System - Panasonic AJ-SD930BE Operating Instructions Manual

CONTENTS
Parts and their functions
Rear panel
1 2 3 4 5
AES/EBU ANALOG
CH1/2
VIDEO
IN
IN
AC IN
Y
CH3/4
IN
P B
CH1/2
REF VIDEO
OUT
IN
P R
CH3/4
OUT OPTION
Y 1 VIDEO
OUT
2
P B
(WFM)
3
P R
(SUPER)
SIGNAL
GND
SERVICE ONLY
1 AC IN socket
Connect one end of the power cord supplied to this
socket and the other end to the power outlet.
2 DIGITAL AUDIO IN and OUT connectors
These are the input and output connectors for
digital audio signals that comply with the AES/EBU
standards.
<Note>
The digital audio signals which are to be input to
these connectors must be synchronized with the
video input signals. Otherwise, noise will be
generated in the audio output signals.
3 ANALOG COMPONENT VIDEO IN connectors
(optional)
The analogue component video signals are input to
these connectors.
4 ANALOG COMPOSITE VIDEO IN connectors
and 75 Ω termination switch (optional)
The analogue composite video signals are input to
these connectors. A loop-through configuration is
featured for each pair of input connectors.
For termination at this VTR, set the termination
switch to ON.
5 REF VIDEO IN connectors and 75 Ω termination
switch
These are the input connectors of the reference
video signals.
Input a reference signal with colour burst.
For termination at this VTR, set the termination
switch to ON.
<Note>
Video and audio output may be disturbed when the
reference video signal is not input, so it is
recommended that a system which inputs the
reference video signal be used.
14 (E)
6 7 8 9 : ;
REMOTE ANALOG
SDI
IN OUT
REMOTE IN/OUT PUSH PUSH PUSH TC
CH1 AUDIO CH2
ON IN
IN
75Ω
1
OFF
REMOTE OUT
ACTIVE
PUSH PUSH TC
CH3 CH4 THROUGH
OUT
2
ENCODER REMOTE
ON
75Ω
3
OFF (SUPER)
CH1 AUDIO CH2 MON
RS-232C OUT L
OPTION
SDTI
IN OUT
PARALLEL
CH3 MON
CH4
1
R
2
6 Remote control connectors
These connectors make it possible to use two of
these VTRs or to connect this VTR to an external
controller so that the VTR can be operated from an
external component.
Two remote control connectors are provided: one
for IN/OUT use and the other for OUT use only.
IN/OUT:
For connection with an external controller
For connection with deck-to-deck operations
OUT:
For connection with parallel run operations
For loop-through use
<Note>
If connection is to be made to the OUT connector
for deck-to-deck operations where this VTR will
serve as the recorder, which of the two connectors
is to be used can be selected using setup menu No.
212 (MASTER PORT).
7 ENCODER REMOTE connector
An external encoder remote controller is connected
to this connector when the video output signal
settings are to be adjusted from an external
component.
8 ANALOG AUDIO IN connectors
These are the analogue audio input connectors.
9 TIME CODE IN connector
This connector is used to record an external time
code onto the tape.
: TIME CODE OUT connector
During playback, the playback time code is output
through this connector.
During recording, the time code generated by the
internal time code generator is output.
; SERIAL DIGITAL COMPONENT AUDIO and
VIDEO IN and OUT connectors
These are the input and output connectors for the
digital component audio and video signals that
comply with the ITU-R BT.656-4 standard.
Video signals containing superimposed information
can be output through the SDI OUT 3 connector.
Whether the superimposing is to be set ON or OFF
is selected using the SUPER switch W on the front
panel.
<Note>
The digital audio signals which are to be input to
these connectors must be synchronized with the
video input signals. Otherwise, noise will be
generated in the audio output signals.