Programming Commands; Recommended Programming Procedure - Honeywell VISTA-128BPT Programming Manual

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
P r o g r a m m i n g
P r o g r a m m i n g
• To enter program mode, enter installer code + [8] + [0] + [0] + [0]
• To set standard defaults, press ∗97
• To change to next page of program fields, press ∗94
• To return to previous set of fields, press ∗99
• To erase account and phone number field entries, press [∗] + field number + [∗]
• To assign zone descriptors, press #93 + follow menu prompts
• To add custom words, press #93 + follow menu prompts
• To enter Installer's Message, press #93 + follow menu prompts
• To exit program mode, enter ∗99 OR ∗98: ∗99 allows re-access to programming mode by installer code.
∗98 prevents re-access to programming mode by installer code.
Standard default (∗97) values are shown in brackets [ ], otherwise default = 0.
R e c o m m e n d e d
R e c o m m e n d e d
The following is a step-by-step procedure recommended for programming your VISTA-128BPT/VISTA-250BPT/VISTA-
128BPTSIA systems.
1. Set the keypads (and other peripheral devices)
to the appropriate addresses.
Set factory defaults by pressing ∗97.
2.
This will automatically enable keypad addresses
00-01, so be sure at least one keypad is set to one
of these addresses.
3. Program system-wide (global) data fields.
Using the programming form as a guide, enter
program mode and program all system-wide
programming fields. These options affect the
entire system, regardless of partitions. They
include control options, downloader and dialer
options, RF options, event logging options, etc.
Refer to the Program Field Index for a listing of the
program fields and their function.
NOTE: Field 2∗00 (number of partitions) must
be programmed before continuing.
4. Program partition-specific fields.
When the system-wide fields have been
programmed, program all partition-specific
programming fields by first pressing ∗91 to select
a partition (while still in data field program mode).
Then enter the first partition-specific field number
*09. When you are finished, the next partition-
specific field is automatically displayed. Partition-
specific fields can have different values for each
partition. To program the fields for the next
partition, press ∗91, enter the desired partition
number, and then enter field ∗09. Refer to the
MECHANICS OF PROGRAMMING section in the
VISTA-128BPT/VISTA-250BPT Installation and
Setup Guide for detailed instructions.
5. Use #93 Menu Mode for device programming.
Refer to Device Programming in this guide to
assign keypad ID numbers and default partitions
for each keypad, and to selectively suppress
certain keypad sounding options. Also use this
mode to assign RF receivers, relay modules, and
the ECP Communications Device.
S E
S E
C o m m a n d s
C o m m a n d s
P r o g r a m m i n g
P r o g r a m m i n g
C T I O N : 2
C T I O N : 2
P r o c e d u r e
P r o c e d u r e
6. Use #93 Menu Mode for zone programming.
Refer to Zone Programming in this guide to
program zone response types, assign right loop
zones and wireless zones, assign zones to
partitions, and to program alarm report codes.
7. Use #93 Menu Mode for programming outputs.
Refer to Output Programming in this guide to
program desired output operation.
8. Program Communication options.
Refer to System Communication section in
theVISTA-128BPT/VISTA-250BPT Installation and
Setup Guide for detailed instructions. Then use
#93 menu mode to program report codes.
9. Use #93 Menu Mode for programming alpha
descriptors.
Refer to Alpha Programming in this guide to enter
zone and partition descriptors and a custom
installer's message.
10. Use #93 Menu Mode for relay voice descriptors
and custom word substitutes.
Refer to Relay Voice Descriptors in this guide for
further instructions for programming relay
descriptors to be annunciated.
11. Use #80 Mode for programming schedules.
Refer to the Scheduling Menu Prompts in the
VISTA-128BPT/VISTA-250BPT Installation and
Setup Guide to program open/close schedules,
temporary and holiday schedules, limitation of
access schedules, and time-driven events.
3
P R O G R A M
P R O G R A M
M I N G
M I N G