Table of Contents
Advertisement
– Keep all bystanders away. Before backing up,
look to the rear and ensure that no one is behind
the vehicle. Back up slowly.
– Watch out for traffic when near or crossing roads.
Always yield the right of way to pedestrians and
other vehicles. This vehicle is not designed for
use on streets or highways. Always signal your
turns or stop early enough so other persons
know what you plan to do. Obey all traffic rules
and regulations.
– Never operate the vehicle in or near an area
where there is dust or fumes in the air which are
explosive. The electrical and exhaust systems
of the vehicle can produce sparks capable of
igniting explosive materials.
– Always watch out for and avoid low overhangs
such as tree limbs, door jambs, over head
walkways, etc. Make sure there is enough room
over head to easily clear the vehicle and your
head.
– If ever unsure about safe operation, stop work
and ask your supervisor.
• Do not touch engine, transaxle, radiator, muffler or
muffler manifold while engine is running or soon
after it has stopped because these areas may be hot
enough to cause burns.
• If the machine ever vibrates abnormally, stop
immediately, turn engine off, wait for all motion
to stop and inspect for damage. Repair all damage
before resuming operation.
• Before getting off the seat:
– Stop movement of the machine.
– Shut engine off and wait for all movement to
stop.
– Set parking brake.
– Remove key from ignition.
• Lightning can cause severe injury or death. If
lightning is seen or thunder is heard in the area, do
not operate the machine; seek shelter.
Maintenance
• Before servicing or making adjustments to the
machine, stop the engine, set the parking brake, and
remove the key from ignition to prevent accidental
starting of the engine.
• Make sure all hydraulic line connectors are tight, and
all hydraulic hoses and lines are in good condition
before applying pressure to the system.
• Keep your body and hands away from pin hole
leaks or nozzles that eject hydraulic fluid under
high pressure. Use paper or cardboard, not hands,
to search for leaks. Hydraulic fluid escaping under
pressure can have sufficient force to penetrate skin
and do serious damage. If fluid is injected into the
skin it must be surgically removed within a few
hours by a doctor familiar with this form of injury
or gangrene may result.
• To make sure the entire machine is in good condition,
keep all nuts, bolts, and screws properly tightened.
• To reduce the potential fire hazard, keep the engine
area free of excessive grease, grass, leaves, and
accumulation of dirt.
• If the engine must be running to perform a
maintenance adjustment, keep hands, feet, clothing,
and any parts of the body away from the engine and
any moving parts. Keep everyone away.
• Do not overspeed the engine by changing the
governor settings. The maximum engine speed is
3650 RPM. To ensure safety and accuracy, have an
Authorized Toro Distributor check the maximum
engine speed with a tachometer.
• If major repairs are ever needed or assistance is
required, contact an Authorized Toro Distributor.
• To be sure of optimum performance and safety,
always purchase genuine Toro replacement parts and
accessories. Replacement parts and accessories made
by other manufacturers could be dangerous. Altering
this vehicle in any manner may affect the vehicle's
operation, performance, durability or its use may
result in injury or death. Such use could void the
product warranty of The Toro® Company.
• This vehicle should not be modified without
The Toro® Company's authorization. Direct any
inquiries to The Toro® Company, Commercial
Division, Vehicle Engineering Dept., 8111 Lyndale
Ave. So., Bloomington, Minnesota 55420–1196.
USA
Sound Pressure
This unit has a sound pressure level at the operator's
ear of 82 dBA, which includes an Uncertainty Value (K)
of 1 dBA.
The sound pressure level was determined according to
the procedures outlined in EN ISO 11201.
Vibration
Hand-Arm
• Measured vibration level for right hand = 0.41 m/s
6
2
Advertisement
Table of Contents
