit a Lock Mode you will need to re-enter the filtra-
tion/heating modes and select a cycle from F1-F6.

Water purification system programming

Programming the CLEARRAY System (U) or Corona Dis-
charge Ozone (O3) (where included)
Press and hold the Jets pump 1 (
at the same time for 3 seconds; The screen will display one of
the two menus below:
Press
Press
or
or
If a "U" is displayed on the LED screen, by pressing the Pump
1 button the sanitising system will switch from "U" to "O3", af-
ter which you will exit the programming menu.
If an "O3 is displayed on the LED screen, by pressing the Pump
1 button the sanitising system will switch from "O3" to "U", af-
ter which you will exit the programming menu.
) and Cooler ( ) button
1
Press
Press
or
or
Note: For the O3 option the "=" symbol disables the duration
countdown timer.
If you do not wish to change the option do not press any but-
tons and after 10 seconds the display will return to the main
menu.
Note: If the CLEARRAY system has been selected, once the indi-
cated time has ran out (365 days), the display will Flash alter-
nately indicating the water temperature and the "blb" message.
This means that the UV bulb needs to be replaced.
Resetting the duration countdown timer (CLEARRAY™ Sys-
tem only)
When the timer reaches zero, it must be reset, after replacing
the UV bulb.Proceed as follows to reset the timer:
Press
Press
Press and hold Jets pump 1 (
time for 3 seconds.
Press the Warmer ( ) button until the display shows "0".
If the timer has reached "0", pressing the Jets pump 1 (
button will reset the timer to 365 days. If the timer is not at
"0" pressing the Jets pump 1 button will not reset it.
Note: An eventual power failure of the hot tub will not affect the
operation of the timer. The number of remaining days is stored in
memory and the countdown resumes when the power is restored.
If the timer is not on "0" and you need to reset the value, pro-
ceed as follows:
A. Press and hold the Jets pump 1 and Cooler buttons at the
same time for 3 seconds.
B. Press the Warmer button to scroll to "U".
C. Press the Jets pump 1 button to switch from "U" to "O3".
D. Press and hold the Jets pump 1 and Cooler buttons at the
same time for 3 seconds.
E. Press the Warmer button to scroll to "O3".
F. Press the Jets pump 1 button to switch from "O3" to "U". The
timer has been reset to 365 days.

Spa maintenance

Proper and regular maintenance of your spa will help it retain its
beauty and performance.
Information regarding spa cleaning and maintenance and
the products to be used can be found in the catalogue-
guide provided with the product.
I Cleaning the filter
(models J-210-J-215-J-225-J-235-J-245-J-275)
These models are equipped with a basket and a filter car-
tridge, located in the compartment housed on the inside wall
of the hot tub.
31
Press
Press
1
) and Cooler ( ) at the same
1
)
1