Skin Tone Dtl; Knee/Level - Panasonic AJ-SPX800P Operating Instructions Manual

8-3-8 SKIN TONE DTL

Items/ Adjustable
Data Saved Range
SKIN TONE ON
DTL OFF
S C U F E
SKIN TONE ON
ZEBRA OFF
S C U F E
SKIN DTL 0
CORING :
5
:
S C U F E 7
SKIN TONE
GET
– – – – –
Y MAX 000
:
190
:
S C U F E
255
Y MIN 000
:
010
:
S C U F E
255
I CENTER 000
:
022
:
S C U F E 255
I WIDTH 000
:
010
:
S C U F E 255
Q WIDTH 000
:
005
:
S C U F E 255
Q PHASE –128
:
+000
:
S C U F E +127
R-Y
Q-WIDTH
I-WIDTH
I-CENTER
–
direction
Downloaded From VideoCamera-Manual.com Manuals
Remarks
Set the skin tone DTL to ON or OFF.
ON/OFF switching for ZEBRA within the
SKIN TONE range.
Adjust the effect of SKIN TONE DTL
CORING.
Used when obtaining the target hue for
SKIN TONE DTL. Align the center marker
and the target object with each other.
Set the maximum value of the brightness
signal to which SKIN TONE effect is
enabled.
Set the minimum value of the brightness
signal to which the SKIN TONE effect is
enabled.
Set the center position on the I axis (the
area where SKIN TONE is enabled).
Set the area width where SKIN TONE is
enabled along the I axis above and below
the I CENTER.
Set the area width where SKIN TONE is
enabled along the Q axis above and below
the I CENTER.
Set the phase in the area where SKIN TONE
is enabled based on the Q axis.
+ direction
Q-PHASE
B-Y
= SKIN TONE AREA

8-3-9 KNEE/LEVEL

Items/ Adjustable
Data Saved
MASTER PED –200
:
+000
:
S C U F E +200
MANUAL ON
KNEE OFF
S C U F E
KNEE POINT 70.0%
:
85.0%
:
S C U F E 107.0%
KNEE SLOPE 00
:
50
:
99 (98)
S C U F E
WHITE CLIP ON
OFF
S C U F E
WHITE CLIP 90%
LVL :
105%
:
S C U F E 109%
A.KNEE POINT 80%
:
85%
:
S C U F E 107%
A.KNEE LVL 100
:
105
:
S C U F E 109
A.KNEE 1
RESPONSE :
4
S C U F E
<Note>
The items indicated by
SW( ) R/W in the <SD CARD R/W SELECT> screen. The items
without are the setting items for PAINT MENU LEVEL R/W.
Y
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the preset
Y-MAX
mode.
Y-MIN
0
Remarks
Range
Set the master pedestal.
Set the mode when the AUTO KNEE switch
is OFF. The KNEE POINT/SLOPE set value
is enabled when this setting is ON.
Set the KNEE POINT position in 0.5% steps.
Set the KNEE SLOPE.
0 setting is equal to KNEE OFF.
<Note>
The adjustable range when using the AJ-
EC3P is from 00 to 98.
Set the WHITE CLIP feature to ON or OFF.
The WHITE CLIP LVL set value is enabled
when this setting is ON.
Set WHITE CLIP LEVEL.
Set the AUTO KNEE POINT position in
0.5% steps. This setting is enabled when the
OUTPUT/AUTO KNEE selector switch is set
to CAM.AUTO KNEE ON.
Set the AUTO KNEE LEVEL.
Set the AUTO KNEE response speed.
The smaller the setting value, the faster the
response speed.
are the setting items for PAINT MENU
8
107