Denon AVR-1802 Operating Instructions Manual page 11

Setting the delay time
Input the distances from the listening position to the speakers and set the surround
delay time.
Preparations:
Measure the distances from the listening position to the speakers (L
diagram at the right).
L : Distance from center speaker to listening position
1
L : Distance from front speakers to listening position
2
L : Distance from surround speaker to listening position
3
CAUTION:
Set the center speaker at the same distance from the front speakers (left and right) or the subwoofer, or so
that the difference in distance (L – L ) is 1.5 meters or less.
2 1
Set the surround speakers (left and right) at the same distance from the front speakers (left and right) or the
subwoofer, or so that the difference in distance (L
1
Use the (left) and
speakers and subwoofer to the listening position.
6 FRNT/SW
• The number changes in units of 0.1 meter each time one of the buttons is
pressed. Select the value closest to the measured distance.
("/SW" appears only when subwoofer = yes.)
Press the SELECT or
NOTE:
• The speaker distance can be adjusted between 0 and 18 meters in steps of 0.1 meter.
2
Use the (left) and
speakers to the listening position.
7 CENTER
• The number changes in units of 0.1 meter each time one of the buttons is
pressed. Select the value closest to the measured distance.
Press the SELECT or
NOTE:
• No setting when "None" has been selected for the center speaker.
3
Use the (left) and
speakers to the listening position.
8 SURR.
• The number changes in units of 0.1 meter each time one of the buttons is
pressed. Select the value closest to the measured distance.
Press the SELECT or
DIGITAL input (COAX) setting.
NOTE:
• No setting when "None" has been selected for the surround speakers.
FL Center
to L on the
L 1
1 3
L
2
L
3
SL
– L ) is 4.5 meters or less.
2 3
(right) buttons to set the distance from the front
3.6m
(down) button to switch to the center speaker setting.
(right) buttons to set the distance from the center
3.6m
(down) button to switch to the surround speaker setting.
(right) buttons to set the distance from the surround
3.0m
(down) button to enter the setting and switch the
Digital input setup
Input the type of components connected to the digital input terminals.
FR
1
Use the
to the COAXIAL input (COAXIAL) terminal.
Listening
position
9 COAX
SR
• Select "OFF" if nothing is connected.
Press the SELECT or
setting.
2
Use the
to the OPTICAL input 1 (OPT 1) terminal.
10 OPT1
• Select "OFF" if nothing is connected.
Press the SELECT or
setting.
3
Use the
to the OPTICAL input 2 (OPT 2) terminal.
11 OPT2
• Select "OFF" if nothing is connected.
Press the SELECT or
front the beginning.
NOTE:
• PHONO, TUNER and V. AUX cannot be selected.
After setting up the system
1
Press the SYSTEM button to finish system set up.
This completes the system setup operations. Once the system is set up, there is no need to make the settings
again unless other components or speakers are connected to or the speaker layout is changed.
(left) and (right) buttons to set the type of device connected
(Initial)
CD DVD TV VCR1 VCR2
DVD
(left) button (right) button
(down) button to switch the optical input 1 (OPT 1)
(left) and (right) buttons to set the type of device connected
(Initial)
CD DVD TV VCR1 VCR2
TV
(left) button (right) button
(down) button to switch the OPTICAL input 2 (OPT 2)
(left) and (right) buttons to set the type of device connected
CD DVD TV VCR1 VCR2
CDR
(left) button (right) button
(down) button if you want to start the settings over
ENGLISH
CDR OFF
CDR OFF
(Initial)
CDR OFF
11