Toro Riding Mower Safety - Toro LT3340 Operator's Manual

•
Keep the ROPS in safe operating condition by
periodically thoroughly inspecting for damage and
keeping all mounting fasteners tight.
•
Replace a damaged ROPS. Do not repair or revise.
•
Do not remove the ROPS.
•
Any alterations to a ROPS must be approved by the
manufacturer.
Maintenance and Storage
•
Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
•
Never store the equipment with fuel in the tank inside a
building where fumes may reach an open flame or spark.
•
Allow the engine to cool before storing in any enclosure.
•
To reduce the fire hazard, keep the engine,
silencer/muffler, battery compartment and fuel storage
area free of grass, leaves, or excessive grease.
•
Keep all parts in good working condition and all hardware
and hydraulic fittings tightened. Replace all worn or
damaged parts and decals.
•
If the fuel tank has to be drained, do this outdoors.
•
Be careful during adjustment of the machine to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
•
On multi-cylinder/multi-cutterhead machines, take care
as rotating one cylinder/cutterhead can cause other
cylinders/cutterheads to rotate.
•
Disengage drives, lower the cutting units, set parking
brake, stop engine and remove key from ignition. Wait
for all movement to stop before adjusting, cleaning or
repairing.
•
Clean grass and debris from cutting units, drives,
silencers/mufflers, and engine to help prevent fires. Clean
up oil or fuel spillage.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect battery before making any repairs. Disconnect
the negative terminal first and the positive last. Reconnect
positive first and negative last.
•
Use care when checking the cylinders/cutterheads. Wear
gloves and use caution when servicing them.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Charge batteries in an open well ventilated area, away
from spark and flames. Unplug charger before connecting
or disconnecting from battery. Wear protective clothing
and use insulated tools.
Hauling
•
Use care when loading or unloading the machine into a
trailer or truck.
•
Use full width ramps for loading machine into trailer or
truck.
•
Tie the machine down securely using straps, chains, cable,
or ropes. Both front and rear straps should be directed
down and outward from the machine.

Toro Riding Mower Safety

The following list contains safety information specific to Toro
products or other safety information that you must know that
is not included in the safety standards.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
Use of this product for purposes other than its intended use
could prove dangerous to user and bystanders.
WARNING
Engine exhaust contains carbon monoxide, which
is an odorless, deadly poison that can kill you.
Do not run engine indoors or in an enclosed area.
•
Know how to stop the engine quickly.
•
Do not operate the machine while wearing tennis shoes
or sneakers.
•
Wearing safety shoes is advisable and required by some
local ordinances and insurance regulations.
•
Handle fuel carefully. Wipe up any spills.
•
Check the safety interlock switches daily for proper
operation. If a switch should fail, replace the switch
before operating the machine.
•
Before starting the engine, sit on the seat.
•
Using the machine demands attention. To prevent loss
of control:
– Do not drive close to sand traps, ditches, creeks, or
other hazards.
– Reduce speed when making sharp turns. Avoid
sudden stops and starts.
– When near or crossing roads, always yield the
right-of-way.
– Apply the service brakes when going downhill to
keep forward speed slow and to maintain control of
the machine.
•
Raise the cutting units when driving from one work area
to another.
•
Do not touch the engine, silencer/muffler, or exhaust
pipe while the engine is running or soon after it has
stopped because these areas could be hot enough to cause
burns.
6