Read This First; Setting Up The Speaker Systems; Connections..................................................5 - Denon AVR-1802 Operating Instructions Manual

Av surround receiver
Hide thumbs Also See for AVR-1802:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1

6 READ THIS FIRST

This A / V surround Receiver must be setup before use. Following these steps.
Step 1
(page 5 to 8)
Choose the location to setup the speakers and connecting the components.
Step 2
(page 9)
Next, insert the batteries into the remote control unit.
Step 3
(page 9 to 11)
Finally, setting up the system.

7 SETTING UP THE SPEAKER SYSTEMS

2 Speaker system layout
Basic system layout
• The following is an example of the basic layout for a system consisting of six speaker systems and a television
monitor:
Subwoofer
Front speaker systems
Set these at the sides of the TV or
screen with their front surfaces as
flush with the front of the screen as
possible.
Center speaker system
Surround speaker systems
8 CONNECTIONS
• Do not plug in the power cord until all connections
have been completed.
• Be sure to connect the left and right channels
properly (left with left, right with right).
• Insert the plugs securely. Incomplete connections
will result in the generation of noise.
• Use the AC OUTLET for audio equipment only. Do
not use them for hair driers, etc.
• Analog recording of signals input to the AVR-1802 in digital format is not possible. To record in analog, also
connect the analog signals of the player to the AVR-1802's analog input terminals.
• The AVR-1802's OPTICAL OUT terminal is an optical digital output terminal for connection of a CDR
recorder, MD recorder or other digital recording device. Use it for digital recording.
Connecting the audio components (1)
Connecting a turntable
Connect the turntable's output cord to this
unit's PHONO jacks, the L (left) plug to
the L jack, the R (right) plug to the right
jack.
INPUT
OUTPUT
NOTE:
R
L
R
L
This unit cannot be used with MC
cartridges directly. Use a separate
R
R
L
L
head amplifier or step-up transformer.
If humming or other noise is generated
when the ground wire is connected,
disconnect the ground wire.
Turntabie
(MM cartridge)
L
R
L
R
L
R
SIGNAL
PHONO
GND
Ground wire
ANTENNA TERMINALS
CD
LOOP
AM
ANT.
DVD /
VDP
FM
TV /
COAX.
COAX.
DBS
75
L
VCR
-1
R
VCR
FR
FL
OPT-1
-2
VCR
SW
C
OPT-2
-1
VCR
OPT-2
SR
SL
-2
R
L
EXT. IN
AUDIO
DIGITAL
VIDEO
AC OUTLETS
AUDIO OUT
• SWITCHED (capacity – 100 W)
The power to these outlets is turned on and off in conjunction with the POWER
switch on the main unit, and when the power is switched between on and standby
from the remote control unit.
Decoders with 6-channel
No power is supplied from these outlets when this unit's power is at standby. Never
analog outputs, etc.
connect equipment whose capacity is above 100 W.
NOTE:
Only use the AC OUTLET for audio equipment. Never use them for hair driers, TVs or
other electrical appliances.
• Note that binding pin plug cords together with power
cords or placing them near a power transformer
will result in generating hum or other noise.
• Noise or humming may be generated if a connected
audio equipment is used independently without
turning the power of this unit on. If this happens,
turn on the power of this unit.
Connecting a tape deck
Connections for recording:
Connect the tape deck's recording input jacks
(LINE IN or REC) to this unit's tape recording
(OUT) jacks using pin plug cords.
Connections for playback:
Tape deck or CD recorder
Connect the tape deck's playback output jacks
(LINE OUT or PB) to this unit's tape playback (IN)
jacks using pin plug cords.
Connecting the pre-out jacks
Use these jacks if you wish to connect external power amplifier(s) to
increase the power of the front and center channels, or for connection
to powered loudspeakers.
Connect the internal amplifier's subwoofer to the subwoofer terminal.
(Refer to page 8.)
AC CORD
AC 230 V, 50 Hz
CDR /
TAPE
CDR /
TAPE
DVD/
TV/
VCR-1
VCR-2
VCR-1
VCR-2 MONITOR
VDP
DBS
AC OUTLET
S-VIDEO
MONITOR
FRONT
CENTER
DVD /
VDP
SUB
TV /
WOOFER
DBS
PREOUT
SPEAKER SYSTEMS
AC 230V 50Hz
VCR-1
FRONT
CENTER
SURROUND
SWITCHED
100W MAX.
VCR-2
VCR-1
VCR-2
SPEAKER IMPEDANCE
FRONT A OR B / 6 16
CENTER
/ 6 16
A + B / 12 16
SURROUND / 6 16
Connecting the AC OUTLET
ENGLISH
5

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents