Falcon Automated System; Description And Technical Specifications; Dimensions; Maximum Use Curve - Genius falcon m User Manual

These instructions apply to the following models:
FALCON 14 M - FALCON 14 MC - FALCON 20 M- FALCON 20 MC - FALCON
15 M - FALCON 15 MC - FALCON 20 M 3PH
The FALCON gearmotor for sliding gates is an electro-mechanical opera-
tor which transmits drive to the sliding leaf by a rack and pinion or by a
chain suitably coupled to the gate.
The non-reversing system guarantees mechanical locking of the gate
when the motor is not operating and, therefore, there is no need to install
any lock.
The gearmotor does not have a mechanical clutch and, therefore,
requires a control unit with an adjustable electronic clutch which
guarantees the necessary anti-crushing safety.
A handy manual release with a customised key makes the gate manoeu-
vrable in case of a power cut or trouble.
In the "C" version gearmotors, the electronic control unit is housed inside
the operator.
The FALCON gearmotor was designed and built for controlling
vehicle access. Do not use in any different way.

1. DESCRIPTION AND TECHNICAL SPECIFICATIONS

 Foundation plate
 Gearmotor
 Enclosure and control unit
(In "C" versions only)
 Magnetic sensor
 Pinion
 Release knob with key
 Securing slots and nuts
 Lateral protective devices
 Covering housing
MODEL
Power supply (+6% -10%)
Absorbed power (W)
Absorbed current (A)
Electric motor (rpm)
Thrust capacitor (µF)
Thrust on pinion (daN)
Torque (Nm)
Temperature protection (°C)
Max leaf weight (Kg)
Type of pinion gear
Gate speed (m/min)
Max. gate length (m)
Type of travel-limit device
Type of clutch
Use frequency (see graph)
Operating ambient temperature (°C)
Weight of gearmotor (Kg)
Protection class
Operator dimensions

FALCON AUTOMATED SYSTEM

Fig. 1
14 M 20 M 15 M 20 M
14 MC 20 MC 15 MC 3Ph
230 V~ 115 V~ 400 V~
50 Hz 60 Hz 50Hz
650 800 710 840
2.8 3.5 6.7 2.2
1400 1700 1400
16 20 60 /
110 150 130 185
35 45 38 60
140 /
1400 2000 1500 2000
Z 16 module 4
10 11 10
20
Magnetic
Electronic torque control
(See control unit)
S3
S3 - 40%
50%
-20 ÷ +55
14 15
IP 44
See fig. 2

2. DIMENSIONS

3. MAXIMUM USE CURVE

The curve makes it possible to
establish maximum work time (T)
according to use frequency (F).
With reference to standard IEC
34-1, the FALCON gearmotor,
with service type S3, can oper-
ate at use frequency of 40%.
To ensure efficient operation,
operate in the work range under
the curve.
Important: The curve is
obtained at a tempera-
ture of 20°C. Exposure to
the direct sun rays can
reduce use frequency
down to 20%.
Calculation of use frequency
The percentage of effective work time (opening + closing) compared to
total time of cycle (opening + closing + pause times).
Calculation formula:
% F =
Ta + Tc + Tp + Ti
where:
Ta = opening time
Tc = closing time
Tp = pause time
Ti = interval time between one complete cycle and another
4. ELECTRONIC DEVICES (standard system)
Pos. Description
Gearmotor

Photocell transmitter

Photocell receiver

Key-operated selector switch

Flashing light

External receiver (optional)

7
Ta + Tc
X 100
Connection cable
3x2.5 mm (230/115V~)
2
4x2.5 mm (400V~)
2
2x0.5 mm (TX)
2
4x0.5 mm (RX)
2
2x0.5 mm
2
2x1.5 mm
2
3x0.5 mm
2
Fig. 2
Fig. 3