Siemens Milltronics BW500 Operating Instructions Manual page 215

O
Online Calibration, 85
Options, 19
Output, 18, 101
P
P388 and enter EDIT mode, 79
P392 linearizer compensation %, 172
P771 (IP) network address, 128, 130, 131
P772 (IP) baud rate, 128
P774 (IP) data bits, 129
P775 (IP) stop bits, 129
P778 (IP) modem available, 129
P779 (G) modem inactivity timeout, 130
parameter, 172
P000 security lock, 153
P001 language, 153
P002 test reference selection, 153
P003 number of load cells, 154
P004 rate measurement system, 154
P005 design rate units, 154
P008 date, 154
P009 time, 155
P011 design rate, 155
P014 design speed, 155
P015 speed constant, 155
P016 belt length, 156
P017 test rate, 156
P019 manual span adjust, 157
P022 minimum speed frequency, 157
P080 damping display, 157
P081 display scroll mode, 158
P100 relay function, 158
P101 high alarm/deviation alarm, 159
P102 low alarm, 159
P107 relay alarms, 159
P118 relay logic, 160
P119 relay override, 160
P200 mA output range, 161
P201 mA output function, 161
P204 mA output average, 161
P212 mA output minimum, 162
P213 mA output maximum, 162
P214 mA output trim, 162
P215 20 mA output trim, 162
P220 mA output damping, 162
P250 mA input range, 163
P255 mA input function, 163
P261 mA input trim, 163
P262 mA input trim, 164
BW500 and BW500/L
Operating Instructions, 12/2016, A5E33482052-AD
P270 auxilliary input function, 165
P341 days of service, 167
P350 calibration security, 168
P355 online calibration feature, 168
P356 online calibration reference weight, 168
P357 online calibration limits, 169
P359 factoring, 169
P360 calibration duration, 169
P365 multispan, 170
P367 direct zero entry, 170
P370 zero limit deviation, 171
P370 zero limit deviation %, 171
P371 auto zero initiation upper limit, 171
P377 initial zero, 171
P388 initial span, 171
P390 linearizer, 172
P391 linearizer load points, 172
P398 moisture content, 172
P398-02 moisture content, 172
P399 incline sensing, 173
P400 PID system, 173
P401 PID update time, 173
P402 PID process value source, 174
P405 proportional terms, 174
P406 integral term, 174
P407 derivative term, 174
P408 feed forward term, 174
P410 manual mode output, 175
P414 setpoint configuration, 175
P415 local set point value, 175
P416 external setpoint, 176
P418 remote setpoint ratio, 176
P419 PID freeze option, 176
P560 batch mode control, 176
P564 batch setpoint, 177
P566 batch pre-warn, 177
P567 batch pre-warn setpoint, 177
P568 batch pre-act, 177
P569 manual batch pre-act amount, 178
P598 span adjust percentage, 178
P619 totaling dropout, 178
P620 display zero dropout, 178
P631 totalizer resolution, 179
P634 communication totalizer resolutions, 180
P635 verification totalizer, 180
P638 external totalizer resolution, 181
P643 external contact closure, 182
P647 totalizer display, 182
P648 totalizer reset, internal, 182
P690 speed constant entry, 183
P691 drive pulley diameter, 184
P692 pulses per sensor revolution, 184
Index
213