Heat Controller BG-103M Owner's Manual page 10

Owner's Manual
INSTALLATION INSTRUCTIONS
Wall Sleeve Brands:
4
8
3
4
5
Room Air Conditioner with R-410A
4
8
3
4
#2 Fedders - 19-3/4" Deep
#2 Fedders
1. Remove existing rear grille as shown on Page 6 of
this manual and replace with provided louvered rear
Remove existing rear grille as shown on Page
1.
panel. Install as shown here. 6 of this manual and replace with provided
louvered rear panel. Install as shown here.
NOTE: you may need to drill holes in flange of
NOTE: You may need to drill holes in flange
existing sleeve to match new rear grille.
of existing sleeve to match new rear grille.
2. Attach(2) 4-1/2" x 3-1/2" x 1-1/2" centering/support
blocks one on each side wall. Place in center of side
wall with the tapered end facing the opening.
/ / /
2. Attach(2)4 x3 x1 1
1
2
2 2
3. Cut (2) 17" Tapered Spacer Blocks as shown
one on each side wall. Place in center of side
below into two pieces.
wall with the tapered end facing the opening.
3. Cut (2) 17 Tapered Spacer Blocks as shown
below into two pieces.
3 /
Tapered Spacer Block
4
Cut Here
4. The 4" section is placed in front of the rib on
4. The 4 section is placed in front of the rib on
base with the tapered end facing the back of the
base with the tapered end facing the back of
sleeve. The remaining portion will be placed behind
the sleeve. The remaining portion will be
the rib again sloping toward the rear of the sleeve.
placed behind the rib again sloping toward
This helps induce a rearward slope on the unit.
the rear of the sleeve. This helps induce a
rearward slope on the unit.
5. Attach (1) 1" x 3/8" x 25" long seal in the center at
5. Attach (1)1 x3/8 x25 long seal in the center
the top of the sleeve. Remove the backing paper
at the top of the sleeve. Remove the backing
and press into position.
paper and press into position.
6. Attach (2) 1" x 3/8" x 14" seals to the left and right
6. Attach (2) 1 x3/8 x14 seals to the left and
sides of the sleeve.
right sides of the sleeve.
7. Cut (2) 1" x 3/8" x 25" long seals to 14" long and
7. Cut (2) 1 x3/8 x25 long seals to 14 long
attach it to the vertical sections of the rear grille as
and attach it to the vertical sections of the rear
shown.
grille as shown.
8. Gently slide unit into sleeve.
8. Gently slide unit into sleeve.
9. Before sliding all-the-way back, remove 2nd screw
9. Before sliding all-the-way back, remove 2nd
from front on left side of unit.
screw from front on left side of unit.
10. Remove the plastic washer from the screw.
10. Remove the plastic washer from the screw.
11. Screw and attach the other end of the ground
11. Screw and attach the other end of the ground
wire to the unit as shown in picture. Make sure wire to the unit as shown in picture. Make sure
that the toothed washer is against the cabinet.
that the toothed washer is against the cabinet.
12.Slide the unit completely to the rear to ensure
12. Slide the unit completely to the rear to ensure a
a good seal, making sure the ground wire does
good seal, making sure the ground wire does not
not become tangled.
become tangled.
13.Seal & Frame the unit as described on page 17.
13. Seal & Frame the unit as described on page 17.
14. If you have difficulty with mounting the grill to
14. If you have difficulty with mounting the grill to the
the sleeve, follow the instructions for direct
sleeve, follow the instructions for direct mounting on
mounting on Page 16.
Page 16.
9
Heat Controller
19 3 4 / Deep
centering/support blocks
/ /
1
2 2
17
1
4
Protection Paper
Backing