Lcd Monitor - Panasonic AJ-SPX800P Operating Instructions Manual

Mode indication
W: Stays illuminated in 16:9 mode.
DV: Stays illuminated when the recording/playback format is DV.
GPS: Stays illuminated when radio waves are not received during
GPS operation.
GPS : Stays illuminated when radio waves are received during GPS
operation.
P-REC: Stays illuminated when PRE RECORDING is not set to 0
seconds, and blinks when recording is continued after the
recording tally lamp has gone out.
iREC: Remains illuminated during INTERVAL REC mode recording,
and blinks during a pause.
i: Blinks when INTERVAL REC mode is selected.
NDF SLAVE HOLD W
CTL VTCG TIME DATE P- REC
h Y minM
MEDIA
E
BATT
E
LOOP
Time code indication
NDF: Stays illuminated when the time code is in non-drop frame
mode.
DF: Stays illuminated when the time code is in drop frame mode.
SLAVE:Stays illuminated when the time code is externally locked.
HOLD: Stays illuminated when the time code generator/reader value
is frozen.
CTL: Stays illuminated when the DISPLAY switch is positioned at
[CTL] to display the CTL count.
TCG: Stays illuminated when the DISPLAY switch is positioned at
[TC] (or [UB]) to display the TC (or UB) generator value.
TC: Stays illuminated when the DISPLAY switch is positioned at
[TC] (or [UB]) to display the TC (or UB) reader value.
VTCG: Stays illuminated when the DISPLAY switch is positioned at
[UB] to display the VIUB generator value.
VTC: Stays illuminated when the DISPLAY switch is positioned at
[UB] to display the VIUB reader value.
TIME: Stays illuminated when the DISPLAY switch is positioned at
[UB] to display the real-time hour, minute and second.
DATE: Stays illuminated when the DISPLAY switch is positioned at
[UB] to display the real-time date.
No Indication:
The CTL, VTCG, TIME, and DATE stay off when the DISPLAY
switch is positioned at [UB] to display real time, time zone, hour and
minute.
Time count indication:
The time code, CTL, user bits and real time are shown.
<Note>
When the DISPLAY switch is positioned at UB, each press of the
HOLD button changes the indication through VTCG (VTC)
TIME No Indication (Time Zone)
Downloaded From VideoCamera-Manual.com Manuals
20
DV GPS
OVER
0
10
s D frm 20
F
30
F
40
OO
13
DRIVE OP-SLOT -dB
TCG (TC), in that order.
Positions of time code-related switches and
information provided
Position of DISPLAY
switch
CTL
TC
UB
OVER

2-9 LCD Monitor

24
LCD monitor
The LCD monitor displays the video in the viewfinder.
Alternatively, it can show clips on the P2 card in a thumbnail
format.
In thumbnail display mode, clips can be edited or deleted, or
P2 cards can be formatted using the
and
OPEN button
Used to open the LCD monitor.
THUMBNAIL button
This button switches the content on the
from the video in the viewfinder to clip thumbnails. Another
press switches them back to the video from the viewfinder.
DATE
Note that this switchover is not performed during a recording
or playback.
MENU BAR button
In thumbnail display mode, this button allows you to
manipulate the menu bar (e.g., to delete clips).
CURSOR and SET buttons
The four triangular buttons are the CURSOR buttons, and
the center rectangular one is the SET button.
They are used to select a thumbnail and manipulate the
menu bar.
Manipulating Clips with Thumbnails].
Position of TCG
switch
SET
F-RUN or R-RUN
F-RUN/SET/
R-RUN
CURSOR and SET buttons.
For more information,
Information Item
Time code
CTL
Time code
User's bit or real-
time, time zone
MENU BAR button
LCD monitor
see [Chapter 6