Tc/Ub - Panasonic AJ-SPX800P Operating Instructions Manual

8-6-6 TC/UB

Items/ Adjustable
Data Saved Range
TC MODE DF
NDF
– C U F –
UB MODE USER
TIME
DATE
EXT
TCG
FRM RATE
REGEN
– C U F –
VITC UB MODE USER/EXT
TIME
DATE
TCG
FRM RATE
REGEN
– C U F –
TCG SET HOLD ON
OFF
– C U F –
Downloaded From VideoCamera-Manual.com Manuals
120
Remarks
Set the time code mode.
DF: Drop frame.
NDF: Non drop frame.
<Note>
Regardless of the setting of this option, the
AJ-SPX800P always operates in non-drop-
frame for 24P and 24PA modes.
Select the user bits mode.
USER:Select UB value set in the LCD
section.
TIME: Select local time (hours, minutes,
seconds).
DATE: Select local date and time (2 last
digits of year, month, date, time).
EXT: When "CAM" or "VIDEO" is selected
in the menu option REC SIGNAL in
the SYSTEM MODE screen, user's
bit input to the TC IN connector is the
reference.
When "1394" is selected, user's bit
input to the DVCPRO/DV connector
is the reference.
If reading fails, USER value is
retained.
TCG: TCG value enters UB.
FRM RATE:
Select same camera shoting
information (frame rate, etc.) with the
VAUX UB (VITC UB).
REGEN:Read out value stored in the card
and record value continuously.
Select the user bits mode for VAUX TC
(VITC).
USER/EXT:
If UB MODE is set to EXT, the EXT
value is recorded. If not, USER value
set by UB is recorded.
TIME: Select local time (hours, minutes,
seconds).
DATE: Select local date and time (2 last
digits of year, month, date, time).
TCG: TCG value enters UB.
FRM RATE:
Select same camera shoting
information (frame rate, etc.) with the
VAUX UB (VITC UB).
REGEN:Read out value stored in card and
record value continuously.
<Note>
The AJ-SPX800P always operates in FRM
RATE for 24P and 24PA modes. For more
information, refer to the 24P VITC UB items.
The menu option 24P VITC UB is found in
the OPTION screen on the OPTION MENU
page.
ON/OFF switching for the feature that
always starts recording (when the power is
turned ON again) the TCG value that was
set before the power is turned OFF.
Items/ Adjustable
Data Saved Range
FIRST REC TC REGEN For the first recording after the power is
turned on, a P2 card is inserted and then
PRESET
switching from this P2 card to another
recording-target P2 card is performed,
select whether or not to regenerate the time
code as the value on the new P2 card.
REGEN:For clips recorded on the recording-
PRESET:
Use the camera-recorder's internal time
code.
<Notes>
Set the date and time accurately. For
guidance on setting, see [4-5-2 Setting
the Internal Clock's Date and Time].
During operation in either 24P or 24PA
mode, regeneration of the value of the
card recorded in drop-frame is not
permitted.
– C U F –
P.OFF LCD ON Select whether or not to display the time
code setting and counter indication on the
DISPLAY OFF
LCD monitor when the power is turned OFF.
ON: Display setting and indication while the
OFF: Power-down LCD monitor while
– C U F –
TC OUT TCG Select the time code to be output to the time
code output connector.
TCG/TCR
TCG:Always output time code generator
TCG/TCR:
– C U F –
TC DISP SEL 30F Select the display format for the time code
frame digits.
24F
30F: Display time code frame digits in 30
24F: Convert time code frame digits into 24
– C U F –
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
target P2 card, regenerate the time
code as the time code of the clip that
has the most recent date and time.
power is turned OFF.
camera power is turned OFF. Setting
and indication disabled.
value.
Display time code generator value in
E-E mode, and time code reader value
in V-V mode.
frames.
frames for display.