Remote Control - Yamaha HTR-5240 Owner's Manual

TROUBLESHOOTING
• Remote control
SYMPTOM CAUSE
REMEDY
Refer to
page
The remote control does Ditect sunlight or lighting (ftom an inverter
Reposition the unit 3
not work type of fluorescent lamp, etc) is striking the
temote control sensor of this unit
The batteties me weak
Replace all battet ies with new ones
2
The unit or other The component to be conttolled has not been
Pt ess one of the component selector buttons
40
component cannot be selected
which corresponds to the component to be
controlled controlled
The manufacturer's code has not been set Enter the code again 45
propetly
Try setting another code for the same
manufactUl er
• Others
SYMPTOM
CAUSE REMEDY
Refer to
page
The sound is degraded This unit is in the standby mode
TUln on the power of the unit
-
when listening with
headphones to a tape
deck or CD player
connected to this unit
There is noise The unit is too close to the digital Ol high-
Move the unit fUl thet away from such -
interference from digital
frequency equipment
equipment
or high-frequency
equipment, or the unit
• When playing back a source encoded with DTS
SYMPTOM
CAUSE REMEDY
Refer to
page
A loud hissing noise is The player which plays back the source is not The playet must be connected to a digital audio 13
heard when playing back
connected to a digital audio signal input
signal input tetminal of this unit besides the
a source encoded with ter minal of this unit analog audio signal terminal connections
DTS
The input mode is set to ANALOG on this unit Set a ptoper input mode to tUln on the built-in
22
DTS decodet
A percussive noise is If the input mode is set to AUTO, depending on Set the input mode of the currently selected 22
heard when playing back some sources, thete may be a noise hemd while input SOUlce to DTS
a source encoded with this unit is identifying the format of the input
DTS signal
No sound is heard when
The built-in DTS decoder does not function Set the player's digital volume control at the -
playing back a source because the player has a digital volume conttol
maximum, neutlal Ol ineffective position
encoded with DTS, even and it is set at a position othet than
if the input mode is set "maximum," "neutral" Ol "ineffective"
to AUTO on this unit
No sound is heard when A SOUl ce encoded with DTS cannot be recOl ded
~
-
playing back an MD or
on an MD Ol DAT
DAT on which has been
recorded a source
encoded with DTS
No sound is heard when
In the AUTO mode, the DTS-decoding mode Set the input mode to AUTO again 23
playing back a source
cannot be automatically changed to the nOl mal
(CD, etc) even if the
(PCM) digital signal input mode
currently selected input
mode is AUTO
• It is necessmy to use a DTS decodet to play back a sOUlce encoded with DTS, so the playet which plays back the sOUlce must be connected
to a digital audio input terminal of this unit in the way described in this manual If this connection is not made Ol only a D-to-A convertet is
being used without using a DTS decoder, only a loud hissing noise will be hemd when you play back the source
• If you make a semch (or skip, etc) operation while playing back a source encoded with DTS, the
"cIts"
indicator goes off This is because
this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode to ptevent a noise from being
output
I
49
TROUBLESHOOTING
• Remote control
SYMPTOM CAUSE
REMEDY
Refer to
page
The remote control does Ditect sunlight or lighting (ftom an inverter
Reposition the unit 3
not work type of fluorescent lamp, etc) is striking the
temote control sensor of this unit
The batteties me weak
Replace all battet ies with new ones
2
The unit or other The component to be conttolled has not been
Pt ess one of the component selector buttons
40
component cannot be selected
which corresponds to the component to be
controlled controlled
The manufacturer's code has not been set Enter the code again 45
propetly
Try setting another code for the same
manufactUl er
• Others
SYMPTOM
CAUSE REMEDY
Refer to
page
The sound is degraded This unit is in the standby mode
TUln on the power of the unit
-
when listening with
headphones to a tape
deck or CD player
connected to this unit
There is noise The unit is too close to the digital Ol high-
Move the unit fUl thet away from such -
interference from digital
frequency equipment
equipment
or high-frequency
equipment, or the unit
• When playing back a source encoded with DTS
SYMPTOM
CAUSE REMEDY
Refer to
page
A loud hissing noise is The player which plays back the source is not The playet must be connected to a digital audio 13
heard when playing back
connected to a digital audio signal input
signal input tetminal of this unit besides the
a source encoded with ter minal of this unit analog audio signal terminal connections
DTS
The input mode is set to ANALOG on this unit Set a ptoper input mode to tUln on the built-in
22
DTS decodet
A percussive noise is If the input mode is set to AUTO, depending on Set the input mode of the currently selected 22
heard when playing back some sources, thete may be a noise hemd while input SOUlce to DTS
a source encoded with this unit is identifying the format of the input
DTS signal
No sound is heard when
The built-in DTS decoder does not function Set the player's digital volume control at the -
playing back a source because the player has a digital volume conttol
maximum, neutlal Ol ineffective position
encoded with DTS, even and it is set at a position othet than
if the input mode is set "maximum," "neutral" Ol "ineffective"
to AUTO on this unit
No sound is heard when A SOUl ce encoded with DTS cannot be recOl ded
~
-
playing back an MD or
on an MD Ol DAT
DAT on which has been
recorded a source
encoded with DTS
No sound is heard when
In the AUTO mode, the DTS-decoding mode Set the input mode to AUTO again 23
playing back a source
cannot be automatically changed to the nOl mal
(CD, etc) even if the
(PCM) digital signal input mode
currently selected input
mode is AUTO
• It is necessmy to use a DTS decodet to play back a sOUlce encoded with DTS, so the playet which plays back the sOUlce must be connected
to a digital audio input terminal of this unit in the way described in this manual If this connection is not made Ol only a D-to-A convertet is
being used without using a DTS decoder, only a loud hissing noise will be hemd when you play back the source
• If you make a semch (or skip, etc) operation while playing back a source encoded with DTS, the
"cIts"
indicator goes off This is because
this unit automatically changes the DTS-decoding mode to the standard (PCM) digital signal input mode to ptevent a noise from being
output
I
49