Remote Control Unit - Denon AVR-1802 Operating Instructions Manual

ENGLISH

11 REMOTE CONTROL UNIT

Operating DENON audio components
DENON remote-controllable audio components can be controlled using this
unit's remote control unit. Note that some components, however, cannot be
operated with this remote control unit.
CD MD/CDR
1
AUDIO VIDEO
POWER
1
AVR/AVC TV VCR DVD/VDP
ON
PHONO CD DVD/VDP
OFF 1 2 3
V. AUX VCR-1 VCR-2 TV/DBS
4 5 6 7
2-c 2
INPUT MODE CDR / TAPE TUNER SHIFT
8 9 0
SURROUND
·
MODE TAPE VCR
6 7
CHANNEL
0
2-b
3 2 0
VIDE SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
8 3 9
2-a
2
6 7
SYSTEM SURROUND
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
CHANNEL TV VOLUME
B
REMOTE CONTROL UNIT RC-897
NOTE:
• Tape deck (TAPE) and tuner can be operated when the switch is at "AUDIO" position.
Preset memory (Audio component)
DENON components can be operated by setting the preset memory for MD or
CDR. Operation is not possible for some models.
CD MD/CDR
1
1
AUDIO VIDEO
POWER
AVR/AVC TV VCR DVD/VDP
ON
PHONO CD DVD/VDP
OFF 1 2 3
V. AUX VCR-1 VCR-2 TV/DBS
2
4 5 6 7
INPUT MODE CDR / TAPE TUNER SHIFT
8 9 0
SURROUND
TAPE · VCR
MODE
6 7
CHANNEL
0
3 2 0
2
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
8 3 9
2
6 7
SYSTEM SURROUND
2
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
CHANNEL TV VOLUME
B
REMOTE CONTROL UNIT RC-897
12
Set the slide switch to the position for the
component to be operated (CD or MD/CDR).
Use the buttons shown below to operate the audio component.
For details, refer to the respective component's manual.
a. For CD player and MD/CD recorder
, : Manual search
6 7
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
(reverse and forward)
TITLE
: Stop
2
8 3 9
: Play
1
2
6 7
, : Auto search
8 9
SYSTEM SURROUND
: Pause
3
DISC : Switch discs
SKIP+ (for CD changers only)
b. For tape deck (TAPE)
: Rewind
6
V. AUX VCR-1 VCR-2 TV/DBS
4 5 6 7
: Fast-forward
7
INPUT MODE CDR / TAPE TUNER SHIFT
: Stop
2
8 9 0
SURROUND
TAPE · VCR : Forward play
MODE 1
6 7
: Reverse play
0
CHANNEL
0
3 2 0
c. For TUNER
SHIFT : Switch preset channel range
V. AUX
VCR-1 VCR-2 TV/DBS
4 5 6 7
CHANNEL : Preset channel
INPUT MODE CDR / TAPE TUNER SHIFT
(+, –) (up/down)
8 9 0
SURROUND
·
MODE TAPE VCR
6 7
CHANNEL
0
3 2 0
Set the slide switch to "MD/CDR".
Holding in the PLAY (1) button, press the
button for the components you want to set.
(Refer to table 1.)
Table 1: Combinations of Personal System
Codes
MASTER
VOL.
MASTER
VOL.
MD CD-R
PLAY (1)
NOTE:
• The memory can only be preset for either the MD or the CDR.
Preset codes set upon shipment from the factory and when
reset.
Preset memory (Video component)
DENON and other makes of components can be operated by setting the preset memory for your make of video
component.
This remote control unit can be used to operate components of other manufacturers without using the learning
function by registering the manufacturer of the component as shown on the List of Preset Codes (page 171).
Operation is not possible for some models.
CD MD/CDR
AUDIO
VIDEO
CD MD/CDR
1
AUDIO VIDEO
POWER
AVR/AVC TV VCR DVD/VDP
2
ON
PHONO CD DVD/VDP
3
OFF 1 2 3
V. AUX VCR-1 VCR-2 TV/DBS
4 5 6 7
INPUT MODE CDR / TAPE TUNER SHIFT
2. 3
8 9 0
SURROUND
·
MODE TAPE VCR
6 7
CHANNEL
0
3 2 0
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
TITLE
8 3 9
2
6 7
SYSTEM SURROUND
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
RETURN DISPLAY
VOLUME
CHANNEL TV
B
REMOTE CONTROL UNIT RC-897
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation,
cover the remote control unit's transmitting window while setting the preset memory.
• Some models and years of manufacture of components of the manufacturers listed on the List of Preset
Codes cannot be used.
• The unit is equipped with several types of remote control codes which depend on the manufacturer. If there
is no operation, please change the preset code (a 2-digit number) and try again.
CD MD/CDR
AUDIO VIDEO
1 Set the slide switch to "VIDEO".
Holding in the SHIFT button q, press the POWER
2
button w of the components (DVD/VDP, VCR or
TV) you want to set.
Press and hold in the SHIFT button.
3 Holding in the SHIFT button q, press the number
buttons w to input the preset code (consisting of
2-digit numbers) for the manufacturer of the
component whose signals you want to store in
the memory.
See the list on page 171 for the preset codes
(consisting of 2-digit numbers).
To continue registering other components, repeat steps 2 to 3.
4
CD MD/CDR
AUDIO VIDEO
w
q
w
q