Drainage; Programming The Machine; Selecting The Language - Saeco Royal SUP 015 User's And Maintenance Booklet

32
26 Remove the water tank (11) from the
machine, remove its cover (12) and fill it with
cold water (approx. 2.4 l). A valve on the tank
bottom prevents water from escaping.
Before installing the water tank in the
machine, make sure the coffee bean
container cover is properly fitted.
Install the water tank, slightly pressing over it to
fit the valve which will open automatically.
Replace the cover on the tank.
Do not fill the tank with an excessive
quantity of water.
Always fill the tank with fresh water:
hot water as well as other fluids
might damage the tank.
Do not switch on the machine if the
water tank is empty. Before using
the machine make sure there is enough water in
the tank.
Connect the plug to the socket and press the
main switch.
The display shows
WARMING UP
ENERGY
Should (1/2) be displayed,
SAVING
press the Energy saving switch to disactivate the
energy saving mode.

Drainage

Direct the steam/hot water dispensing tube (7)
over the drip tray (2). Place a cup or another
suitable container under the dispensing tube,
then turn the steam/hot water knob (9)
counterclockwise. The pump starts automati-
cally. Wait until a regular water jet is obtained,
then close the knob. The machine is now
drained and ready to work.
The display shows
HOT WATER
READY FOR USE
DRAINAGE
Important: It is advisable to drain the machine
before the first start, after a prolonged period
the machine has not been used or whenever the
water tank has been completely emptied. Fur-
thermore, should the pump be defective, the
display shows
VENTILATE
Programming
the coffee machine
27 To enter the programming mode, press the
key ENT (pre-ground coffee) when the machine
is on and keep it pressed until the first two lines
of the programming mode are displayed:
LANGUAGE
WATER HARDN
At the end of the line appears a blinking
asterisk, which can be moved up and down
with the keys (tall and regular coffee).
The display shows the following items in this
sequence:
LANGUAGE PREGRINDING
RINSING CYCLE FUNCTION TOTAL COFFEE
WATER HARDN. DESCALING
CUP HEATER SIGN. DESCAL.
TEMPERATURE TIMER
PREBREWING RISING CYCLE
Then, press ESC. The machine is now in the
normal mode again.
Selecting menu items
Select the different menu items by means of the
keys . The key ENT allows you to
activate the selected item. It is possible to
modify the selected figures in a menu item using
. The key ENT memorizes the
the keys
selected options, for instance <<on>> for the
item cup heater.
33
Should you accidentally change some data,
press ESC to leave the menu item without saving
the new options which were selected acciden-
tally.

Selecting the language

Move the asterisk at the end of the line to the
menu item <<language>> using the keys
. Press ENT to activate this item.
The display shows:
1 LANGUAGE
ENGLISH
The keys allow you to change the set
options: italiano, français, Deutsch, english,
español, português.
Rinsing cycle function
If the rinsing cycle function is activated, the
machine that is started after a period of inactiv-
ity starts a water rinsing cycle to the coffee
dispensing units automarically.
Move the asterisk to the menu item <<Rinsing
cycle>> using the keys und press ENT to
active it.
The display shows:
RINSING CYCLE
ON
You can modify the chosen item with the
key : on; off.
Water hardness adjustment
In order to adjust the water hardness, it is
necessary to test the water using the strip
supplied with the machine. Dip the strip into the
water for a second, shake off excess water
gently, wait approx. 1 minute and read the
results.
Move the asterisk at the end of the line to the
menu item <<Water hardn.>> using the keys
SELECTING THE LANGUAGE
. Press ENT to activate this item.
The display shows:
2 WATER HARDN
HARDNESS 2
The keys allow
you to change the set
options:hardness 1 (very
Sehr weiches Wasser Hardness 4
soft), hardness 2 (soft),
Weiches Wasser Hardness 3
hardness 3 (medium),
Mittleres Wasser
Hardness 2
hardness 4 (hard).
Hartes Wasser Hardness 1
Activating the cup heater
Move the asterisk at the end of the line to the
menu item <<cup heater>>. Press ENT to
activate this function.
The display shows:
3 CUP HEATER
ON
The keys allow you to change the set
options: on, off.
Selecting temperature
Move the asterisk at the end of the line to the
menu item <<temperature>> using the
keys . Press ENT to activate this item.
The display shows:
4 TEMPERATURE
MEDIUM
The keys allow you to change the set
options: minimum, low, medium, high, maxi-
mum.
Selecting the prebrewing
function
As soon as the coffee has been moistened, the
pump stops for a while. Then, the brewing cycle
continues.
Move the asterisk at the end of the line to the
menu item <<pre-brewing>> using the keys
. Press ENT to activate this function.
The display shows:
5 PREBREWING
ON