Table of Contents
Advertisement
Heat Controller
INSTALLATION INSTRUCTIONS
Wall Sleeve Brands:
4
4
7
6
4
13
9
10
Room Air Conditioner with R-410A
4
8
8
3
3
4
5
6
4
8
11
12
#9 White Westinghouse or Frigidaire
#9 White Westinghouse or Frigidaire
( 22 Deep)
- (22" Deep)
Remove existing rear grille as shown on Page
1.
1. Remove existing rear grille as shown on Page 6 of this
6 of this manual and replace with provided
manual and replace with provided louvered rear panel.
louvered rear panel. Install as shown here.
Install as shown here.
NOTE: You may need to drill holes in flange
NOTE: You may need to drill holes in flange of existing
of existing sleeve to match new rear grille.
sleeve to match new rear grille.
Because of the increased unit depth, first try
Because of the increased unit depth, first try dry
dry fitting using the method described below:
fitting using the method described below:
2. Place (2) 1
3. Gently slide unit in and check if amount extend-
ing from the sleeve is sufficient once the trim
2. Place (2) 1" x 1-1/2" x 14" seals against each side.
frame is attached.
3. Gently slide unit in and check if amount extending from
4. If position is Ok, remove unit and proceed to
the sleeve is sufficient once the trim frame is attached.
the next step. If not go to step 8.
4. If position is Ok, remove unit and proceed to the next
5. Attach (1)1
step. If not go to step 8.
right sides of the sleeve.
5. Attach (1) 1" x 1-1/2" x 15" long seal to the left and right
6. Cut (1) 1
x1
1
sides of the sleeve.
attach it vertically to the rear grill 4.5 from
6. Cut (1) 1" x 1-1/2" x 25" long seal to 14" long and attach
the left side ,repeat and attach 4 from the right
side.
it vertically to the rear grill 4.5 from the left side ,repeat
7. Attach(1) 1
and attach 4 from the right side.
the top of the sleeve.Remove the backing paper
7. Attach(1) 1" x 1-1/2" x 25" long seal in the center at the
and press into position.Proceed to step 14.
top of the sleeve. Remove the backing paper and press
Use these next steps if the unit requires extra
into position. Proceed to step 14. Use these next steps if
extension into the room.
the unit requires extra extension into the room.
8. Attach 1 x
x14 long seal over the solid
3
/
4
8. Attach 1" x 3/4" x 14" long seal over the solid vertical
vertical portion of the rear grille.
portion of the rear grille.
9. Attach (2) 4
3
/
4
slot overlapping the seal above.
9. Attach (2) 4-3/4" x 3-3/4" x 1-3/4" foam blocks with the
10. Install the divider into the slots of the foam
slot overlapping the seal above.
blocks. You may need to trim the length to size.
10. Install the divider into the slots of the foam blocks. You
11. Repeat steps 8-10 for the other vertical shown
may need to trim the length to size.
portion of the grille as shown in the picture.
11. Repeat steps 8-10 for the other vertical shown
12. Attach (2) 1
portion of the grille as shown in the picture.
of the sleeve again making sure all seals are
12. Attach (2) 1" x 1-1/2" x 14" seals along the sides of the
flush.
sleeve again making sure all seals are flush.
13.Cut the 1
x1
13. Cut the 1" x 1-1/2" x 25" seal to fit the top of the sleeve.
sleeve. The pieces must be fitted flush to the
edge of the divider.
The pieces must be fitted flush to the edge of the divider.
14. Center unit and gently slide unit into sleeve.
14. Center unit and gently slide unit into sleeve.
15. Before sliding all-the-way back, remove 1st
15. Before sliding all-the-way back, remove 1st screw from
screw from front on left side of unit.
front on left side of unit.
16. Remove the plastic washer from the screw.
16. Remove the plastic washer from the screw.
17. Screw and attach the other end of the ground
17. Screw and attach the other end of the ground wire to
wire to the unit as shown in picture. Make sure
the unit as shown in picture. Make sure that the toothed
that the toothed washer is against the cabinet.
washer is against the cabinet.
18.Slide the unit completely to the rear to ensure
a good seal, making sure the ground wire does
18. Slide the unit completely to the rear to ensure a good
not become tangled.
seal, making sure the ground wire does not become
19.Seal & Frame the unit as described on page 17.
tangled.
20. If you have difficulty with mounting the grill to
19. Seal & Frame the unit as described on page 17.
the sleeve, follow the instructions for direct
20. If you have difficulty with mounting the grill to the sleeve,
mounting on Page 16.
follow the instructions for direct mounting on Page 16.
16
15
x1
1
/
x14 seals against each side.
2
x1
/
x15 long seal to the left and
1
2
x25 long seal to 14 long and
/
2
x1
x25 long seal in the center at
1
/
2
x3
x1 foam blocks with the
3
/
3
/
4
4
x1
x14 seals along the sides
1
/
2
x25 seal to fit the top of the
1
/
2
Owner's Manual
Hide quick links:
Advertisement
Table of Contents
