Drainage; Programming The Coffee Machine; Selecting The Language - Saeco SUP 015 User's And Maintenance Booklet

15
Never fill the coffee bean container with other
products. They might damage the machine!
Before filling the container with coffee beans,
make sure the pre-ground coffee container is
closed to prevent coffee beans from falling into
it. They might damage the machine!.
Remove the water tank (11) from the machine,
remove its cover (12) and fill it with cold water
(approx. 2.4 l). A valve on the tank bottom
prevents water from escaping.
Before installing the water tank in the
machine, make sure the coffee bean
container cover is properly fitted.
26
Install the water tank, slightly pressing over it to
fit the valve which will open automatically.
Replace the cover on the tank.
Do not fill the tank with an excessive quantity of
water.
Always fill the tank with fresh water: hot water
as well as other fluids might damage the tank.
Do not switch on the machine if the water tank
is empty. Before using the machine make sure
there is enough water in the tank.
Connect the plug to the socket and press the
main switch.
The display shows
"WARMING UP...... "

DRAINAGE

Should
"ENERGY
"SAVING
be displayed, press the Energy saving switch to
disactivate the energy saving mode.
Drainage
Direct the steam/hot water dispensing tube (7)
over the drip tray (2). Place a cup or another
suitable container under the dispensing tube,
then turn the steam/hot water knob (9)
counterclockwise. The pump starts automati-
cally. Wait until a regular water jet is obtained,
then close the knob. The machine is now
drained and ready to work.
The display shows
"SELECT PRODUCT
"READY FOR USE
Important: It is advisable to drain the ma-
chine before the first start, after a prolonged
period the machine has not been used or
whenever the water tank has been completely
emptied. Furthermore, should the pump be
defective, the display shows
"VENTILATE
Programming
the coffee machine
27
To enter the programming mode, press the key
ENT (pre-ground coffee) when the machine is
on and keep it pressed until the first two lines of
the programming mode are displayed:
"LANGUAGE
"RINSING
At the end of the line appears a blinking
asterisk, which can be moved up and down
16
with the keys
"
The display shows the following items in this
"
sequence:
LANGUAGE
RINSING
WATER HARDN.
CUP HEATER
TEMPERATURE
PREBREWING
Then, press ENT. The machine is now in the
normal mode again.
Selecting menu items
Select the different menu items by means of the
keys . The key ENT allows you to
activate the selected item. It is possible to
"
modify the selected figures in a menu item using
"
. The key ENT memorizes the
the keys
selected options, for instance ON for the item
cup heater.
Should you accidentally change some data,
press ESC to leave the menu item without saving
the new options which were selected acciden-
tally.
"

Selecting the language

Move the asterisk at the end of the line to the
menu item LANGUAGE using the keys
Press ENT to activate this item.
The display shows:
The keys allow you to change the set
"
options: Deutsch, italiano, français, english,
"
español, portugues.
(tall and regular coffee).
Rinsing cycle function
In the rinsing cycle function is activated, the
machine that is started after a priod of inactivity
starts a water rinsing cycle yo the cofee dispens-
PREGRINDING ing units automarically.
TOTAL COFFEES
DESCALING Move the asterisk to the menu item RINSING
SIGNAL. DESCAL. CYCLE using the keys
TIMER activate it.
RINSING CYCLE The display shows:
You can modify the closen item with the
keys
Water hardness adjustment
In order to adjust the water hardness, it is
necessary to test the water using the strip
supplied with the machine. Dip the strip into the
water for a second, shake off excess water
gently, wait approx. 1 minute and read the
results.
Move the asterisk at the end of the line to the
menu item WATER HARDN. using the keys
. Press ENT to activate this item.
The display shows:
.
"LANGUAGE "
"ENGLISH "
Hardness 4
Hardness 3
Hardness 2
Hardness 1
SELECTING THE LANGUAGE
und press ENT to
"RINSING "
"ON "
: on, off.
"WATER HARDN. "
"HARDNESS 2 "
The keys allow
you to change the set
options: hardness 1
(very soft), hardness 2
(soft), hardness 3 (me-
dium), hardness 4
(hard).