Sony F35 Operation Manual page 45

To apply monitor gamma to the monitor
picture
MONI GAMMA ENABLE
If this is set to ON, the monitor gamma (ITU-R709)
1)
appropriate for monitoring
output from the VF1, VF2, MONITOR OUT HD SDI 1/2,
or REMOTE connector. The video output signals from
those connectors are selected on the <MONITOR
OUTPUT> page.
This setting is effective when S-LOG gamma is applied to
the video output signals for recording intended for post-
production editing.
1) The VBS output signal always becomes the camera image to which ITU-
R709 gamma is applied.
Notes
• If the monitor gamma is activated with 23.98PsF/
S23.98PsF, the output for viewfinders and monitors is
switched to 59.94i. In the case of 24PsF/S24PsF, the
output is switched to 50i. To eliminate this phenomena,
change the DOWN CONVERTER setting on the
<POWER SAVE> page of the MAINTENANCE menu
from ACTIVE to PWR SAVE.
• Some of the paint settings (such as black gamma, knee,
detail, matrix, etc.) for the main line are not applied to
monitor gamma.
To monitor the playback picture
The playback picture of the recorder can be confirmed with
a monitor connected to the camera or on the viewfinder
2)
screen.
2) When MONI GAMMA ENABLE is set to OFF, the same gamma as that
applied to the main line is applied to all the outputs. However, the PB and
PB MIX modes can be independently selected for the VF, MONI, and VBS
signals.
PB
The playback-signal output mode can be selected for each
VF, MONI, or VBS signal.
Setting Signal
ON The playback picture of the recorder is always
output.
AUTO Normally, the camera image is output. When
the recorder enters playback mode (PLAY, FF,
REW, or REC REVIEW,) the playback picture
is automatically selected.
OFF The camera image is always output. (Default)
Note
If the recorder is turned off with PB ON, the picture on the
viewfinder/monitor screen is distorted. The normal picture
is restored by turning the recorder on or setting PB to
AUTO or OFF.
is applied to the video signals
To compare the playback picture and
camera image
The playback picture and camera image can be displayed
on the same screen when the playback-signal output mode
is set to ON or AUTO for the item PB on the <PB/MONI
GAMMA> page and if PB MIX is set to ON.
PB MIX
The playback-signal mix mode can be independently set to
ON or OFF for each VF, MONI, or VBS signal. When set
to ON, the playback picture and camera image are mixed.
How this is to be displayed can be set on the <PB MIX
SETTING> page of the USER (OPERATION) menu.
<PB MIX SETTING> page
< P B M I X S E T T I N G >
M I X T Y P E
M I X
D I R E C T I O N
M O D E
L E V E L
W I P E
L A Y O U T
P B P O S I T I O N : R I G H T
B O U N D A R Y
MIX TYPE
How the picture is to be displayed can be selected.
Setting How to display
MIX The playback picture and camera image are
overlapped. (Default)
WIPE The screen is horizontally or vertically split in
two, and two pictures are displayed
simultaneously.
MIX
When MIX TYPE is set to MIX, how to mix the pictures
can be selected.
Item Setting Content
DIRECTION CAM The playback picture is gradually
mixed into the camera image.
(Default)
PB The camera image is gradually
mixed into the playback picture.
MODE Y-MIX The Y signals are mixed. (Default)
WIRE(W) Only the outline components are
mixed and displayed with white
lines.
WIRE(B) Only the outline components are
mixed and displayed with black
lines.
LEVEL 0 to 80% The mix level can be adjusted.
(Default: 80%)
U 0 8
: M I X
B
: P B
: Y - M I X
: 8 0 %
: H O R
: 9 6 0
Setting the Camera Outputs
45