Configuration 4 - Pbx To Pbx - Multitech DataTalker DT101 Owner's Manual

Data/voice/fax concentrator
Table of Contents

Advertisement

DataTalker Owner's Manual

2.5 Configuration 4 - PBX to PBX

Configuration 4 is a data/voice/fax configuration that uses two DataTalkers to link two PBXs.
Using a single ISDN composite link, they connect a minicomputer and a PBX E&M trunk at the
local site to a remote PC on the data part of the network and a second PBX E&M trunk on the
voice/fax channel. The configuration is shown in Figure 2-4.
Asynchronous
Channel
PC
PSTN
Remote Site
Figure 2-4. PBX to PBX Configuration
At both the local and the remote sites, connect the DATA/COMMAND connector on the
DataTalker to an asynchronous port on the computer; connect the DSU/TA DIGITAL jack on the
DataTalker to the jack for the ISDN service; and connect the VOICE/FAX CHANNEL 1 E&M jack
on the DataTalker to a PBX E&M trunk connector. When you are making an E&M connection,
you should also run a ground wire from the ground connector on back of the DataTalker or the
RackTalker rack to a ground connection on the PBX.
Before you install the DataTalkers, you must configure them. To configure a DataTalker, place
DIP switch position 3 in the down (closed) position and connect a command port device such as
a terminal or a PC to the DATA/COMMAND connector on the back of the DataTalker. Turn on the
DataTalker and PC and run your communications software in terminal mode. (Set it for direct
connection at a serial port speed of 19,200 bps or slower.) Press the ENTER key to establish
communications with DataTalker. The Main Menu will appear.
The Main Menu provides access to a series of configuration menus providing simple and
complete configuration information for each aspect of the DataTalker. From the Main Menu, you
can configure the unit, display statistics, reset various functions within the MMV, and run
diagnostic tests:
Main Menu
1 - Configurations
2 - Statistics
3 - Reset Options
4 - Diagnostics
5 - Exit Command Mode
6 - QUICK SETUP
Selection : _
To configure the DataTalker, enter 1 and press ENTER.
32
ISDN
Data / Voice / Fax Concentrator
FAX 2
VOICE /
FXS
FXO
E&M
FAX
XMT
RCV
XSG
RSG
RXT
FCR
RD
TM
V35
EXT
MDM
DSU
TA
COMPOSITE
LINK
28.8
DTR
DBUP
OH
DATA/
XMT
RCV
FC
COM
ORIG
VOICE /
FXS
FXO
E&M
FAX
XMT
RCV
XSG
RSG
STATUS
CD
RCV
XMT
CTS
56
RTS
NS
OOS
2B
COMMAND
FAX 1
101 MDM/TA
Composite Link
DataTalker
Voice/Fax
Channel 1 E&M
Trunk
PSTN
Trunk
Trunk
Station
Station
Telephone
PBX
Asynchronous
Channel
Data / Voice / Fax Concentrator
VOICE /
FAX 2
FXS
FXO
E&M
FAX
XMT
RCV
XSG
RSG
COMPOSITE
RXT
FCR
RD
TM
V35
EXT
MDM
DSU
TA
LINK
STATUS
28.8
DTR
DBUP
OH
DATA/
COMMAND
XMT
RCV
FC
COM
ORIG
VOICE /
FAX 1
FXS
FXO
E&M
FAX
XMT
RCV
XSG
RSG
101 MDM/TA
CD
RCV
XMT
CTS
56
RTS
NS
OOS
2B
DataTalker
Minicomputer
Voice/Fax
Channel 1 E&M
Trunk
Trunk
Trunk
Station
Station
Telephone
PBX
Local Site

Advertisement

Table of Contents
loading

Table of Contents